Cisco :: IP SLA Responder On Catalyst 2960S Stacked?
Oct 19, 2011
I have a pair of switches stacked:
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
1 52 WS-C2960S-48FPS-L 15.0(1)SE C2960S-UNIVERSALK9-M
* 2 52 WS-C2960S-48FPS-L 15.0(1)SE C2960S-UNIVERSALK9-M
When I try to enable ip sla responder on the stack I get:
%SYS-3-HARIKARI: Process IP SLAs Responder top-level routine exited
I have been able to find a bug in the toolkit. Should ip sla responder be supported on the stack as above?
View 6 Replies
ADVERTISEMENT
May 12, 2013
I'm designing a hierarchical 3 layer campus network with different switch blocks .We need 10Giga Ethernet in the core to distributions and access layer , I was thinking about using a pair of catalyst 4509E in each block.after that I got interested in 4500Xs , in comparison with 4509Es they are much thinner and saves more room in rack space .I wanna use 4500X in my distribution layer .
The question is , as you know 4500Xs have 40 10Giga Ethernet ports , in some of my switch blocks I have more than 40 access switches (40 uplikns to distribution ) i wanna know how many of 4500Xs can i stack together ?
View 5 Replies
View Related
Dec 10, 2012
I have a 2960S Catalyst switch in my LAN, with the firewall and the servers in the same VLAN (vlan 3).All the servers and the firewall are in the vlan 3 are in the "192.168.19.0/24" subnet, the firewall has the IP "192.168.19.1".I can land on the firewall with a VPN (192.168.130.0/24) which has a complete view on the subnet 19/24.I can access, manage and get SNMP information of the Catalyst from the servers but I can't do the same from the VPN.Is there some feature I need to enable on the switch in order to allow 192.168.130.0/24 to access it?
View 4 Replies
View Related
Jul 25, 2011
I have a CiscoWorks LMS 2.6 and i would like to know if the new Switches Catalyst 2960-S Series are supported with this LMS version?
View 1 Replies
View Related
Aug 8, 2012
Just I have upgraded some 2960S to IOS 15.0(2)SE from a IOS 15.0(1)SE3 and the catalyst don't switch any IPv6 traffic. Don't work any RA and also don't work any unicast IPv6 traffic from any interface. I can see some references to IPv6 changes in the FHS (First Hop Security) in the Release Notes, but no any reference to changes in the configuration.
The switches don't have any IPv6 specific configuration and the sdm is the default templata. Returning to 15.0(1)SE3 everything work ok.
On Catalyst 2960, and 3560E this IOS version seem to work fine with IPv6.
View 1 Replies
View Related
Mar 22, 2012
configuring 802.1x authentication on ACS 5.1.0.44 & Catalyst 2960S switches.All the documents i have found seem to have incorrect screen shots or missing steps.I have found a doc external to Cisco [URL]however this just hangs when attempting to complete the task in figure G.The other docs are for configuring IBNS & assume that 802.1x is already configured.
View 1 Replies
View Related
Jun 20, 2012
i want upgrade my catalyst 2960S and 3560x at midnight, but i am worried about config loss. If i upgrade my switch throught web interface, will need I reconfigure the switch?
View 2 Replies
View Related
Dec 1, 2010
I have a new problem with Catalyst 2960S. We have four switch in a stack and now I get the message:
“%PLATFORM_RPC-3-MSG_THROTTLED: RPC Msg Dropped by throttle mechanism: type 37, class 14, max_msg 32, total throttled 73968 (hostname1-2)”
Traceback= 13A686C 160862C 160E0B4 15E2088 184FD48 18467B8
sh switch de
Switch/Stack Mac Address : 68bd.abc9.0000
H/W Current
[Code]....
View 36 Replies
View Related
Nov 26, 2011
we have Catalysts 2960S for switching in our Wireless high capacity backbone network. As agregation switch we are using 3560x.
I just need to know, if are these 2960S good solution for igmp snooping for whole IPTV stream. It put only a range from backbone and put out on another port. But just specified multicast addresses.
Imput will be 239.128.0.10 to 239.128.0.20 on Gi 0/1,Output wil be 239.128.0.10 - 15 on Gi 0/24
IPTV will be separated on different VLAN for eg VLAN 20,Is needed any priorization configured od switches?,The capacity for IPTV is around 500 mbps
View 4 Replies
View Related
Jan 3, 2013
I recently tried to manually format the flash on a model WS-2960S-48TS-L switch running IOS version 15.0(2)SE. While executing the operation I got the following error - mifs[8]: Failed to create superblock %Error formatting flash (I/O error).As a result the flash is no longer accessible by the switch. I spoke with Cisco and they indicated that a switch reload would remount the flash and make it accessable again but the .bin file would need to be reloaded using the xModem recovery procedure (what a pain).The next IOS version 15.0(2)SE1 will supposedly fix this bug but it has not been released yet. In the meantime if you are running 15.0(2)SE you may want to hold off performing a "format flash:" function on a 2960S.
View 3 Replies
View Related
Nov 5, 2011
We are using catalyst 2960S Lan Base IOS on Radio towers. We just bought 50 Accest points, thas are GPS synchronized. Problem is the APs need to be connected on L2-mac betwen each other. But at this time we are using port isolation on each switch (tower) by protected port function to isolate clients from each other.
My question is, is possible to specifi a Mac addresses in specific vlan thats can comunicate betwen protected ports? On tower is one Master unit and others are slave. I thing there is only 1 dirrection comunication - from master to slave.
View 2 Replies
View Related
Oct 30, 2012
specifying Cisco devices and I've made an error.I have 2 Catalyst 2960S switches (C2960S-24PS-L).Based on this snippet of web copy from the Cisco website:What's new for the Cisco Catalyst 2960-S Series Switches with LAN Base Software: # 10 and 1 Gigabit Ethernet uplink flexibility with Small Form-Factor Pluggable Plus (SFP+), providing business continuity and fast transition to 10 Gigabit Ethernet I bought a cable assembly "SFP-H10GB-CU3M" (3 meter copper twinax cable with 10GB SFPs on each end). Unfortunately, it appears after more careful reasearch that my specific model 2960S's are not directly compatible. , can I force these 10GB SFPs down to 1GB and get them to work with my switches or do I need to return and repurchase?
View 1 Replies
View Related
Sep 27, 2012
I just bought a Catalyst 2960S to test out the feature "Port-Based Address Allocation" which is required for our factory. I followed the instruction from Cisco IOS and did all the steps but I could not get it to work, my network client did not received the expected IP address that I configured.
View 8 Replies
View Related
Jan 28, 2012
Multicast is not working between our two datacenter, we have catalyst 2960S (two stacked) as the internal lan switch, and catalyst 3560E as the external switch, same configuration for both datacenters.The two sites are connected using metro, the external switch (3560) is doing qinq and encapsulate the data from the internal switch with the metro vlan (611).
IGMP snooping is disabled for all switches, although we prefer to enable it for the internal switches.For each datacenter there is a different firewall which also act as the router, we are using fortigate as the firewall.Following is the important configuration section:
Port 43 in the internal switch is connected to the external switch (both sites):
interface GigabitEthernet1/0/43
switchport mode trunk
load-interval 30
Port 3 in the external switch connected to the internal switch (both sites):
interface GigabitEthernet0/3
switchport access vlan 611
switchport mode dot1q-tunnel
no cdp enable
no cdp tlv server-location
no cdp tlv app
Port 8 on the external switch connected to the metro link (both sites) vlan 350 is the internet and 611 is the metro:
interface GigabitEthernet0/8
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 350,611
switchport mode trunk
vlan 611 on external switch:
interface Vlan611
ip address 192.168.168.2 255.255.255.0
no ip route-cache
no ip mroute-cache
View 6 Replies
View Related
Apr 15, 2011
I have several 2960s and 3750s and two 6506 (ws-cac-3000w) recently move to new location The power outlet is the same ,but Volt is different current 2960/3750 use this(one phase 3 wire) 220v and new location change to (from 3 phase 4 wire -> one phase 220v)6506 current using(one phase 3 wire) and will be change to (from 3 phase 4 wire -> one phase 220v)
I had search doc about power supply /cable , only show support single phase 220 v ,but not description vlot between each wire !!Does new location power outlet suit for 2960/3750s power and 6500 ws-cac-3000w ?!? Do I need chane power outlet back to current using?
View 1 Replies
View Related
Aug 30, 2012
I am administering a Catalyst 2960S switch and I would like to connect several computers to it. Some of those each have a static IP address. For a few of them, I would like the switch to dynamically assign an IP address to them via DHCP. Is the switch capable of doing this? If so, how can I do it? I tried looking through Cisco Network Assistant and I couldn't find it. Some web pages have suggested I telnet into the switch and issue commands like "ip dhcp ?" to see what commands are possible. I can telnet in and if I type but I get an "Unrecognized command" for both "ip ?" and "ip dhcp ?". This makes me think I'm reading the wrong web pages. I did come across the term "DHCP snooping". It seems relevant, but very difficult for me to grasp.
View 9 Replies
View Related
May 6, 2013
after upgrading about 35 Catalyst 2960 and Catalyst 2960S to IOS 15.0(2)SE2, we experience a memory leak on several switches. After some days / weeks the switches are not accessible via Console/Telnet/SSH/Web any more. Only SNMP seems to work properly.Attached users do not experience any decrease in service.
Trying to connect to the console, we get following error message:
"% Low on memory; try again later"
The only (temporary) solution is to reboot the switch. The behavior is similar to Bug CSCts52797.With regards to the Bug notes this bug should only affect Catalyst 2960 with 64MB of RAM and should already be solved with IOS 15.0(2)SE2.
We experience the erroneous behavior with
-WS-C2960-48TC-S running IOS 15.0(2)SE2
-WS-C2960S-48LPS-L running IOS 15.0(2)SE2
View 7 Replies
View Related
Mar 20, 2011
i have an Cisco ASR 1002 Router. I would like to connect our dezentral location to the Router.Unfortunately has this location an standard DSL connection with an dynamic offical IP Address.I have found an Config witch can handle an dynamic IP Addess (enclosed).
Is it possible to works witch the "set responder-only" command togehter with an dynamic crypto map? How I can configure it.
crypto isakmp policy 1 encr 3des hash md5 authentication pre-share group 2 lifetime 300crypto isakmp key xxx address 0.0.0.0 0.0.0.0 no-xauthcrypto isakmp identity hostnamecrypto isakmp keepalive 10 periodic
!
crypto ipsec transform-set dezentral-location esp-3des esp-md5-hmac
!
crypto dynamic-map fil 1 set transform-set dezentral-location set pfs group2 match address 150 reverse-route
!
crypto map Filialen 1 ipsec-isakmp dynamic fil
View 1 Replies
View Related
Sep 8, 2012
I have a network topology which you can see on image. All routers are Cisco 3745 with IOS (C3745-ADVENTERPRISEK9-M), Version 12.4(12). SW1 is L3- switch Cisco Catalyst WS-C3560E-24TD with IOS (C3560E-UNIVERSALK9-M 12.2(58)SE2). [code] After that I have problem. When PC with OS Windows 7 begins to work in corporate network, it sees "coflict ip addresses" and doesn't work with network. I've used wireshark and seen, when the PC send arp request a SW1 always send arp reply (see attached file). I think problem with command "ip sla responder", but I haven't searched information about it and I want understand this is bug or normal functioning.
View 1 Replies
View Related
Apr 15, 2012
Im trying to stack 2 3750E-24PD-S and 2 3750X-12S-S. The 2 3750E finds eachother and stacks with one master as they should. The problem is that and the 3750X does the exact same thing instead of joining the 3750E stack.Both runs the same IOS (c3750e-ipbasek9-mz.122-58.SE2).The stackingcables are connected like following atm (I tried booting up the switches one at a time and all at once, no difference in the result).
View 8 Replies
View Related
Apr 13, 2013
We are planning to implement the redundant physical connection from 5508 WLC to not stacked 3750 switches. The sheme is attached.
View 7 Replies
View Related
Jul 1, 2011
We've have a 2 SGE2010-48 port, stacked. 4 LAGS are denifed, two on primary, whitch are working, two on slave unit are NOT working. Devices connected to LAGS are de the same and same configuration (Cisco ASA 5510).
View 3 Replies
View Related
Nov 15, 2011
I have a 4 member stack of 3750's. We would like to take advantage of wccp and we understand that we will need to upgrade our switch licensing from IPBase to IPServices. My question is do we need to pay for a license for each member in the stack or does one IPServices license upgrade cover the whole stack?
WS-C3750G-48PS
WS-C3750G-48TSWS-C3750G-48TSWS-C3750G-48TS
View 1 Replies
View Related
May 10, 2012
I am about to buy 2x Series 500 switches but before that I have a design to be sure :I want to create a redondant network so it is the reason why I want to stack 2x Series 500 switches.Each server on my network (ESX and Windows 2008) are connected with two NIC (one port on the first switch , one port on the second switch), with trunk mode + etherchannel for LACP.
First question : I saw that the limitation is up to 8 etherchanel groups, can I have a mix of multiple servers on the same etherchannel group or should I create one etherchanel group for one server with only the two NIC inside?
Second question:I want to use the series 500 to do intervlan routing and want to be sure that if the the ports are in trunk mode with some vlan set on the card itself that the default gateway for the vlan will be propagated on the two switches (in stack mode) and will not cause any issues when both switchs works fine and if one switch crashes?
View 3 Replies
View Related
Jun 6, 2012
I'm trying to see if I can use both ethernet ports on a 2811 to run hsrp for non-stacked dual switch fail over. Then link the the NM-32A ports to L0, so the remote access server trying to use them can use the l0 ip and failover much faster (it's programming is limited). This is on IOS 12.4(25)f, though we are moving to 15 soon.
View 2 Replies
View Related
Jan 2, 2012
If we have 3 stacked 3750s# running Layer 3. Do we need license for every switch? or is it one license for the 3 switches? Also is the license associated with the MAC address of a specific switch? What i# am trying to know also, is if we have to install one license and it is associated# with one MAC and this switch failed.. will the Layer 3 be broken?
View 1 Replies
View Related
Feb 27, 2013
I currently have a stack of 3750G switches with a cross stack etherchannel connected to a 3750E stack in the distribution layer.The 3750G stack is running 15.0-2SE IP Base. I began noticing the Mac flap issue when I was Re-enabling dot1x on the switchports. As first I thought dot1x maybe have contributed to this so I removed it from the stack temporarily.I am still seeing Mac flap logs usually when a machine reboots or re-connects back to the network. These are all wired desktops.I started looking at the etherchannel configuration which is using LACP. The 3750E stack looks fine with all ports in mode active. On the problematic 3750G stack I noticed 3 of the ports in the etherchannel set to mode active and 1 port set to mode passive. The port shows as bundled but I can't imagine this is ok.The only other difference on this one port is there is no mls qos commands like on the other 3 interfaces in the port channel.I mainly need to know what the Mac flapping is about. Whether it is a bug or related to the current etherchannel configuration.
View 9 Replies
View Related
Mar 17, 2013
I have a customer who just bought a pair of N5K and wanted to replace his current HP E3800 as Core. He wants to use the 4 x stacked HP E3800 connect back to the N5K. Will I be able to utilize VPC through a bundled 2 or 4 x 10G (40G) connection (10 or 20G on 1 switch, and 10 or 20G on another switch) from the stacked HP E3800s to the N5548s? I know you can do that with Cisco 3750s.
View 1 Replies
View Related
Feb 18, 2013
We're running two 5508 WLCs running 7.0.235.3 pushing out 7 WLANs. They are both live. Each WLC is connected to the same stack of 3750G running 12.2(44)SE6 via Etherchannels.I'm getting tons of MAC flapping errors similar to this:9373213: Feb 19 10:53:54.564 CST: %SW_MATM-4-MACFLAP_NOTIF: Host 843a.4b3c.4cec in vlan 752 is flapping between port Po12 and port Po11Each portchannel consists of ports on each of the two switches in the 3750 stack. Only VLAN 752 shows the flapping activity. LAG is enabled on the each of the WLCs. The portchannel and interface configs are identical, minus the channel-group command of course.Maybe completely unrelated....looking at CDP neighbors from the switch is incorrect:
WLC1 Gig 2/0/44 157 H AIR-CT550 Gig 0/0/1
WLC1 Gig 1/0/21 157 H AIR-CT550 Gig 0/0/2
WLC1 Gig 1/0/20 157 H AIR-CT550 Gig 0/0/3
[code].....
View 2 Replies
View Related
Jul 16, 2012
We have two 3750-x stacked switches with IP base license. We need to upgrade them to IP services license. I read some where that it is possible to install IP serivces license to only management switch and no need to purchase/install same license to other switches on the stack. But, I could not find/recall where I read it and as far as I know it was not official cisco documentation.
View 1 Replies
View Related
Jun 3, 2013
I was wondering what general steps might be taken in order to "replace two(2) 3750 (stacked) with one (1) 3750X - Server Access". General steps and what I might have to do configuration wise. I know i'm copy pasting the existing configs into the new switch, but are there any caveats?
View 5 Replies
View Related
May 28, 2012
How many Switches can be stacked with WS-C2960S-48FPD-L at a max..
As per my Knowledge it is 4 and as below..
Switch 1 to Switch 2
Switch 2 to Switch 3
Switch 3 to Switch 4
Switch 4 to Switch 1
If yes then, is it mandatory to do the "Switch 4 to Switch 1" stack. why am I asking this is because this stack requires a long cable and the cable which comes with the Switch is only 0.5M.
View 3 Replies
View Related
Apr 2, 2012
My company is beginning to have a lot of sites were we are stacking 3 to 4 C2960S-48 switche.This is making "show running-config" very very long because of the 4 x 48 interfaces.I can’t find a CLI command that show me the running-config of a ranges of interfaces. If I for example would like to see running-config for switch 3 (interfaces 3/0/1-52)The Show Running-config will show all the interfaces (for the two first swtiche = 104 interfaces), which take a time before I reach to switch 3.I miss a CLI command like: show Running-config switch 3, or module 3, or show running-config interface range x/x/x-x ?I’m well aware of the CLI command show running-config interface x/x/x, but this will only show me one interface.
View 3 Replies
View Related
