How to export Air Quality reports from a 5508? I'm pretty sure I have read that we can not look back in time at the Air Quality report from the WLC, but can from NCS. If NCS was in the picture, can the Air Qaulity Report somehow be exported?
View 3 RepliesCreating several Inventory-Report Templates via Report Designer I was asking myself how to export/import these templates for use on other systems, performing backup.
View 1 Replies View RelatedI try to export a Detailed Device Report to a CSV. It failes:
<HTML><META HTTP-EQUIV="content-type" CONTENT="text/html;charset=utf-8">
<H1>HTTP Status 500 - </H1><HR SIZE=1 noShade>
<P><B>type</B> Exception report</P><P><B>message</B> <U></U></P><P><B>description</B> <U>The server encountered an internal error () that prevented it from fulfilling this request.</U></P><P><B>exception</B>
[code].....
Exporting to PDF works OK.CW is running on Windows server. RME is 4.3.1
I've seen a discussion about importing mac addresses into the mac filter db on a cisco controller but is there a way to export the mac filter db? I have a Cisco 5508.
View 2 Replies View RelatedI've got a WLC5508 (7.0.116.0) that is managed by WCS (7.0.172.0). I set up another WLC5508 with the same code and managed by the same WCS. Now I'd like to export all the 800 guest user accounts with the passwords from the old WLC and import them into the new WLC.
View 10 Replies View RelatedI´m wondering if it`s possible to export the defualt web auth portal(web login page) via tftp to a computer from the Cisco WLC 5508 and then modify it and then import that customized portal to the WLC 5508?
View 6 Replies View RelatedI've been asked to generate some report data on a specific WLAN, a limited access WLAN that was added recently. We need to be able to report on "Average and Peak Number of clients (Total)" and "Total Bytes Transferred (all APs)" on a per site basis. The sites involved mainly use 4402 and 5508 WLCs managed by our WCS server. Is there anything on WCS where we can easily get this information (on a monthly basis).
View 1 Replies View RelatedI took my router with me to visit family at Christmas. It wouldn't allow the wired computer through the switch, but yet I could talk to the router with my laptop. Rather than reconfigure, I bundled up my router & laptop and let well enough alone.Now that they're all back at my house, I can't reliably get the laptop to connect - Low Wireless Signal error. I've reset the modem & router repeatedly. Tried Channels 1,6, 11 and 8&9 too. n only, as that's my laptop's. On 2 occasions it has connected, rebooted and auto connected and run for 4-5 hours. Then it's gone. I've beat this mess for 3-8 hours per day, for days...!!!Laptop(Vista) connects to every other wifi I've tried. It's sitting 4 ft from the router.
misc. info.
separate dsl modem, Centurytel, Netopia Cayman 3300 series
no other devices beyond wired desktop and laptop
no changes in other neighboring networks
We have a UC500 with 3 access points AP541N. We need to move around the building so we use wireless voice with 7925G phones. All works fine except when the phone needs to change from one AP to another. We lost connection for a small interval of time and then resume normal operation.
View 1 Replies View RelatedI will be building my own computer here in the next month and am looking to become quite informed about building my own wireless network.Trouble is, I'm a bit out of to with what I need and what is good. I'm also officially tired of renting a modem from Comcast (bastards keep bumping my monthly rate up). So what pieces of equipment do I need to build a simple quality wireless network for my home? I would like the network to support two laptops, one desktop, and an Xbox plugged into a LAN line. Also, I'm thinking of using a Rosewill Wirelss Adapter 3 antenna [URL].
View 4 Replies View RelatedBought the new EA4500 a couple of days ago and have looked at my wireless connection and see it varies from 72Mbps to 144Mbps. It has jumped up to 270Mbps a few times, but rarely. Shouldn't it be 300Mbps most of the time? My laptop is 4 feet away from the router and the router is on top of a card board box being elevated away from interference. The prior router was a dlink 855 that went whacky after 3 years. I believe I was usually at 270 Mbps with that. What gives? Do I have a faulty router? With this new router, I expected the range to be a lot farther and faster too, but it is not in my family room. 2nd floor router, family room is 1st floor about 50 feet away and I get 1Mbps - 5Mbps. Everything is set to Auto on router and IP6 is disabled on laptop.
View 9 Replies View RelatedI use in my network Linksys 4200v1 (newest firmware) and Sipura SPA 3000 ( 3.1.20(GW)firmware) and SPA 122 (1.1.0(011) software version as my phone adapters.My voip phones are working great until I start to download or upload some files, watching on-line tv.How and where should I set up above routers to have the same great quality voip while uploading and downloading at the same time?
View 4 Replies View Relatedtrying to export WCS data in order to migrate to the NCS but getting bellow error messages while following the Exporting WCS data doc:
D:Program FilesWCS7.0.172.0in>export D:wcs.zip
Error occurred during initialization of VM
Could not reserve enough space for object heap
Could not create the Java virtual machine.
The procedure i am tring to follow:
To export WCS data, follow these steps:
#Step 1 Stop the WCS server.
#Step 2 Run the export command through the script file and provide the path and export file name when prompted.
#Step 3 For Linux, run export.sh all /data/wcs.zip. For Windows, run export.bat all datawcs.zip.
I do have enough available space, the WCS runs as VM
there is a line set with a provider with EoMPLS.This is an international line coming with 10M connectivity.the line is working fine with udp traffic but with tcp we don t get any use more than 1M.
View 7 Replies View RelatedI recently swapped a EA4500 for an EA6500 and have been experiencing intermittent Internet connection issues, specifically periodic disconnects (as some other users have reported). The router is connected to a Motorola SB6121 Cable Modem with Comcast as the cable provider. I contacted Comcast and they specify 1500 as the MTU size. With the Router set to Auto, I experience the periodic disconnects. When the MTU is manually set, I still experience the periodic disconnects, and I noticed that a ping test specifying the packet size with the -l switch results in a fragmented packet and is only resolved when the ping packet size is reduced by 28 bytes. Thus, it appears that the MTU specified on the router fragments all packets of that size and up to 27 bytes less than the MTU setting. For example, with the MTU set to 1500, all packets 1473 or larger are fragmented; with the MTU at 1444, all packets 1417 or larger are fragmented. I believe there is a bug in the current firmware, which I have installed on this router as version 1.1.27.141816. Regardless, even with the router set to Auto, the correct packet size is not properly detected and di
View 9 Replies View RelatedI have a ea4500 router with 3 pc's, 4 iphones, 2 playstations, ipad, ps vita, house cat, and a printer all wired into the internet. There are four of us in the family all using the internet but I suspect one of us is using considerably more than the other. I live in the country and my current isp has us on the max available account - 50 gigs / month. Lately we have been hitting 45 in less than 3 weeks into the month. I would like to know which of the things connected or which person is using the most of the bandwidth up. Is there a program that doesn't require a phd in quantum physics and networking that can monitor this for me and spit out a report.
View 9 Replies View RelatedI am trying to figure out how to setup quality of service on my network. At the moment i have computers connected to the PC port of my IP phone and the IP phone connected to the switch.I want the PC to stay on the default native VLAN and the phone to go on the VLAN 10I am using SNOM300 and SNOM360. I will configure the on the phone the VLAN ID and the priority.From my research, there are two ways that I can go about this on the port that is connected to the phone I canswitchport voice vlan vlan-idorswitchport voice vlan dot1pand then I will have to execute the commandmls qos trust cosmy question is which command do i use to configure the ports, and am I on the right track? Also, this is how I configure the ports that the IP phones are connected to, how do I configure the port that my Asterisk PBX server is connected to?
View 4 Replies View RelatedWe are having issues transferring a 200GB VHD file across our point to point without being corrupted in the process. Any good application for testing the line quality across the point to point?Preferably we want something free, but if there is an in depth tool that costs money, we are open to that option as well.
View 1 Replies View RelatedAny good suggestions for a quality wifi adapter ? Everything I've used so far has been terrible.
View 1 Replies View RelatedI'm in charge of the IT of a dorm with 200 inhabitants. A lot of people complain about the bad quality of "skype-calls". Audio is delayed and video stucks. The actual speed of our internet connection should be fast enough so I guess it has something to do with the QOS setting. I checked it on our WLC 3750 and right now we use Silver (best effort). Could there be any improvement when I set it to Platinum?
View 15 Replies View RelatedI am facing Voice Quality issue in Cisco Ip phone. However I don’t have any issue while calling between extension in the same Site. I am facing voice quality issue while traffic flowing through the MPLS over GRE tunnel. Its working fine If I am removing the mls Qos in Cisco 3550 Interface.
[Code]....
I have a client using a VOIP service to a third party provider (RingCentral). They are connected via Cable ISP (6mb) to the Internet and now experiencing performance issues with their VOIP service. They indicated that the call can be heard but that there is jitter and choppines in the call and they have to place a regular landline call. Their provider recommended using QOS to improve. I did not see anything straight forward on the ASDM interface to do this and figure it may require command line to accomplish.
They have Cisco IP 303 and 5252G2 phones which connect through an ASA5505 7.2(4) to their provider for service. Apparently the voip app uses the following ports:
UDP
5060-5090
8000-8200
16384-16482
What would be the best solution to improve performance or perhaps traffic shape / priortize traffic to work. I assume this may be happening if there are heavy downloads or activity happening on the network. The ASA5505 is on 7.2(4). Some coded examples for the above info.
I have a wireless router on the ground floor of my home which is wired to my PC on the 3rd floor. The wifi signal is of poor quality on the 3rd floor. I cannot move the router to a different floor since all of my connections are wired through the home into my networking room (on the ground floor where my router is). I wish to add a media receiver to a different room on the 3rd floor that is not wired already for networking. Streaming video files wirelessly to the media receiver from my router will not work because as stated previously the signal quality is poor on the 3rd floor. My mobo on my computer has ASUS wifi GO. Can I enable the wifi go on the mobo of my PC (located on 3rd floor) to connect to the media receiver (also on the 3rd floor) for streaming? The media receiver will also have an internet browser so will I be able to connect to the internet as well if it is networked to my PC and my PC is connected to my router on the ground floor?
I basically want to keep my PC connected to my main router for high DL speeds and also have my PC networked wirelessly to my media receiver using the on board wifi go. If possible I'd also like to be able to access the internet on the media receiver via the PC.
I'm considering using this cam as a live cam pointed across the street to a beach and ocean view. Would it produce a decent video if used for this purpose? I've been looking around for some sample video from this cam but so far no luck. Any sample sites I could log into to see the 930l in action?
View 3 Replies View RelatedHad problems with voice quality on VoIP with 4500 series switches and the qos dbl feature (which gets enabled by the auto qos feature)?? I have had a couple of customer complaining about voice quality and our voice team spent a lot of time investigating; I had ruled out the network infrastructure because it was all QOS enabled. The voip people came up against a blank so I looked at the network once more and disbaled dbl with hope more than anything else. Mysteriously the voice quality issues the customer was having have now disappeared. Not sure whether a coincidence (though I have done this on two customers now) or something to with with dbl. There is nothing on this on cco.
View 3 Replies View RelatedWe have branches all over the country and we take different links like fiber (Ethernet) radio links etc. Now sometimes when we ping from branch WAN ip to its gateway or to the aggregation router (ASR 1000) in this case, we see some drops, but see no problem in actual HTTP or lotus communication.
What i want to know, that now a days, should we rely on ping results to determine link quality ? or should i use tools like iperf to basically see if the link is actually treating tcp and udp packets properly, I have heard this countless times that normally network devices like Cisco routers, even without any QOS, will give low priority to ping packets.
I tried multiple times to register a username here and no matter what I chose I would only get "An Error Has Occurred" when I submit the info. I've tried this over several days and keep getting the same dead end. So, I went to bugmenot.com and I'm using a generic username that was given there in order to post this. So...there's that...
Starter info... I'm running Hardware Rev A4 of the DIR-655 on the 1.33NA firmware. I never upgraded past that firmware because of all the horror stories I'd read about new firmware here. Up until lately it's been fairly stable. The issues I refer to SEEM to coincide with my recent installation of Apple TV hardware on my wireless network, though I can't confirm. It's never been great with this router, so that could be coincidental. On my network I have a hardwired Mac Mini, wireless Macbook Pro, a hardwired D-Link DNS-321 NAS box, Apple TV, Logitech Revue, iPad, iPod Touch, iPhone and occasionally one each of a Samsung and LG Bluray player (only when they're powered up, which is rarely). I'm also using a wireless repeater in the middle of my house because the DIR-655 doesn't yield a very usable signal in my master bedroom, which is on the opposite side of the house as the router.
With all that being said... I have had terrible issues being able to keep a steady connection wirelessly with this router as of late. Streaming Youtube videos will stop after a few seconds, loading websites will just stop responding all together, and I can't even keep a connection to stream music from my Mac Mini to my phone or AppleTV using Home Sharing in iTunes. I'll get a few seconds of a song and it will just drop out completely. It's been extremely annoying and I'm ready to take a hammer to this router, to be honest.
I've checked my logs and there were all kinds of FIN:ACK, PSH:ACK and SYN:ACK TCP packets that are being blocked. I noticed many of them were coming from Apple IP addresses, so I assume that the AppleTV had a lot to do with those. I actually used the Inbound Filter settings to allow requests from a whole block of Apple IP's, which seems to have settled log items from them down a lot. There are still quite a few that seem to be coming from Google IP addresses (I presume the Logitech Revue since it uses the Google TV interface?), but the Google IP's are too random to go allowing a large block. [code]
I have Advanced DNS disabled. All Traffic Shaping and QoS boxes are checked to enable. Comcast is my cable internet provider. I've noticed that my WAN Connection Up Time is often a fairly low number like the connection to the cable modem drops out frequently.
I'm trying to migrate old data from WCS 7.0 to Prime 1.2 ... I have already created the zip file from WCS and imported it into the defaultRepo on Prime. I see it in the directory when I do a show repository defaultRepo so I have confirmed that it is there. My issue is that it appears Prime 1.2.1.012 won't accept the cli command of ncs migrate.
how I can proceed with the migration? I haven't been able to find any similar command in the Prime CLI so at this point I'm lost as to where I should go from here. I really don't want to have to tell the customer they have to downgrade to Prime 1.1 in order for them to perserve their maps especially since the Deployment Guide for Prime Infrastructure states that it is possible to migrate date from WCS 7.0 to Prime 1.2 as shown below ...
Data Migration
#
Data can be migrated from WCS 7.0, NCS 1.1, or LMS 4.x. More details on migrating data from each of these applications are spelled out in the following sections.
[Code].....
I installed a chained SSL cert on our anchor/guest 4402 a few years ago.We now have a need to replace the 4402 w/ a 5508, and I got everything configured, ready to go, except that darn cert.I can no longer locate the private key that was used to sign the original CSR.Is there any way to export the current cert from the 4402, so that I can import to the 5508? Or am I SOL?
View 3 Replies View RelatedI have done a WCS 7.0.220.0 to NCS migration prior to moving to Prime 1.2. I followed the instructions to export the WCS database via the export.bat all command and exported the database. However, when I import this zip fileto NCS there do not seem to be any of the original WCS templates. All the maps and AP details have migrated but no templates.
I have tried the export again and ploughed through the resultant zip file looking for anything that looks like template files but there is nothing immediately apparent that looks like templates.
Got an problem with LMS 3.2/Solaris.
See no devices both in DCR and RME, besides, in RME device counters (Normal/Pending/etc) are equal to current device count, but then you try to select them for any operation, you unsucceed - 0 device selected, no list of devices, unable to export, no ability to do anything.
Upgraded to 3.2 SP1, no change. Spend a lot of time digging through logs at /usr/adm/CSCOpx/logs, find no problems at all. Seems, that some database parts were corrupted.
I decided to reinstall LMS from the scratch, but to do so I need to export the DCR device data and credentials.
Database is alive (dbaccess.pl install going smoothly, then connection with user lmsdatafeed works and allows to connect and select data from any SQL tool), but this view is not enough for getting from the DCR both device data and credentials.
I have the DB password I set up during installation.
Is there any way to get data I need connecting to LMS database directly with some kind of sysdba SQL database user?
I want to make packet sniffer which capture the IP packet and then extracting QOS filed from it's header
View 1 Replies View Relatedcapturing high-quality audio (44.1 kHz, 12+ bits) and send it over WiFi to a receiver.
Microphone->[Audio module+Transmitter] -> Wireless Link -> Receiver