Cisco :: WCS 7.0.220.0 Database Export For NCS Migration?
Apr 14, 2013
I have done a WCS 7.0.220.0 to NCS migration prior to moving to Prime 1.2. I followed the instructions to export the WCS database via the export.bat all command and exported the database. However, when I import this zip fileto NCS there do not seem to be any of the original WCS templates. All the maps and AP details have migrated but no templates.
I have tried the export again and ploughed through the resultant zip file looking for anything that looks like template files but there is nothing immediately apparent that looks like templates.
View 6 Replies
ADVERTISEMENT
Apr 18, 2013
I'm trying to migrate old data from WCS 7.0 to Prime 1.2 ... I have already created the zip file from WCS and imported it into the defaultRepo on Prime. I see it in the directory when I do a show repository defaultRepo so I have confirmed that it is there. My issue is that it appears Prime 1.2.1.012 won't accept the cli command of ncs migrate.
how I can proceed with the migration? I haven't been able to find any similar command in the Prime CLI so at this point I'm lost as to where I should go from here. I really don't want to have to tell the customer they have to downgrade to Prime 1.1 in order for them to perserve their maps especially since the Deployment Guide for Prime Infrastructure states that it is possible to migrate date from WCS 7.0 to Prime 1.2 as shown below ...
Data Migration
#
Data can be migrated from WCS 7.0, NCS 1.1, or LMS 4.x. More details on migrating data from each of these applications are spelled out in the following sections.
[Code].....
View 10 Replies
View Related
Apr 1, 2013
I installed a chained SSL cert on our anchor/guest 4402 a few years ago.We now have a need to replace the 4402 w/ a 5508, and I got everything configured, ready to go, except that darn cert.I can no longer locate the private key that was used to sign the original CSR.Is there any way to export the current cert from the 4402, so that I can import to the 5508? Or am I SOL?
View 3 Replies
View Related
Oct 2, 2011
Got an problem with LMS 3.2/Solaris.
See no devices both in DCR and RME, besides, in RME device counters (Normal/Pending/etc) are equal to current device count, but then you try to select them for any operation, you unsucceed - 0 device selected, no list of devices, unable to export, no ability to do anything.
Upgraded to 3.2 SP1, no change. Spend a lot of time digging through logs at /usr/adm/CSCOpx/logs, find no problems at all. Seems, that some database parts were corrupted.
I decided to reinstall LMS from the scratch, but to do so I need to export the DCR device data and credentials.
Database is alive (dbaccess.pl install going smoothly, then connection with user lmsdatafeed works and allows to connect and select data from any SQL tool), but this view is not enough for getting from the DCR both device data and credentials.
I have the DB password I set up during installation.
Is there any way to get data I need connecting to LMS database directly with some kind of sysdba SQL database user?
View 3 Replies
View Related
Mar 14, 2011
I'm moving from a 5505 to a 5520 and moving to a different location. I have a certificate on the 5505 that I want to export to the 5520.Can I export that key/certificate and import to the new ASA? Is there a problem since its a different location with a different IP ? (Domain name is the same, I moved the name on the DNS also)Do a have to re-do the signing process with the CA ?
View 3 Replies
View Related
May 10, 2011
I am trying to export our network devices from ACS and I can't find out where it is exporting it. Under ACS 5.2 "Network ResourcesNetwork Devices and AAA Clients" you get the list of your network devices and at the bottom of the page there is an export button. When you click it you are given an option to password protect it which I didn't check the box and I pressed Start Export. The window flickers like it processed the request, but nothing happens. There isn't any pop-up to download the CSV. I have also tried setting up a software repo thinking it might just send it to that, but it didn't work either.
View 2 Replies
View Related
May 14, 2013
This feature is not working on our LMS installation. I have tried different browsers but is always giving the same error. It seems to be Java related.
View 0 Replies
View Related
Jul 25, 2012
How to export Air Quality reports from a 5508? I'm pretty sure I have read that we can not look back in time at the Air Quality report from the WLC, but can from NCS. If NCS was in the picture, can the Air Qaulity Report somehow be exported?
View 3 Replies
View Related
Oct 12, 2012
cisco 2651XM router with WIC1 adsl card and NM-16ESW switch
IOS: c2600-ipbasek9-mz.124-23.bin
I use the following config to export traffic from the adsl card to a fasterthernet port so I can look at the adsl traffic in wireshark on a pc:router(config)#ip traffic-export profile my_rite router(conf-rite)#int FastEthernet 0/0 router(conf-rite)#bidirectional router(conf-rite)#mac-address abcd.efgh.ijkl (mac address of PC) router(conf-rite)#exit router(config)#int dialer0 router(config-if)#ip traffic-export apply my_rite this config works and I can see stuff going on in wireshark but it's only one way. This config only shows traffic going out from my adsl card, but no incoming. There is defintely traffic going both ways because everything about my adsl connection is working perfectly. I've tried using a different fastethernet port, even tried exporting to a different pc but all I see is outgoing ie: source is my public ip address but never as destination . I have bidirectional in the config but it still only shows outgoing. I even tried a different IOS (c2600-adventerprisek9-mz.124-15.T8.bin) but still it doesn't show incoming traffic. Could it be my ISP in some way hiding incoming traffic from view?
View 3 Replies
View Related
Mar 1, 2012
Creating several Inventory-Report Templates via Report Designer I was asking myself how to export/import these templates for use on other systems, performing backup.
View 1 Replies
View Related
Mar 7, 2012
I am using a Thrid party NetFlow tool, Enabled NetFlow on the Cisco 6500 as per recommendations and getting only half amout of traffic passing thorugh the interfaces. I have verified with 3 different NetFlow based tools, everything showing the same value. Is there any bug in my Cisco 6500.
View 2 Replies
View Related
Sep 19, 2012
I´m wondering if it`s possible to export the defualt web auth portal(web login page) via tftp to a computer from the Cisco WLC 5508 and then modify it and then import that customized portal to the WLC 5508?
View 6 Replies
View Related
Nov 29, 2011
I want to export the ACS local user's records.Then import to other ACS5.3 server.But the export file not the user's password record.I cannot import it well....
View 1 Replies
View Related
Oct 14, 2012
I have new ASA 5520 units currently we are using ASA 5510... I have to migrate all the configuration to the new ASA 5520 units....I am wondering is there a possible way to export and import certificates from ASA 5510 to 5520....
how to export or copy all the configurations, plug-ins, certificates from 5510 to 5520.Existing configuration snapshot...CA certificates from third party installed for authentication and identity certificate from Verisign
WebVPN
Anyconnect
Plug-ins
IPSEC tunnels
NAT
View 1 Replies
View Related
Apr 25, 2011
We are trying to sniff traffic in one of our routers 2811 IOS 12.4(3f) capturing data into the flash memory and tftp later to one of our servers. We had followed the command procedure as it is indicate in Router IP Traffic Export Packet Capture Enhancements doc but it seems that the mode capture option is not alllowed in my router. My question is Why? I had read the doc and the hardware and software should support this feature.
ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)
yourname uptime is 2 weeks, 4 days, 22 hours, 14 minutesSystem returned to ROM by power-onSystem image file is "flash:c2800nm-ipbase-mz.124-3f.bin"
Cisco 2811 (revision 53.51) with 251904K/10240K bytes of memory.Processor board ID FCZ104174196 FastEthernet interfacesDRAM configuration is 64 bits wide with parity enabled.239K bytes of non-volatile configuration memory.62720K bytes of ATA CompactFlash (Read/Write)
View 4 Replies
View Related
Jul 22, 2012
I have an ACS applicance that had a version 5.1 and i did an upgrade to 5.3 with latest patch.For some reason, the runtime process got stuck in (reinitializing and restarting) state.i did the recommended action to perform ACS stop and ACS start and even hard reset of the appliance, but it did not cut itThis process turned out to be a bug and it should have been fixed in version 5.3, but it has not i guess
i know that acs reset-config will solve the issue, but i have a problem here , the license file will be deleted as well with the config and i cannot find a way to export the license and then import it into the reseted config ACS hardware. Unfortunately, the license file is not saved anywhere in the company and i cannot affort to lose it.how to export the license from the applicance (CSACS-1120)?
View 3 Replies
View Related
Mar 21, 2013
I have three ASA5505, two firewalls connected to central VPN hub. the central inside network is 192.168.0.0/24,Network A is 192.168.1.0/24,Network B is 192.168.2.0/24,In one of this site (central), I have server with NetFlow collector.,I will collect the traffic information from all ASA at the my one serverCan I configure source IP address (or source interface - inside) for NetFlow packet, originate from ASA? (for example from site A)If it is not possible I think, I can rewrite my access lists and permit udp traffic from outside interface to server IP like this:access-list VPNACL permit udp host <Outside IP site A> host <Inside IP the Server> eq 9996,But I do not understand, what port I must be use in access list on Central site ASA. ,access-list VPNACL_A permit udp host <Inside IP the Server> host <Outside IP site A> eq 9996 ? or, in this place, must be source port in the udp netflow packet?
View 2 Replies
View Related
Nov 3, 2011
To enable netflow export on ASR1001, do i need the firewall feaure license or not ?Docs are not really clear, NBAR requires FW license, but i am unsure about Netflow?
View 1 Replies
View Related
Apr 15, 2010
I try to export a Detailed Device Report to a CSV. It failes:
<HTML><META HTTP-EQUIV="content-type" CONTENT="text/html;charset=utf-8">
<H1>HTTP Status 500 - </H1><HR SIZE=1 noShade>
<P><B>type</B> Exception report</P><P><B>message</B> <U></U></P><P><B>description</B> <U>The server encountered an internal error () that prevented it from fulfilling this request.</U></P><P><B>exception</B>
[code].....
Exporting to PDF works OK.CW is running on Windows server. RME is 4.3.1
View 11 Replies
View Related
Jan 26, 2012
When I attempt to export the certificate for the quickvpn client via the router web interface, it looks as if the export works, and it asks me to save the zip file. However, upon opening the zip file I receive the error: The compressed folder is invalid or corrupted.
This happens in multiple browsers, from multiple machines.
View 1 Replies
View Related
Jan 3, 2012
trying to export WCS data in order to migrate to the NCS but getting bellow error messages while following the Exporting WCS data doc:
D:Program FilesWCS7.0.172.0in>export D:wcs.zip
Error occurred during initialization of VM
Could not reserve enough space for object heap
Could not create the Java virtual machine.
The procedure i am tring to follow:
To export WCS data, follow these steps:
#Step 1 Stop the WCS server.
#Step 2 Run the export command through the script file and provide the path and export file name when prompted.
#Step 3 For Linux, run export.sh all /data/wcs.zip. For Windows, run export.bat all datawcs.zip.
I do have enough available space, the WCS runs as VM
View 7 Replies
View Related
Jan 15, 2013
I've seen a discussion about importing mac addresses into the mac filter db on a cisco controller but is there a way to export the mac filter db? I have a Cisco 5508.
View 2 Replies
View Related
Dec 19, 2012
I've got a WLC5508 (7.0.116.0) that is managed by WCS (7.0.172.0). I set up another WLC5508 with the same code and managed by the same WCS. Now I'd like to export all the 800 guest user accounts with the passwords from the old WLC and import them into the new WLC.
View 10 Replies
View Related
Jun 13, 2012
I have inherited a working but ancient Win 2000 DNS/Web Server on a T1 line and need to update it to a more modern Linux system. Is there a relatively easy way to export the windows configuration to a Bind config that I can modify?
View 1 Replies
View Related
Feb 14, 2012
how to export objects (net and security) from an ASA 5500 firewall to a .csv file?
View 1 Replies
View Related
Nov 24, 2011
i was connected to my rv042 via remote management / browser, and tried to add vpn clients. i generated a new certificate and then i clicked on export for clients. by doing this, the remote management disconnected and i cannot access the router anymore.
how can i get the new .pem file from remote? do i have to make somebody turn off and on the unit to get back remote access??
p.s.: after turning off an on i tried the same steps again: everytime i click on "export for admin" or "export for client", this kills the remote management and the unit must be hardreset. now: how do i get the newly created client certificate off that unit ?? otherwise i will have to drive 350 km just to grep that file ?!?!
View 1 Replies
View Related
Mar 13, 2012
I have a problem with the 6500 not exporting netflow data. They are not exported due to no fib.I have read somewhere that this has something to do with VRF. VRF are running on the router.ip flow ingress has been applied to desired ip int.Is there anything I could do to make it export netflow data?
VSS-core-XXX-rs1#sh ip flow export
Flow export v5 is enabled for main cache
Export source and destination details :
VRF ID : Default
Source(1) xxx.xxx.83.253 (Unknown)
[code]....
View 7 Replies
View Related
Jan 19, 2012
Does the Cisco WS-C3560X-24P-S switch supports ip flow export?
View 1 Replies
View Related
Aug 28, 2012
Is it possible to have one netflow export profile (may not be the right word...) to send all the flow information to one collector and another profile to only send traffic to and from centain IP addresses to another collector? If it is possible on the hardware and software, any quick sample config?
#sh ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH4,
#sho module 7
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
7 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1115LJBR
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
7 0017.9444.9814 to 0017.9444.9817 5.3 8.4(2) 12.2(33)SXH4 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
7 Policy Feature Card 3 WS-F6K-PFC3B SAL1115L2NH 2.3 Ok
7 MSFC3 Daughterboard WS-SUP720 SAL1115LH7W 2.6 Ok
Mod Online Diag Status
---- -------------------
7 Pass
View 2 Replies
View Related
Jan 8, 2013
I am working on Cisco 3550 switch on a certain requirement. I have got an access point connected to the switch and few mobile phones connected to the access point. I get the list of mac addresses connected to the switch ( Both access point's mac address & the clients addresses) by "show mac-address table dynamic" command. However, i am unable/confused to get the output of the following scenarios:
1. I would require to export the mac address from the switch to the local machine in any format (May be by using an SNMP tool, if available) so that the same needs to be used in my C# for development.What would be the way for the same ?
2. The mac address in the mac address table doesn't get updated dynamically. (Eg Scenario: A wifi client gets connected to an access point which inturn is connected to the switch, the mac address of the client shows up in the switch table. However if the client is disconnected, the client's mac address would still be displayed in the switch table )
View 9 Replies
View Related
Aug 16, 2012
How do I, if I even can, adjust the MAC table timeout from 5 minutes to whatever is bigger and allowable?
I would like to also like to change the ARP table timeout as well.
View 4 Replies
View Related
Jan 26, 2012
I need to generate an ODBC connection to the upm Datasource on LMS 4.1 running on Win2K8. I have successfully built connections to cmf, ipm and rmeng, however UPM keeps failing saying that the Database is not found.
Here are my settings.
Driver = CiscoWorks Embedded Database
ODBC Tab - Data source name = upm
ODBC Tab - Description = Device Performance
Login Tab - Supply user ID and Password is selcted
Login Tab - User ID = lmsdatafeed (i have tried DBA as well)
Login Tab - Password = set using the password I estabplished with the dbaccess.pl and dbpasswd.pl scripts
Database.Server name = upmEng
Network.TCP/IP = HOST=<lms server ip>;DOBROADCAST=NO;ServerPort= 43800
I validated the server port using netstat -a -b -o and matching up the PID with the UPMDBEngine process shown in the LMS Manage Processes window.Windows firewalls on the remote machine and the LMS server are off.
View 3 Replies
View Related
Sep 22, 2011
what is the database to use cisco LMS3.2 and how to access the database?
View 3 Replies
View Related
