Cisco Switching/Routing :: 3750 E And X Could Not Be Stacked
Apr 15, 2012
Im trying to stack 2 3750E-24PD-S and 2 3750X-12S-S. The 2 3750E finds eachother and stacks with one master as they should. The problem is that and the 3750X does the exact same thing instead of joining the 3750E stack.Both runs the same IOS (c3750e-ipbasek9-mz.122-58.SE2).The stackingcables are connected like following atm (I tried booting up the switches one at a time and all at once, no difference in the result).
View 8 Replies
ADVERTISEMENT
Jul 16, 2012
We have two 3750-x stacked switches with IP base license. We need to upgrade them to IP services license. I read some where that it is possible to install IP serivces license to only management switch and no need to purchase/install same license to other switches on the stack. But, I could not find/recall where I read it and as far as I know it was not official cisco documentation.
View 1 Replies
View Related
Jun 3, 2013
I was wondering what general steps might be taken in order to "replace two(2) 3750 (stacked) with one (1) 3750X - Server Access". General steps and what I might have to do configuration wise. I know i'm copy pasting the existing configs into the new switch, but are there any caveats?
View 5 Replies
View Related
Jan 2, 2012
If we have 3 stacked 3750s# running Layer 3. Do we need license for every switch? or is it one license for the 3 switches? Also is the license associated with the MAC address of a specific switch? What i# am trying to know also, is if we have to install one license and it is associated# with one MAC and this switch failed.. will the Layer 3 be broken?
View 1 Replies
View Related
Feb 27, 2013
I currently have a stack of 3750G switches with a cross stack etherchannel connected to a 3750E stack in the distribution layer.The 3750G stack is running 15.0-2SE IP Base. I began noticing the Mac flap issue when I was Re-enabling dot1x on the switchports. As first I thought dot1x maybe have contributed to this so I removed it from the stack temporarily.I am still seeing Mac flap logs usually when a machine reboots or re-connects back to the network. These are all wired desktops.I started looking at the etherchannel configuration which is using LACP. The 3750E stack looks fine with all ports in mode active. On the problematic 3750G stack I noticed 3 of the ports in the etherchannel set to mode active and 1 port set to mode passive. The port shows as bundled but I can't imagine this is ok.The only other difference on this one port is there is no mls qos commands like on the other 3 interfaces in the port channel.I mainly need to know what the Mac flapping is about. Whether it is a bug or related to the current etherchannel configuration.
View 9 Replies
View Related
Mar 17, 2013
I have a customer who just bought a pair of N5K and wanted to replace his current HP E3800 as Core. He wants to use the 4 x stacked HP E3800 connect back to the N5K. Will I be able to utilize VPC through a bundled 2 or 4 x 10G (40G) connection (10 or 20G on 1 switch, and 10 or 20G on another switch) from the stacked HP E3800s to the N5548s? I know you can do that with Cisco 3750s.
View 1 Replies
View Related
May 28, 2012
How many Switches can be stacked with WS-C2960S-48FPD-L at a max..
As per my Knowledge it is 4 and as below..
Switch 1 to Switch 2
Switch 2 to Switch 3
Switch 3 to Switch 4
Switch 4 to Switch 1
If yes then, is it mandatory to do the "Switch 4 to Switch 1" stack. why am I asking this is because this stack requires a long cable and the cable which comes with the Switch is only 0.5M.
View 3 Replies
View Related
Nov 15, 2011
I have a 4 member stack of 3750's. We would like to take advantage of wccp and we understand that we will need to upgrade our switch licensing from IPBase to IPServices. My question is do we need to pay for a license for each member in the stack or does one IPServices license upgrade cover the whole stack?
WS-C3750G-48PS
WS-C3750G-48TSWS-C3750G-48TSWS-C3750G-48TS
View 1 Replies
View Related
Apr 2, 2012
My company is beginning to have a lot of sites were we are stacking 3 to 4 C2960S-48 switche.This is making "show running-config" very very long because of the 4 x 48 interfaces.I can’t find a CLI command that show me the running-config of a ranges of interfaces. If I for example would like to see running-config for switch 3 (interfaces 3/0/1-52)The Show Running-config will show all the interfaces (for the two first swtiche = 104 interfaces), which take a time before I reach to switch 3.I miss a CLI command like: show Running-config switch 3, or module 3, or show running-config interface range x/x/x-x ?I’m well aware of the CLI command show running-config interface x/x/x, but this will only show me one interface.
View 3 Replies
View Related
Feb 25, 2013
I have two 3750x stacked switches , both with the latest firmware on them. I enter the configuration onto one switch and it obviously copies over onto the other switch. Although in the configuration I have both a console username and password and an enable password, when I try to log onto the initial switch that I entered the configuration on, I am prompted for a username and password, which works fine, but when I try to enter enable mode i get an error stating that no password has been set. However when logging onto the other switch I am not prompted for a username or password but when I try to enter enable mode I am prompted for a password and can access it with no problems.
View 1 Replies
View Related
Feb 18, 2013
We're running two 5508 WLCs running 7.0.235.3 pushing out 7 WLANs. They are both live. Each WLC is connected to the same stack of 3750G running 12.2(44)SE6 via Etherchannels.I'm getting tons of MAC flapping errors similar to this:9373213: Feb 19 10:53:54.564 CST: %SW_MATM-4-MACFLAP_NOTIF: Host 843a.4b3c.4cec in vlan 752 is flapping between port Po12 and port Po11Each portchannel consists of ports on each of the two switches in the 3750 stack. Only VLAN 752 shows the flapping activity. LAG is enabled on the each of the WLCs. The portchannel and interface configs are identical, minus the channel-group command of course.Maybe completely unrelated....looking at CDP neighbors from the switch is incorrect:
WLC1 Gig 2/0/44 157 H AIR-CT550 Gig 0/0/1
WLC1 Gig 1/0/21 157 H AIR-CT550 Gig 0/0/2
WLC1 Gig 1/0/20 157 H AIR-CT550 Gig 0/0/3
[code].....
View 2 Replies
View Related
Jun 30, 2012
Do I need the Universal image to perform stftp on a 3750 or 3750-X?
View 8 Replies
View Related
Oct 10, 2011
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies
View Related
May 21, 2012
We have a stack of switches that is at the max number of members allowed in the stack. Problem is we are running out of port density and need to add more ports. So instead of adding a whole new stack I would rather replace 2 of the 24-port swicthes with 48-port switches.
If the two 24-port swicthes we are removing are stack members and neither of them are the stack master, I should be able to replace the 24-port switches with the 48-port switches without bringing the master offline? If the new 48-port switches are running the same IOS version as the current 24-port swicthes, they should add themselves to the stack?Would I have to tell the new 48-port swicthes what switch numbers they are replacing in order for them to be added to the stack since we are at the max number of members?Also since the 48-port swicthes are replacing 24-port switches will the master give the 48-port switches the configuration for only the 24-ports?
View 11 Replies
View Related
Dec 9, 2011
some of our switches have the switchport mode trunk command configured between the 3750 switches but other 3750 switches connected to our 6509 core switch do not have the switchport mode trunk command to permit Vlans from going across the swtiches instead it has an ip address and says no switchport what is the difference between does two. Is trunking used only for Layer 2 and L3 is used to route interface vlans?
View 2 Replies
View Related
Oct 24, 2012
I have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies
View Related
Oct 8, 2012
Is a 3750 sw capable of handling full routing tables and what can you recommend in a small mutihomed BGP router or switch capable of handling full routing tables?
View 2 Replies
View Related
Oct 28, 2012
I have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies
View Related
Dec 17, 2011
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
View 4 Replies
View Related
Jul 27, 2012
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
View 4 Replies
View Related
Mar 24, 2013
In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies
View Related
Jan 24, 2013
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies
View Related
Nov 21, 2012
I am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies
View Related
Oct 17, 2011
I have a simple design with 3750. I configured a route-map which define a next hop. I defined this route-map on a policy on a vlan interface.When I test some ping and a debug ip policy and it seems that my policy never match.Is there any mechanism that prevent the switch from using PBR? I think of CEF .
View 5 Replies
View Related
Jan 28, 2013
In our datacenter we have a 3750 stack with IP base image. I have enabled PBR and reloaded the switch. Show sdm prefer says i am using default template. The reason i want to use PBR is that we have 2 firewalls on the same work and want to be able to have granular control over which gateway out of the network they use but still be able to access all internal resouces accross wan and locally.
Created access list to identify traffic:
access-list 10 permit 10.2.3.59 (test workstation on vlan 3)
Created policy:
route-map TestASA permit 10
match ip address 10
set ip next-hop 10.2.0.3
Assigned policy to the user vlan3:
ip policy route-map TestASA
Results:It changed the default gateway to the above gateway but i could not access any resources on any other vlan, could not access resouces accross wan.
View 16 Replies
View Related
Apr 16, 2012
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies
View Related
Sep 5, 2012
I have a simple design with 3750.I configured a route-map which define a next hop.I defined this route-map on a policy on a vlan interface.When I test some ping and a debug ip policy and it seems that my policy never match.Is there any mechanism that prevent the switch from using PBR?
View 10 Replies
View Related
Mar 11, 2012
I'm running into what seems a basic ip routing config problem with a Catalyst 3750 (IP Base) switch. I have several VLANS configured on the switch with IP routing enabled, and the switch is connected to the inside interace of a new ASA 5520 as follows:
ASA5520 IP (Default gateway): 192.168.1.1Switchport Gi1/0/1 is configured as a routed port, IP address 192.168.1.3 255.255.255.0Example VLAN is VLAN 100, IP address 192.168.100.1 255.255.252.0 From the switch CLI, I can ping all VLAN addresses, as well as the ASA5520, and the client laptop I'm testing with from VLAN 100.
From the client laptop on VLAN 100, I can ping all switch interface and VLAN addresses (inter-VLAN routing is working), including 192.168.1.3, but I CANNOT ping the default gateway at 192.168.1.1.
Here is the relevant configuration information on the 3750:
!
no aaa new-model
switch 1 provision ws-c3750x-24
system mtu routing 1500
[Code]....
View 4 Replies
View Related
Jan 1, 2012
I have a Cisco 3750 with private VLANS configured.. VLAN 2 is the "primary", VLAN 3 is "isolated" and VLAN 4 is "community". This is all working correctly, however I now have the need to another VLAN called "production". I need the production VLAN to be able to reach all the private VLAN hosts (community and Isolated), and vice versa
View 2 Replies
View Related
Oct 30, 2011
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?hes, do we need to enable the "ip routing" command manually for intervlan routing?
View 2 Replies
View Related
Dec 2, 2012
I have 2 ISP connected to Router A and Router B.Both the routers are connected to the core 3750 switch.. I want to send the traffic from the switch that goes to router A to router B..[code]
View 10 Replies
View Related
Feb 27, 2013
I have just bought two Cisco 3750 and stacked them. When in global config mode, The IP Routing Command does not exisit.
See Version below
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 05-May-11 15:40 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02800000
View 5 Replies
View Related
Nov 23, 2011
I am using a cisco 3750 in my network as a gateway, and above it I use a squid machine for caching my internet. My network is like this:
Basically I have two VLANs on my network which are VLAN10 and VLAN100, VLAN10 is the cooperate network of my office. VLAN100 is the management VLAN which i use for the switches. I keep the squid as well the client in VLAN10.
squid (192.168.1.50)---->cisco 3750(192.168.1.123)---->Distribution Switch(cisco 2960)---->client PC (192.168.1.5)
I have done nating on squid and internet is working pretty fine when I use the client gateway as the squid, but when I use the cisco 3750 as my gateway after adding route maps for forwarding the internet traffic coming to the cisco 3750 to squid it disconnects me from internet as well I cannot even reach the switches from the corporate network. These are the only Lines I used for the routing:
!
route-map proxy-redirect permit 10
match ip address 110
[Code]......
View 6 Replies
View Related
