Cisco Wireless :: 4400 How To Configure Controller In Case Ethernet Port Goes Down
Oct 7, 2012
I want to configure a Cisco Wireless Lan Controller (4400 and 5500 series) with to data ports for failover? I think the primary and secondary ethernet connections should be configured as trunks. I cannot find anything on CCO about this or on the internet per se. I know how to configure for failover with APs but cannot find anything on how to configure the controller in case an the ethernet port goes down.
View 7 Replies
ADVERTISEMENT
Jun 7, 2011
I know how to access the GUI from the service port. However, I am not able to access from Port 0. IPs have all been properly set. We have a management VLAN in our enterprise. I have configured the WLC management interface for an ip on that subnet. Port 0 is connected to a 3560G switch. I have set the switch port to be an access port to the management vlan and I have tried to set the switch port as a trunk, with the native vlan set to the management vlan. I am not able to ping nor access the web GUI remotely via the management vlan.
View 3 Replies
View Related
Jun 2, 2013
We have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies
View Related
Apr 4, 2012
I have a Cisco 857 router which i used for Internet connection with RJ11 connectior (ADSL0 POTS) but now the ISP has changed the internet link with PPOE type and the ONT connection is RJ45 , Is there a possibility to configure one os the Fast Ethernet ports as WAN port for internet.
View 2 Replies
View Related
Jul 23, 2012
I have a Cisco Series 4400 WLAN controller and I'm trying to connect a lightweight AP to the controller. I have already assigned the switch port to use my wi-fi VLAN, and have connected the AP to the switch. After a few minutes, the light on the AP goes from green to light blue (indicating it's serving clients). When I log into he wi-fi controller to look for the Ethernet mac address of the new AP, I do not see its Mac Address. I want to be able to rename the AP to reflect where it will be used, but need to select the AP via its Ethernet mac address before I can make any edits like changing its name etc. I've gone through the "monitoring" menu, selected "All" and still do not see it in their via its MAC address. I also will select the "wireless menu" which lists all the AP's on my network, listing in order from on the longest running, to just powered on.Is there something I'm missing like a "re-scan" that scan's all devices?
View 5 Replies
View Related
May 19, 2013
I'm looking for a document that states the best practices for WLC configurations (Management/Security/AP's..etc). I can currently only find the following document:URL
But this document has last been updated in 2008, in a few days that's almost 5 years ago, and we all know how quickly technology is evolving. 10Gb wireless is around the corner, with 1GB starting to go production now. This document also mentions the 4400 (which is end of life).
View 1 Replies
View Related
Aug 2, 2011
I've download a login.html into the controller successfully, but when I preview the page there isn't an accept button. Do I need to create the accept button with the html file or is there some place I need to enable on the controller itself. After download the .tar file I reboot the controller but no luck. I also create a java script button redirect but it didn't redirect to where I needed to go. It just stuck on the splash page.
View 3 Replies
View Related
Jul 27, 2011
give me the run down on the features removed from the 4400 series in the 2500 series? Obviously 4400 is now EOL, and so i cannot purchase new. Therefore I was looking at the 2500 for my implementation to save costs also.I would like to have two SSID's, running seperate VLAN's, one voice, one guest, trunk the link to the AP's, which will be 1131AG or newer, N possibly. Voice needs to be encrypted with WPA or WPA2, guest needs to be open using the guest access feature. Here's a sample but with EAP:
[URL]
Is this supported to have WPA on one SSID and Guest access on the other? i did spot a paragraph in the 4400 manual stating that certain restrictions apply regarding one SSID having encryption and the other being guest mode?I notice also in the WCS documentation, it doesn't explicitly state it supports the 2500 series under the managed devices section?
View 1 Replies
View Related
Jan 22, 2012
Windows laptops that do not roam from one AP to another on the same 4400 controller? Particularly using an Atheros chipset - works fine under Linux... It's a WPA2/AES enterprise network on a controller running 7.0.220.0
View 4 Replies
View Related
Mar 7, 2013
I read the configuration guide about the 7.3 release. And I figured out that you will need a hash key for establishing a mobility group relation between a controller and a virtual controller. The 7.3 release for the 5500 series works fine for me.But the latest release 7.0.235.0 for the wireless lan controller series 4400 does not have a functionality to add a hash key while creating a new mobility group member.The command "config mobility group member hash" is totally missing. How to establish a mobility group between a 4400 controller and a virtual then ?
View 2 Replies
View Related
Sep 3, 2012
I read the configuration guide about the 7.3 release. And I figured out that you will need a hash key for establishing a mobility group relation between a controller and a virtual controller. The 7.3 release for the 5500 series works fine for me.
But the latest release 7.0.235.0 for the wireless lan controller series 4400 does not have a functionality to add a hash key while creating a new mobility group member.
The command "config mobility group member hash" is totally missing.
how to establish a mobility group between a 4400 controller and a virtual then?
View 4 Replies
View Related
Dec 19, 2009
We are facing an issue with a customer where a Cisco 4400 Series controller is blocking the 802.11a/n Radio Interface of a 1250 AP. The radio shows as down on the controller GUI. The error message on the GUI is that the 'Regulatory Domain' is not supported. This can be seen from the attached screenshot. Also relevant parts of the WLC configs are attached. WLC: Cisco 4402 WirelessWLC Country: SADevice: Cisco Lightweight Access Point 1250 (LAP) is controlled through the 4402 Cisco Wireless LAN Controller (WLC)The operating system version of the LAP: c1250-k9w8-mx.124-18a.JA version of the WLC: Software Version 5.2.178.0 The problem is that the controller shows that the 802.11a/n Radio Interface in Radio Slot # 1 is always down , the customer tried to manually 'no shut' the AP interface from the console and it worked , but obviously this solution would not work as the configuration cannot be saved (LW AP).
View 12 Replies
View Related
Aug 16, 2012
We have a Cisco 4400 series wireless controller deployed as a Guest Anchor in a private DMZ. We have 13 foreign controllers anchored to this for Guest Wireless. We recently anchored 17 additional controllers to this Anchor controller. Since we have done that, periodically on just 3 of the foreign controllers, the control path shows down on the mobility peer, then comes back up. We have had this issue in the past, but it resolved itself. However, now we are seeing this issue again. Are we reaching a limit on EoIP tunnels? I have read that there is a max of 71, and that is per controller, not SSID. We do have a firewall in the middle but all necessary ports are open.
We have had this issue for quite sometime, it just does not happen frequently. Since we have added the additional controllers, it is now happpening very often, but only with 3 controllers. There is not much in common with these 3 controllers. 2 are 4400 series, and 1 is a 5508. All 3 are local on a campus LAN, different networks. Could it have anything to do with memory or utilization?
View 15 Replies
View Related
May 20, 2012
I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.
View 10 Replies
View Related
Apr 10, 2013
we need to be required to import MAC filter databse from Cisco Wireless LAN Controller (4400) to Cisco ACS Server (v4.2).
View 2 Replies
View Related
Feb 14, 2013
We have one core switch and we are planning to add a 6509. Both are none VSS.All the access switches are Catalyst 3560 series.
We plan to have all 3560s to have a link to each of the core. Without VSS, it is not possible to etherchannel to both core switches correct?What protocol should I configure to prevent in case one core fails? HSRP, VRRP, GLBP?
Do I need to run spanning tree protocol? if so which one?What is the best way to connect from each Catalyst 3560 for load balancing and redundancy? One to each core?
View 4 Replies
View Related
May 28, 2012
We have two 4400 WLC's. We have around 20 access points in our network.If we assign controller1 as primary for half of the access points and controller 2 as primary for the other half, does this mean the association of the ap's indicate load balancing by the controllers. Does this mean wlc does load balancing as different ap's associate on different controllers. or does it only server as active-standby wlc.
View 2 Replies
View Related
Feb 22, 2011
When I try to import configuration from the controller 4400 to my WCS it gives the following message:
Status Refresh succeeded but some records were dropped because their key fields failed validations.
When i see the config in the WCS, all of my light access points are not on it. I check for the logs and this is What I get: (its a lot of info, so I am putting an example!)
02/23/11 14:18:46.784 ERROR [general] [TP-Processor7] THROWcom.cisco.server.common.errors.InternalException: [COMMON-1]: COMMON-1com.cisco.server.common.errors.ObjectNotFoundException: COMMON-
[code]......
View 3 Replies
View Related
Mar 6, 2012
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies
View Related
Jun 7, 2011
in one of the sites, the client has an exisiting 4402 controller which he moved to the DMZ in order to set it as an anchor & he purchased two new 5508 controllers to control the corporate APs. I configured all the parameters needed for the guest anchoring & then I tested the connection but there was an issue. (all the controllers are running the same firmware version)after testing the setup, the guest users could get an IP from the internal DHCP of the anchor controller (in DMZ), but then they cannot reach the internet or anything outside the anchor controller.Cisco confirmed that the 4400 is fully compatible with the 5500 to work in an anchor-foreign secnario as long as they are running the same firmware version. yet, when I temporarily used one of the 5500 controller in the DMZ as an anchor & I applied the exact same configurations on it as the 4400, it worked perfectly without any issues.
note: on the anchor controller (4400), the management & AP-manager interfaces reside on the same subnet & the wireless guest SSID is also mapped to the management interface. (may be this setup is causing the issue) but on the 5500 it is working just fine?
View 2 Replies
View Related
May 9, 2008
I am attempting to access the service port from a client pc on another network.
Service port = 10.100.2.1/16
Client IP = 10.1.1.10/16
I know you cannot put a default gateway on the service port, but the documentation says you can add a static route for remote management. So I tried...
config route add 10.1.0.0 255.255.0.0 <gateway.ip>
It does not take the command and says something to the effect of. "ip address/netmask conflicts with the configured ip address of the service port"
View 11 Replies
View Related
Jul 3, 2012
There is no "blinking light" indication on my E3000 at the Internet (Yellow label) and Ethernet port no 4. I tried plugging in 2 cables at all of the ports. I got the blinking indication at Port 1 through 3. The same cable's have no response at Port 4 and Internet port. As a result my I am not able to connect to the internet.
View 2 Replies
View Related
Apr 7, 2011
We recently reset a 4400 controller in a school. Although all access points associated, clients could not get the Internet. On investigating we suddenly lost connection to the web interface. We tried hyperterminal connections to reset, but found that the managament interface had the ports "unconfigured". We finally reset the configuration, and when we tried to start from scratch it now does not allow a port designation. It asks for 1 or 0 but says both are invalid when entered.
View 2 Replies
View Related
Jul 31, 2012
I had bued a WRP400-G2 device today and found 3 problems here (after upgrade firmware to latest). But biggest problem is that I can't open a bug case in TAC becouse I bued device from retailer and have only one year warranty. Is it possible to contact technical support of Cisco by email or Web site? It will be a problem to contact cisco support by call.
View 4 Replies
View Related
Jan 11, 2011
We have 5 wap54g and before few days I got below mention issue.
This is the issue with the MAC-address of the Linksys Access points. After resetting the APs to the Factory default mode, all the APs MACaddress has changed to one particular MAC id I.e. 00-90-4C-91-00-01.whether I was using mac security function earlier.And let me know how to raise a case in cisco small business .
View 1 Replies
View Related
Apr 3, 2012
Can I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies
View Related
Dec 26, 2011
I've had trouble connecting to my own internet and have no wireless. I'm using my neighbor's wireless and it's really slowing her's down. I've tried restarting my laptop (it usually works) and then reinstalled the device under "device manager". It's not the cord, I've checked with my neighbor's laptop and it works fine.I use a Sony Vaio VGN-NS140E with Windows Vista SP2.
------------------------------------------------------------------------
{ipconfig /all} This is while I only have an ethernet plugged in and no wifi connection.
Windows IP Configuration
Host Name . . . . . . . . . . . . : FairyHo
[code]....
View 7 Replies
View Related
Apr 30, 2011
I have a Dell XPS M1530 with Vista 32 bit. When i plug in a cable i get nothing, no error, and the comp does not recognize that a cable has been plugged in. I think that this started after my Hard drive failed and Dell replaced it but i'm not positive. No errors (? or !) in Device Manager and I can't find the Marvell 88E80XX 10/100 Ethernet Controller in device manager. I have attempted to Reinstall the drivers. The wireless is still working. I have one Light to the right of the port that is on all the time solid but no flashing with the cable in or out.
View 14 Replies
View Related
Oct 14, 2012
if I can use the encrypted port as unencrypted ethernet ports? url.. Each individual port on the Cisco Nexus 5010 switch is numbered, and groups of ports are numbered based on their function. The ports are numbered top to bottom and left to right.There are 20 to 28 ports on the Cisco Nexus 5010 switch, depending on which GEM is installed.
The 20 fixed ports form group 1 and are named 1/port_number. Ports 1 through 16 are unencrypted Ethernet ports. Of these, ports 1 through 8 are 10-Gigabit Ethernet and 1-Gigabit Ethernet-capable ports. Ports 17 through 20 are encryption-capable Ethernet ports.
View 1 Replies
View Related
Feb 17, 2013
I have been monitoring the alarm summary but have been off couple days and i see one of my controllers is down. Getting critical level security and message is port is down on the controller, condition link down. The other issue is config difference found between NCS and Contoller, I tried getting them to sync together but still getting the same message.
View 1 Replies
View Related
May 23, 2011
i want complete details about ethernet design and technologies
View 1 Replies
View Related
Dec 15, 2011
Ethernet controller driver?
View 1 Replies
View Related
Feb 28, 2013
Can't get my router to reognize my usb3.0 ssi 1359ru raid kabinett.
View 1 Replies
View Related
