This is my first attempt in configuring the QoS,
Issue:
IP-phone -->2960S ----> 6506E ----> 2811 --- > provider MPLS cloud ----->2811 --->C3548---->2960S-->ip phone
i have my configuration for 2960S and 6506E but am strugling with 2811
Is there any additional configuration to be done on the 5508 WLC for Wireless Laptop / Voice Roaming? I tested with Wireless IP Phone and found some blankness in voice , whereas i have other access point nearby , which wasn't switching over easily .
View 3 Replies View RelatedRecently I'm working with my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET,This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.Access-list 100 permit ip any any dscp default,class-map match-all QoS_Floor_Limit, match access-group 100.
View 1 Replies View Relatedmy client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.
Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET
This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.
access-list 100 permit ip any any dscp default
class-map match-all QoS_Floor_Limit
match access-group 100
!
!
policy-map QoS_Floor_Limit
[Code]......
provide a sample Voice Vlan configuration for the Cisco 2960 POE switch to work with the Non-Cisco IP Phones?
Will these commands work? Vlan 2 is the new voice vlan, Vlan 1 is the data vlan.
mls qos
interface fastethernet 0/1mls qos trust cos switchport nonegotiateswitchport mode trunkswitchport trunk encapsulation dot1qswitchport voice vlan 2priority−queue outspanning-tree portfastspanning−tree bpduguard enable
vlan 2name voice
I am trying to setup intervlan configuration and stuck on a problem. Here are the details:
1. Switches Catalyst 3750-x (as core switch) and Catalyst 2960S (as access switch)
2. Both switches have VLAN 20 and VLAN 1 on their database and both are active. BTW, after I figure out how to properly configure interVLAN routing the native VLAN 1 will not be used anymore. This is just an initial test.
3. VLAN 20 SVI interface (IP 192.168.20.200) on 3750 is up and can be pinged from catalyst 2960.
4. VLAN 1 SVI interface (IP 192.168.170.200) on 3750 is up and also can be pinged from Catalyst 2960.
5. Catalyst 3670 can ping a client computer (IP 192.168.20.10) connected to Catalyst 2960.
6. IP route enabled on 3750
7. Trunking is enabled on etherchannel connecting both 3750 and 2960
8. Client computer in VLAN 20 (connected to 2960) can ping VLAN 20 SVI interface 192.168.20.200 on switch 3560.But, the client computer in VLAN 20 can not reach any computer in VLAN 1 and vice versa. Strangely, the switches which these computers are connected to can ping each other or any connected client copmuters without any problem as described above.
One of our clients is replacing some of their aging network components with 4 Cisco 2960S switches. Unfortunately in this case, my skills of switch configuration are greater than my skills of network design. I have a really crude network diagram of their basic network layout (4 servers, 4 switches, and a number of endpoints).
How would you experts design the physical connections in such a way as to facilitate some redundancy?
I just recently bought a ASA5505 with a licence that can have 2 WebVPN Peers, I would like to have a phone to my CCME server as one of the options within that web-vpn thingy.
View 3 Replies View Related i need any one exact IOS from below list .can some provide me the link.
15.1(0.20)T
15.0(1)M1.4
15.1(24.6.26)PIL13
15.1(0.2.12)PIB13
15.1(1)XB1
15.1(0.0.10)PIL14
15.1(1.7.1)PIA13
15.1(1.7.1)PIA14
15.1(0.0.3)PIL15
We recently purchased the Cisco Router 2951 router with the IOS 15.0. I have tried to put in my VIC2-4FXO card in it. When I did show invetery, it detected the card.[code] When I tried to configure the voice port by typing voice port, it shows % Invalid input detected at '^' marker. I have tried to reset the cad and replace with another one.
View 3 Replies View RelatedI have one 2821 router. Which ios will support both voice and vpn?
View 1 Replies View Relatedhow do I access voice mail
View 1 Replies View RelatedMY voice conversation on magic jack breaks up when I download a movie to my direct TV. I have a Belkin F9K1103V1, N750Db. I'm not using WiFi, Im wired to ports on back of Belkin.
View 3 Replies View RelatedCan I configure two voice vlans on the same physical port?
View 2 Replies View RelatedSince CIPC is isntalled in the PC, and PC definitely getting an IP address from the data IP network segment instead of the voice IP network segment, so how to gurantee the following? 1. How the CIPC registered to the CME/CUCM 2. How to gurantee the QoS for the CIPC's voice traffic since the source IP address of the CIPC is belong to the IP network segment?
View 4 Replies View RelatedWe're looking at implementing a new phone system which will use voice over ip. Currently we have a mixture of Cisco 3750 and Cisco 3550 switches which don't support power over ethernet. Its been suggested we could continue using the current switches and power the new phones using power adapters.
Int terms of implementing qos (we don't have any at the moment) for the voice will a Cisco 3550 be OK and will having a mixture of different models using 3550 and 3750 pose any challenges with the qos policy for the voice. I believe there are differences in that the Cisco 3550 doesn't support srr-queues but having little experience with qos I'm not sure what impact this will have if any?
I have few queries abou the Cisco 880G series router.
1) Suppose if we have a 3G service enabled SIM card then can we insert the same on the Cisco 880G router and browse internet from the LAN of 880G?
2) I think the HSPA+ standard supports 84 Mbps downlink speed..... so is it supported on 880 G router?
3) Can we configure Cisco 880G as a CME?
I have recently purchased a srp527w and I am thinking to buy a Cisco wireless ip phone 7921g. Does it works with the srp527? Do I need another device betweenn my srp527 and the ip phone? or it just works by configuring the voice vlan. If so, what phone would it work, the analog or the ip phone?
View 2 Replies View RelatedI have a cisco2811 router and i want to convert or make it to be a voice enabled router? it has a current image/ios of (C2800nm-adventerprisek9-m), version 12.4(5a).
View 4 Replies View RelatedI had already posted for voice modules for cisco 2811 but not able to find it. But here are a few questions regarding i
1. I am trying to configure a cisco 2811 with FXS ports . I am using an NM-HD-2V with a VIC3-2FXS. I am using the right modules. Also I believe we need PVDM mosules installed in the NM-HD-2V. We have PVDM-12 modules. Will that work or is 2811 compatible only with PVDM2-xx modules.
2. We are also trying to configure a cisco 2811 with PRI port. We plan to use an NM-HD-2V and a VWIC-1MFT-T1/E1. If they are correct and if we need only PVDM2-xx modules.
3. Also we are trying to configure a cisco 3845 with PRI and we plan to use the same as in 2811 that is NM-HD-2V, VWIC-1MFT-T1/E1. And here also we are not sure if we need only PVDM2-xx DSP modules.
We have the below. Does this support Voice commands ? Or do we need a change of the router itself ? Or any licensing ?
C3825-ADVENTERPRISEK9-M, Version 12.4(24)T8
We have installed a SRST in one of our remote offices. They have ISDN Primary, and we have a 6mb MPLS link to our main HQ with 400k of QoS on the line. During the day, both Internal calls over the MPLS and external calls over the ISDN break up, but it doesnt happen all the time, i.e in a day the morning will be ok, then the users experience the break ups in the afternoon, then its everything is ok again.
The only factor that the calls share is the Lan infrastructure i.e the 3750G switches (7) of them which are stacked.We did have MAC flapping errors, and our telecoms provider suggested that it maybe these causing the issues, however we have got rid of all MAC flap errors, and are still receiving voice break ups.
Because the Lan switches are the only "item" both calls share, I am wondering now if the setup of the switches is correct. [code]
I just got Windoes 7 and it has a Fax icon to go to. It want to knoe if I am connected to a moden or network service.I don't really wnt to buy a $200.00 modem to replace the HP 920 Fx machine that is going to some good person. I have wireless gateway 2wire modem thingey sitting on my dest to support ATT UVerse
View 1 Replies View RelatedI would like to develop Voice Activation Detection using this sample program (google: ****/p_238-voice-activation-detection-voip) in Visual Studio 2008. But according to this website Visual Studio 2010 is highly recommended. Why VS 2010 is better than VS 2008?
View 1 Replies View RelatedWhat's the best router / handset to get to practice for CCNA Voice?
View 2 Replies View RelatedI intend to deploy a voice+data network using some old 3745 and 2811. The network in effect has six 3745 in a hybrid topology at different locations and each having three WIC-2T, one WIC-4T, three NMHDV-2E1. That's pretty much juicing out the maximum from these routers These will serve as my core routers and for access I will be using my 2811s with more VWICs and lesser WIC-2T to give voice and data to subscribers. The 2811s will have links to multiple 3745s. The NMHDV-2E1 will serve for the voice needs at the 3745 locations. All the WAN links will be E1. All my telephones will be on analog voice using traditional EPABX with CEPT/ PRI E1 cards for connecting to the routers. And for data, ethernet ports.Two of the routers will have E1 links to the PSTN and Internet which has to be extended to all my folks. Now, for the tricky part, all my network modules are refurbished stuff from ebay and all the ports will have links on them. I intend to use OSPF with only the backbone area.
View 7 Replies View RelatedThough i am working on cisco call manager.I know some stuffs about Call Manager. Diff between CallManager, GateKeeper and Voice Gateway.
View 7 Replies View RelatedSince I am new to VOIP and am getting confused with the responses online on how to connect to a commercial phone system I thought I would ask here. I have a small voice router (1751) running CME with 2 Cisco 7940 phones. I would like to hook it up to a commercial line, but not sure how to. What specific card will I need for my voice router to connect it to the outside world (FXO right)? I see where they talk about hooking it up directly to the LAN line, another using a commercial phone system, and then the others using a PBX,ect... So confused to say the least. I assume I need an FXO port to connect to the POTS, but not sure if there is anything else I’m missing in the setup...
View 4 Replies View RelatedWhen I try to configure a voice port (like voice-port 0/0/0:15) after doing a conf t, it gives me an error of invalid input detected.We are using a Cisco 3945. We have successfully setup 3825 and 2851 in the past.
View 2 Replies View RelatedI'm planning to separate voice and data traffic with two vlans. I have a COR switch catalyst 3750, a UC560 for VOIP with SIP trunk and SGE2000P as access switches. The thing is i had configured VLAN1 (data vlan) and VLAN8 (voice vlan), i've created the vlan 8 in the database on 3750 and let pass those vlans through a TRUNK port. In the SGE2000P configuration i've created the VLAN8 and the the ports as trunk for letting pass the two vlans for the PC and the IP phone. This works but some phones aren't registering, and for example i've unplugged a register phone and plug and doesn't registering anymore.
View 0 Replies View RelatedWe are about to install a new VoIP system (Allworx, which I did not select) and need to set up a new VLAN with QOS quickly for my SG 300 and SG 200 switches. I have the default VLAN1 at 10.0.0.0/24 and will be setting up VLAN10 at 10.1.0.0/24 for voice. There are a few other VLANS on the switches as well. I really don’t get the particulars of using a Voice VLAN vs. Smartport, but is one better than the other for this and what would be some good default settings to start with. I have command line and VLAN experience; I just haven’t set up a VLAN for voice from scratch.
View 1 Replies View RelatedI am currently working on our Cisco voice platform at work.
Our Cisco firewall engineer has left and I have been given the task of looking after the firewalls as our Chief Exec seems to think that Cisco Voice is similar to Cisco ASA firewalls,
Are there any books/videos out that you can recommend to learn the about firewalls quickly.
I have a question regarding firewall configurations. Is it possible to have two interfaces ( for two internet service providers) one for voice and one for data. Can I have two Outside Interfaces that one will apply to a pppoe client group and the other will apply to a static IP? Is this possible and if so What would be the steps on applying this connection? Also to note I have a point to point connection already established for the pppoe. I also have another point to point connection for data, but however I do not know how to apply this to the firewall.
View 3 Replies View Related