Cisco WAN :: Maximum Etherchannels In 2960 / 2960S?
Apr 6, 2011I am interesting what is a number of maximum supported etherchannels in 2960 and new 2960S switches?
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Maximum Etherchannels In 2960S Using Flexstack
Oct 25, 2011how many etherchannels can the 2960S support when it is stacked? I understand it initially has 6 channels.
View 2 Replies View RelatedCisco Switching/Routing :: Maximum Number Of EtherChannels On 2960S
Apr 19, 2013what is the maximum number of etherchannels i can build on a Cisco 2960S stack. We hoping to connected 15 servers using 2 port channels between two stacked 2960 for redunancey. So what is the max number of channels can i build using the 2960S? Is the max 6 or is it more?
View 4 Replies View RelatedCisco Switching/Routing :: 2960S / LAN Design Using 10G EtherChannels?
May 11, 2011We are designing a LAN Network for ourselves.The proposed design is as follows:
4 x 2960S switches in a Stack Access-Stack-I 4 x 2960S-PoE switches in a second Stack Access-Stack-II
2 x 3750X switches in a Stack Core-Stack
Now I would like to connect it in the following manner ?First,I would like to use EtherChannel using the 10Gig LinksSecondly, I would like to use Cross-Stack EtherChanel too.I have given a graphical illustration of the connectivity Now my Qs: a) Will the 2960S supports EtherChannel using the 10G links and the 3750X too... b) Does the proposed solution will work... or It will have any problems.
Cisco Switching/Routing :: Maximum Switches Per Stack For Catalyst 2960
Apr 23, 2007Any one who knows where I can find a documentation where it says the maximum switches per stack for the Catalyst 2960 family?
View 2 Replies View RelatedCisco Switching/Routing :: Maximum VLANs In Transparent Mode 2960
Nov 22, 2011On a low-end switch like a 2960 the maximum VLANs is 255, as shown in the output of VTP status:
Maximum VLANs supported locally : 255
Number of existing VLANs : 245
When the VTP mode is changed to transparent, VLANs from the extended range can be added without increasing the number of existing VLANs - e.g. if I create VLANs 3000 - 4000 the number of existing VLANs is still listed as 245.
If MST is used to cut down on the number of spanning-tree instances - and assuming propagation of VLAN configuration via VTP is not required - is there any downside to using transparent-mode VTP to increase the number of available VLANs? It does feel like I'm cheating the maximum listed in the datasheet.
Cisco Switching/Routing :: Memory Leak On Catalyst 2960 And 2960S - Similar To Bug CSCts52797
May 6, 2013after upgrading about 35 Catalyst 2960 and Catalyst 2960S to IOS 15.0(2)SE2, we experience a memory leak on several switches. After some days / weeks the switches are not accessible via Console/Telnet/SSH/Web any more. Only SNMP seems to work properly.Attached users do not experience any decrease in service.
Trying to connect to the console, we get following error message:
"% Low on memory; try again later"
The only (temporary) solution is to reboot the switch. The behavior is similar to Bug CSCts52797.With regards to the Bug notes this bug should only affect Catalyst 2960 with 64MB of RAM and should already be solved with IOS 15.0(2)SE2.
We experience the erroneous behavior with
-WS-C2960-48TC-S running IOS 15.0(2)SE2
-WS-C2960S-48LPS-L running IOS 15.0(2)SE2
Cisco Wireless :: Etherchannels Flapping / Stacked 3750 To WLC5508?
Feb 18, 2013We're running two 5508 WLCs running 7.0.235.3 pushing out 7 WLANs. They are both live. Each WLC is connected to the same stack of 3750G running 12.2(44)SE6 via Etherchannels.I'm getting tons of MAC flapping errors similar to this:9373213: Feb 19 10:53:54.564 CST: %SW_MATM-4-MACFLAP_NOTIF: Host 843a.4b3c.4cec in vlan 752 is flapping between port Po12 and port Po11Each portchannel consists of ports on each of the two switches in the 3750 stack. Only VLAN 752 shows the flapping activity. LAG is enabled on the each of the WLCs. The portchannel and interface configs are identical, minus the channel-group command of course.Maybe completely unrelated....looking at CDP neighbors from the switch is incorrect:
WLC1 Gig 2/0/44 157 H AIR-CT550 Gig 0/0/1
WLC1 Gig 1/0/21 157 H AIR-CT550 Gig 0/0/2
WLC1 Gig 1/0/20 157 H AIR-CT550 Gig 0/0/3
[code].....
Cisco Switching/Routing :: How Many EtherChannels Supported In Catalyst 3750-E
Oct 13, 2012I am working in an environment where i have to use more etherchannels, any way that how many etherchannels could we create on Cisco Switch 3750 e. do they can utilize high process resources of CPU.
View 4 Replies View RelatedCisco Firewall :: 5525-X Cannot Create New Sub-interfaces / Etherchannels Through ASDM 7.1(1)
Apr 9, 2013We are suffering an issue with ASDM 7.1(1) on a 5525-X with 9.1(1) software. In the Configuration --> Interfaces window, I can modify parameters on physical interfaces, I can modify parameter on subinterfaces, but I cannot create new subinterfaces or Etherchannels through ASDM.
When I create a subinterface, entering all parameters, interface name, vlan id, security level, etc., then I click on "Apply" button and nothing happens. It doesn't send anything to ASA. If I click on another window, ASDM ask for applying changes, I click on it, but nothing is applied and window doesn't change. It happens only when creating new interfaces. If I create them through CLI, then I can modify parameters without any problem.
I have tried re-installing java and I have tested with 6.31, 7.9, 7.11, 7.17 Java versions, from Windows XP, Windows 2003 Server and Windows 7 computers with same issue. Also with Linux Mint distro with IcedTea Java.
Cisco Switching/Routing :: Add 2960 To Stack Of 4 X 2960 Switches
Feb 7, 2012I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies View RelatedCisco Switching/Routing :: 2960-S To 2960-LST Configuration Over Fiber?
Feb 11, 2013I have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies View RelatedCisco WAN :: 2960S / QoS Configuration For Voice?
May 14, 2012This is my first attempt in configuring the QoS,
Issue:
IP-phone -->2960S ----> 6506E ----> 2811 --- > provider MPLS cloud ----->2811 --->C3548---->2960S-->ip phone
i have my configuration for 2960S and 6506E but am strugling with 2811
Cisco Switching/Routing :: 2960S And MLS QoS Map
Oct 8, 2012I have C2960S-48FPS-L and C2960S-24TS-S both of them are using C2960S-UNVERSALK9-M image with version 15.0(2)SE on both I run "mls qos"
and on 48FPS-L I run "mls qos map cos-dscp..."on 24TS-S I cannot run it. there is no such command. there is just "mls qos rewrite..." and "mls qos srr-queue..." variants.
I thought that one image give the same set of commands...?
Cisco WAN :: Stacking Switches 2960S
Apr 7, 2012Im trying to Connect a 2960-S Catalyst Switch to a 3560 Catalyst Switch. It worth pointing out im newish to switching although i know some commands and what they do This is my first time connecting 2 switches together.
They are connected via a crossover cable and have green lights flashing on the connected ports When i run "show CDP neighbours it sees the new switch Unable to ping new switch...just timesout Here is the the interface on the 3650
GigabitEthernet0/40 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 001b.532f.8428 (bia 001b.532f.8428)
Description: Uplink to Switch 2
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
[Code]....
Cisco WAN :: 881 Maximum Throughput
Jan 18, 2011I need to provide a router to connect Internet circuit and run IPsec to MPLS network. Circuit is 10Mbps.
What is the max a Cisco 881 can handle if running IPsec?Also, if you are aware of any branch router (1941) which allows connection to future 4G LTE .
Cisco WAN :: How To Get 871 Maximum WAN Speed
Jul 9, 2012I've just connected via pppoe to a fibre 70/40mbs service but only get around 12mbs bandwidth. The FE4 interface reports running at 100mbs Full Duplex so was wondering if the dialer interface has some kind of limit around 12mbs?
If the router is limited to 10/12mbs of WAN throughout, any similar router with greater WAN throughput more suitable for a fibre service.
Cisco :: 2960S Catalyst Access Switch From VPN
Dec 10, 2012I have a 2960S Catalyst switch in my LAN, with the firewall and the servers in the same VLAN (vlan 3).All the servers and the firewall are in the vlan 3 are in the "192.168.19.0/24" subnet, the firewall has the IP "192.168.19.1".I can land on the firewall with a VPN (192.168.130.0/24) which has a complete view on the subnet 19/24.I can access, manage and get SNMP information of the Catalyst from the servers but I can't do the same from the VPN.Is there some feature I need to enable on the switch in order to allow 192.168.130.0/24 to access it?
View 4 Replies View RelatedCisco Switching/Routing :: STP Between 2960S And SG300
Dec 8, 2011I am currently having an issue with connecting a Catalyst 2960-S switch to a Small Business SG300 switch. When I connect them they are unable to form a link. When I do a show spanning-tree it says the mst link is in dispute.
View 1 Replies View RelatedCisco Switching/Routing :: 2960S QoS For VoIP?
Mar 25, 2012I read some papers about QoS. The thing is that I have to implement 30 switches with QoS to connect to a lot of Cisco IP phones. The switches are Cisco 2960S with code image "C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE3". Should I use autoQoS feature or manually configure them?. How should I treat uplinks between access switchs and core/distribution? I have a lot of doubts regarding queueing, because all the info I had read its for another model/image.
View 4 Replies View RelatedCisco :: IP SLA Responder On Catalyst 2960S Stacked?
Oct 19, 2011I have a pair of switches stacked:
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
1 52 WS-C2960S-48FPS-L 15.0(1)SE C2960S-UNIVERSALK9-M
* 2 52 WS-C2960S-48FPS-L 15.0(1)SE C2960S-UNIVERSALK9-M
When I try to enable ip sla responder on the stack I get:
%SYS-3-HARIKARI: Process IP SLAs Responder top-level routine exited
I have been able to find a bug in the toolkit. Should ip sla responder be supported on the stack as above?
Cisco Switching/Routing :: Mix 10G And 1G Uplinks On 2960s?
May 16, 2013I'm looking at the WS-C2960S-48TD-L and have a question about the uplink ports. Is it possible to mix 10G on one uplink and 1G on the other? The datasheet says 2x10G SFP+, 2x1G SFP so I am thinking mixing is not possible.
View 6 Replies View RelatedCisco Switching/Routing :: How To Use USB Option On 2960s
Nov 5, 2011just got new hardware and decided to try the newer USB port for IOS upgrades. I could not get the switch to recognize my 2gig flash drive. Do I need a proprietary stick or special format?
I also noticed when I removed it the switches crash dump and rebooted?
Cisco WAN :: 2960S Post Failures If Break Into ROM?
May 8, 2011I have over 20 units doing the same thing and it seems to be a software isssue but i dont see any bugs or posts on it. This is only on 2960S switches and not 2960 or 2960G units.
If i use the password reset feature to break the units into rom and then type "boot" instead of power cycling the unit, they will fail MBIST post tests. If the unit is power cycled or left to boot normally on its own, there is no issues and all post tests pass. I know MBIST is Memory Built In Self Test and was thinking maybe breaking the unit into rom disrupts those memory tests for some reason. I tried the following software and got the same results with all of the images:
122-55.SE2
122-55.SE
122-53.SE2
122-53.SE1
Logs attached are from the same switch, one with password reset procedure used and while left to boot on its own.
Cisco :: 6509 - Maximum Distance For VSS And VSL
Feb 24, 2010how much distance can we have VSL,
I have 2 x 6509 serving as redundant switches and now i plan to upgrade to VSS, but both switch are 2KM away from each other.
Cisco WAN :: Maximum T1's That Can Be Bundled In A 2911
Mar 11, 2013What are the max number of T1's that can be bundled on a 2911 router?
View 0 Replies View RelatedCisco WAN :: ISR 819 Maximum Recommended Throughput?
Jun 12, 2012We are looking at providing an ISR 819 for one of our customers using FTTC & 3G for failover .. However, I cant seem to find any recommended throughput guidence for the device? We could be looking at up to 80Mbps via the ethernet interface and I just dont know if the device will cope?
View 4 Replies View RelatedCisco WAN :: 3750X - Maximum Interfaces With Pim?
Jun 5, 2013on 3750X how many interfaces can be configured with PIM activated on ?
View 2 Replies View RelatedCisco Security :: PIX 535 Maximum Connections
Jul 5, 2011We have a PIX 535 with unlimited lisence, it has 1,048,953 in use connections because the timeouts have been changed to 24 hour. I am addressing this issue but was wondering why its so high when the max concurrent sessions is supposed to be 500,000 as listed in the product spec. Also when it reaches it max and cannot allocate a connection what PIX syslog error message number would it send?
View 1 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.2 Maximum User ID
Jan 5, 2013what is the maximum user IDs that I can create to the ACS server? The client have an ACS appliance with version 5.2.
View 2 Replies View RelatedCisco WAN :: C4507R+E - Maximum Routes Sup 7E?
Mar 10, 2013I'm using a Catalyst 4500 switch (C4507R+E) with Sup 7E. Cisco Datasheet of this switch says that it can learn maximum 256K IPV4 routes. Currently it just learns 10330 ipv4 routes. However when I show platform hardware ip route summary, it seems that the FIB is just free 100K routes as below output:
Entity total used free util%
Entries 260096 10332 249764 3
UC Ipv4 110592 10331 100261 9
unused 147456 147456 0 100
My question is: Can I make use of all 147456 unused routes? Or these ones have to use for any special purpose?
Cisco :: Adding 2960S Switch To Network And Voip?
Apr 16, 2012I have 6 cisco switches already on my network and I just got a 2960S PoE switch that I need to enable for VoIP. The voice vendor is coming in to setup our phone system for VoIP and I need to enable this new 2960S 48 port switch for the VoIP phones, I don't know how to do that, or other taskes needed for this project.
I was told that I need to uplink the new 2960S with the Catalysy 4507R using an ethernet cable and to "trunk the ports" and enable the 2960S as a VTP client - ok great - how?
I was told I also need to use the switch port voice VLAN command for the new VLAN - again, great - but how?
I actually was able to telnet into the switch and I gave it an IP and I created a new vlan but thats all. We are using non Cisco IP phones.
Cisco LAN :: 2960S POE Switch - Monitor Network Bandwidth?
Aug 13, 2012I have a cisco catalyst 2960-s PoE switch. I have a web access to the switch and am able to get statistics on each port. However, I am wondering if there is a way to have a diagram of the trafic on each port?
Also, what is the best way to monitor the trafic on a router ( i have a cisci 1811W)