I have a bunch of 1242 access points that we replace with 3500s. Does Cisco have a good program to reuse these devices? We tried trading them in but for some reason it never pans out.
View 5 RepliesI have a setup like this:
A central WLC 5508 running code 7.2 with management vlan 10 ( range 10.10.10.0/24), corp-user vlan 100 (10.11.10.0/24) with WPA2 key, guest vlan 200 (192.168.0.0/24, on local dsl modem) with WPA2 key...
A remote WLC 5508 with code 7.2 with management vlan 10 (range 10.20.10.0/24), corp-user vlan 101 (10.21.10.0/24) with WPA2 key and guest vlan 201 ( 192.168.0.0/24, on local dsl modem) with WPA2 key
corp ssid "Corp-user" on both sites
Guest ssid "Guest" on both sites
Intention is that the AP's (3500) on the remote site should fail over to the central WLC in case of any failure on the remote WLC and that the users could remain in their local vlan.
What kind of configuration would make this work?
I bought the EA6500 yesterday, to replace my E3200.Formerly, with the E3200, I was able to block applications on the router admin page, without blocking all internet access, under the "Access Restrictions" Tab. I could create access policies that allowed internet access to specific devices, while blocking port ranges/protocols for specific applicatons. while this didn't work for Skype, which jumps from one port to the other until it finds an open one, it worked perfectly for World of Warcraft. the primary target of my restrictions.in common with the old setup for the E3200, the new cloud login allows me to block internet access completely to a device. it also allows me to block websites to my heart's content, an improvement upon the old system, which stopped at four. but to my great surprise, it will not allow me to specify port blockages for specific apps for specific devices., while the new EA6500 is blessed with the added capability of actually recognizing applications by name, *it is only to give them greater priority*. the Media Prioritization tab lets you give a ton of your bandwith to specific apps, but won't let you throttle or block them. Is there some way to work around this? Some alternative firmware? again, I don't want/need to block all internet access to a particular computer. I only need to block some apps (World of Warcraft, and Skype, possibly some torrents) by closing some ports.
View 2 Replies View RelatedWe need to add additional APs to working wireless mesh network (WLC 4402, 1520 series AP).
WLC 4402 supports 1550 series access points with firmware upgrade to 7.0.235.0 :
[URL]
Is AIR-CAP1552E-x-K9 with three external dual band antennas enough for 2-GHz b/g/n local access and 5-Ghz back haul?
Does 1552 Mesh AP work with 1522 Root AP?
EA4500 Linksys router stopped allowing vizio Internet apps to connect from two different TV's. Problem, Just got brand new EA4500 router and Motorola SURFboard DOCSIS 3.0 High-Speed Cable Modem Model: 575319-019. I have 2 new vizio big screen tv's with internet apps. All was working fine and had no problems but occasional drops or limited access.
One day BOTH TV's could no longer connect. However, The tv's will connect to another access point. therefore the problem does not exist in the TV/s and has to be a problem in my access point (I.E. Router allowing access). Additionally, all other devices connect and work fine. I have already unplugged everything for an extended period of time. Checked for updates on firmware and verified no software needed to be updated. Rebooted router... Am using wpa-psk and feel i shouldn't have to go weep as it was working fine...
Recently purchased the EA3500 router. Everything seems to work great except for Facebook on mobile devices with Android OS using both apps and browser. I can access FB using a laptop's browser.
View 9 Replies View RelatedIs that possible to remove DFM and IPM from LMS 3.2 I have never used and LMS appears to be slow and i am thinking trimming some unwanted apps may work.
View 3 Replies View RelatedMaking Configuration between 2 Apps?
View 1 Replies View RelatedI have an interesting SVPN challenge that I'm asking the subject experts here to assist me in solving.A customer in Domain A wants to transmit data to Domain B. The customers have agreed to establishing a secure vpn connection from Domain A to Domain B to transmit real time data. The challenge comes from sending unencrypted data from nodeA to nodeB & nodeC withing an encrypted VPN tunned to node d.The challenge is sending non-encrypted data from NodeA to NodeB where an encrypted VPN session is active. Every time I attempt to configure the interface (AppC) the VPN session is terminated, and the interface can no longer "see" nodeD via IP mapping. An engineer recommended adding a second NIC card to NodeB thereby permitting control of the AppC even when the VPN is up and running.Can I send live non-encrypted data to NodeB data buffer, while AppC sends data to NodeD in a VPN tunnel ?
View 1 Replies View RelatedI configured ACE 4710 for HTTP traffic. All applications are running through real server. But when I run the same applications from virtual IP i.e through ACE. some applications are not running. Particularly applications having XML.
Is it ACE issue or Application issue. If it is ACE issue then how to troubleshot.
I am thinking about running some third-party unified communications apps under VMWare ESXi5 on a Cisco SRE 900 module. According to the Cisco docs, third-party apps are supported on these modules (see table below) but the app in question is NOT on Cisco's list below.
[URL]
Some questions:
1. As long as the third-party app is capable of running under VMWare/VSphere ESXi5, is there anything on the SRE that would prevent you from running this third-party app even though it's not on Cisco's list?
2. What is Cisco's policy on the use of third-party apps that are not on their list? For example, will they take a support call on the SRE running a non-listed app. (I don't want to void any sort of support contract through the use of a third-party app not on their list).
A few days ago i tried logging onto to League of Legends, and my net disconnected. Thinking nothing of it, i reset the router and tried again, to no avail. Then for the last few days i can't get on skype, LoL, or any other program that uses the internet. I can get onto websites and such( using firefox) except i can not load youtube videos, otherwise my internet disconnects for a minute or so.
View 1 Replies View RelatedWe have a 5510 ASA that was running 8.0 and were using it for clientless VPN access. Through this, we published bookmarks that linked to an internal Microsoft 2008R2 RemoteApps server, which users logged on to and then launched RemoteApps (basically being RDP sessions to apps on the server).All worked fine until we upgraded to 8.4 over the weekend and we now can't launch the RemoteApps. We can still login through the ASA, still click a bookmark to take us to the RemoteApps server's webpage, still then authenticate against the domain fine and still see the published apps. The problem now is when we launch the apps we get "this computer can't connect to the remote computer" messages and the app fails to launch. Nothing has changed on the RemoteApp server side, only the upgrade to 8.4.
View 2 Replies View RelatedWe have ACE module intergrated in cisco 6509 switch. We have performance issue for specific url while accessing through ACE, but it works normal when works with direct url.The users are getting error at middle of works , " applications are unable to get data ". We have configured http-cookie sticky like below, [code]
We are using two rserver in serverfarm and enabled port-80 services.
yesterday at 6:30 am my internet was working fine.yesterday at 7am it quits working.the computers through the house are 2 desktop PC's, one netbook, and one laptop.the 2 pc's connect to the router via a switch.the netbook and laptop use the wireless router.the wireless router is not specifically just a wireless router, it goes both ways (hardline and wireless)after 7am, the netbook still had connectivity to the internet via wireless even though my laptop did not.the internet is still connected to all of them, browsers like google chrome, firefox, and IE7 do not work. but just like a browser, steam's store will not load.here's the funny part, the netbook still had browsing ability until 7pm last night.we checked all the ip's and MAC addresses on the computers to make sure nothing was conflicting.nothing was.packets were coming in and out at normal rate but none of our browsers worked.we do have comcast, and my father told me that comcast gives you norton for free for using them.i have read on here that removing norton magically solves the problem but 3 of the 4 computers does not run norton. and i also do not see the logic behind this.we have also recieved emails from comcast exclaiming that they have reports of "bot emails" coming from our I.P.'s could this have been an attack on our network or some network virus?
View 5 Replies View Relatedhow can i unblock apps games in fb which are blocked by fortiguard security system
View 2 Replies View RelatedDoes anyone know of some off the shelf (commercially available) software that will set the DSCP field to something other than 0? Im looking to do some network testing using any off the shelf software, voip, games, whatever. I have already setup a traffic generator but my testing needs to encounter a more real life scenario. I have already tried many games, skype, gchat, etc. but nothing sets the DSCP field to anything other than 0.
View 4 Replies View RelatedI am wondering how to restrict access to certain applications; software and hardware via a router.
View 2 Replies View RelatedMy younger brother uses IDM to download files and it slows my Internet down to a crawl. I've tried reasoning with him but its not getting through to him. Is there any way I can use my router (bcz only I have access to it) to limit IDM?
View 5 Replies View RelatedThe other day I set up a firewall on my Cisco 1841 router, it all seems to work fine except for a few small problems. 2 wireless devices an iPhone and an Android tablet are having some problems with 1 or 2 apps. iPhone 6.0.1 Facebook app and the App store will not load Android tablet ICS BBC iPlayer and Google play app store wont load or play content. Both devices with their issue were working fine until the new firewall was installed. I’ve tried opening ports and adding ACLs but nothing seems to work. I’ve included my start up config. All other PCs, laptops, smartphones and iPads work fine.
Building configuration...
Current configuration : 5551 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
[code].....
The other day I set up a firewall on my Cisco 1841 router, it all seems to work fine except for a few small problems. 2 wireless devices an iPhone and an Android tablet are having some problems with 1 or 2 apps. iPhone 6.0.1Facebook app and the App store will not load Android tablet ICS BBC iPlayer and Google play app store wont load or play content. Both devices with their issue were working fine until the new firewall was installed. I’ve tried opening ports and adding ACLs but nothing seems to work. I’ve included my start up config. All other PCs, laptops, smartphones and iPads work fine.
View 3 Replies View RelatedWith this modem, can you hook up to the Linksys Smart Apps WiFi?
View 2 Replies View RelatedMy network has recently started acting very odd. Everything works fine as long as i use only 1 internet using application at the time but my whole wireless network brakes down when i start up 2 internet using applications at the same time. Let me elaborate.
View 3 Replies View RelatedI have a Netgear WNR3500L wireless router. I assume it's v1 because on the back it doesn't have "v" anything. Firmware version V1.2.2.44_35.0.53NA.When I connect using g I get 22+Mbps download speed. When I connect using n I get 10 Mbps. I've tried using both WPA2 only (laptop reports 130 Mbps connection I believe) as well as the combo WPA+WPA2 (laptop reports connection of 117 Mbps).Broadband download results don't change - they stay at the 10 Mbps level. I've fiddled with some of the settings on my laptop's wireless card - but the results are the same.For now I'm just trying to figure out where I should focus my investigation and fiddling efforts - on the laptop or on the router.
View 5 Replies View Relatedi have a Netgear N600 Wireless ADSL2+ router on wireless a/b/g/n dual band and all that but what i want to know is will i get better performance if i use a WirelessN card over G on a 10 - 15mb/s connection gaming wise and will it b a great increase over the G causeif its not a HUGE increase then i wont waste my money on a newer card?
View 3 Replies View RelatedMy Acer Aspire 5610Z laptop will automatically connect to public hotspot wireless network but when I attempt to connect to a wireless network at home, set up using a Netgear modem, I only ever get 'local' internet connection only. My wife's HP laptop has no problem making the home wireless connection.
View 6 Replies View RelatedI am running windows vista and have installed the software and windows sees the adapter and states it is working but when it searches for available networks it can't find any. How can I download the driver and install it?
View 1 Replies View RelatedI have a setup involving 3 clustered AP541 running off a sg300 switch. The wireless network setup VAP has one entry for vlan 1 with station isolation disabled. Is there anything more I need to do to allow one wireless client to ping another wireless client - am I missing something - i assume this is possible.Needless to say wireless clients can ping non wireless clients and vice versa quite happily. Everything is running with factory default settings more or less.
View 4 Replies View Relatedoutput are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
I have a WLC 5508, AIR-LAP1142N APs and a SSID for students to connect to who bring their own device. I am still testing this and it has not been rolled out but I am running into some serious issues with joining the network. I am authenticating them through a RADIUS server (2008 R2). Problem: many of them cannot connect because they are lacking the certificate.
1. What is a good setup for authentication in a BYOD environment
2. If my setup is good what can I do to allow kids to use their computers on the wireless either without the certificate (which I know is unlikely) or what do I need to have them do to connect. I am hoping it does not involve hard wiring and getting the certificate from the server.
have a Cisco 5508 controller (version 6.0.199.4) that when I enable global multicast mode it will work for an hour or two and then it will kill the network. All internet both wired and wireless, access to server everything dead. I then have to directly connect to the service port and disable the global multicast mode. Then two reasons for enabling it are Docs2Go and LanSchool both require multicast to be enabled. I have it enabled on our wired network and it works OK there. ted.
View 10 Replies View RelatedWe have recently been given this unusual task. The setup is a series of CAP3502P access points, and a wireless controller (either 2500 Series or 5500 Series), as well as other standard network infrastructure.
In this network, the client (mobile/wireless) devices must be able to detect when they change what access point they are communicating through, while also requiring a seamless transition. Ie, if the client device is communicating via access point A, and displaying the application menus for A, when the user walks to the area services by access point B, it must detect that sot he application can display menus for B, without the user having to select "B".
Is there a way for the client device to detect which access point it is using and provide that to an application? Or alternatively a way for a host service residing on a server to get that information from the wireless controller?
i am placing a formal request to Cisco and to the firmware development team to create a new-and-improved firmware release for the WET200 wireless Ethernet bridge, a product that is still being produced, shipped, and sold. I purchased the product about one-and-a-half years ago and have enjoyed its performance. There have been, however, some flaws with the device, namely the following:While configured to use WPA2-based security, DHCP-related traffic is not passed from a router/gateway's DHCP Server to connected devices on the WET200. Current firmware release notes indicate this was a known issue and was, supposedly, fixed; however, due to the level of problems customers are reporting, it appears this may have only been resolved, if at all, with security configurations of WPA, WEP, or OPEN. It has not been fixed for customers using WPA2-based security.When I originally purchased the WET200 and configured it to use WPA2-based security, while it, initially, did have a few problems connecting to my router/gateway, it, eventually, did connect and stayed connected for, approximately, one year. However, in September of 2009, it suddenly lost connectivity with my router/gateway and has not been able to establish a connection since, even after reinstalling the latest firmware revision and after several soft and hard resets of the device. I tested the WET200 with another router/gateway, only to experience the same issue. Other devices are connecting to my router/gateway, but, not the WET200. The last firmware update for the WET200 was dated back in July of 2008. Currently, it is January 2010 and since these issues have been known for quite some time, it is unacceptable that the firmware for this device has not been updated in such a long time, especially when there are known issues with the WET200's firmware. Such lack of support is forcing me and my clients to stop using these Cisco-based products and purchase competing hardware, something I would prefer not to do; however, without better support, I and my clients do not have a choice. Expecting me and my clients to use an inferior form of security on the WET200, such as WEP and/or WPA, until a firmware update is issued is unacceptable, especially when that update has not been released in over one-and-a-half years. Such lack of support is especially unforgettable when my clients and I are looking to purchase new networking equipment. In the past, I would not have hesitated to purchase a Cisco-based product; now, with this experience in mind, I am finding it very difficult to recommend to a client that he or she should invest their organization's finances into Cisco-branded equipment. Proper, professional, timely, support of your hardware is expected of your customers, especially if you wish them to remain loyal customers. I have noticed that other similar devices, albeit, higher-end devices, have had their firmware updated, more recently, compared to the WET200. I assumed this meant that the firmware development team was updating all firmware on such devices. So far, I have been disappointed in the lack of firmware updates for the WET200. While I understand the possible desire to update the higher-end products, first, as a professional whose job is to research, recommend, purchase, install,configure, secure, and maintain both the enterprise-level and small business-level devices, I highly encourage Cisco not to overlook their small business products when the firmware development team is updating firmware for any Cisco products. Deficiency in the support of one strata of Cisco-based products is reflective upon the support of any Cisco-based product and is not easily forgiven by Cisco customers, such as myself, when new and additional hardware needs to be purchased.
View 15 Replies View Related