Cisco Wireless :: 5760 AP Unsuccessful Join Attempt

Jun 13, 2013

I know these IOS controllers are new.  I ran in to an ap join issue so I figured I'd post the fix
 
Reason for last unsuccessful join attempt               : Failed to add database entry   on IOS

check the AP licenses.
 
WLC-5760#sh license right-to-use  Slot
 
#  License name   Type     Count   Period left
----------------------------------------------------------
1      apcount      adder         50    Lifetime
 
If you don't have a licenses you'll need to add them
 
CCNP - Wireless CWNA and CWAP       

View 3 Replies


ADVERTISEMENT

Cisco Wireless :: How To Configure 5760 WLC And 5760 HA WLC

May 22, 2013

I just cannot locate it. Customer purchasing two 5760 WLCs:
 
1     AIR-CT5760-500-K9
1     AIR-CT5760-HA-K9
 
I am looking for info on how to configure these 2 WLCs to work together.  How do you inform the production WLC that a HA WLC is available to sync with? Do WLCs have to be L-2 adjacent, or will HA operate at L-3?  How does this HA setup work? etc.

View 5 Replies View Related

Cisco Wireless :: Joining 3602i To WLC-5760

Jun 13, 2013

I am performing a new install of a WLC 5760 and 3602i APs.  I have limited experience in setting up WLCs.  I am hitting a brick wall in getting the AP to join my WLC. My primary document has been this deployment guide:url...I have also sifted through many of the relevant portions of these guides:  url...
 
I went through the setup wizard and followed the instructions in Ch. 2 to the letter (or at least I think I did).  I have DHCP options 43 and 60 configured per the 3600 series Getting Started Guide.I believe my AP discovery process is sound because I see activity when I power on the AP and perform debug capwap ap all from the WLC.  I have highlighted lines that I think are relevant.  I have attempted to find the answer on my own by searching the Internet for these phrases. [code]

View 1 Replies View Related

Cisco Wireless :: 5508 - Any Way To Integrate 5760

May 15, 2013

We are looking at possibly adding a second 5508 controller to our network and running in HA mode.  I see now that there are 5760's available that run on IOS.  Is there any way we can integrate a 5760 into our existing network instead of going with a second 5508?   I would prefer to invest in newer hardware whenever possible.

View 15 Replies View Related

Linksys Wireless Router :: E1200 Cisco Connect Update Unsuccessful

Nov 6, 2012

Ran CiscoConnect.E1200.1.4.12263.1.exe on laptop twice and returned the same "there is a problem result."  Disconnected router power for a few minutes in between.  Current version is 1.4.11200.0. My desktop is also connected by cable to my broadbandcable modem

View 2 Replies View Related

Cisco Wireless :: 3502I Access Point Unsuccessful Software Upgrade

Jan 16, 2013

I have a trouble with AIR-CAP3502I-R-K9 AP.I tried to upgrade IOS software in ap because it was connecting  and disconnecting to controller too often. I already upgraded one of two  access point and it working stable at this time, but the second one  not. [code] So, I even can't load new software. What can I do now?

View 19 Replies View Related

Linksys Wireless Router :: Laptop Can't Connect To E900 - Setup Unsuccessful

Nov 24, 2012

After running the installation CD on my laptop, it cant detect any wireless network. It givs me an error saying that Your router set up was not successful.

View 2 Replies View Related

Cisco :: ISE Compatibility With WLC 5760?

Jun 9, 2013

The ISE compatibility Matrix (June 5, 2013), does have a row for WLC 5760 in its tables.

The WLC 5760 Release Notes says it is compatible with with ISE without specfying which features. Why is the WLC 5760 missing from the ISE Compat Matrix and how can I get specific ISE feature support (ie CoA, DACL).

View 2 Replies View Related

Cisco :: Will AP1252AG-N-K9 Works With WLC 5760

Feb 4, 2013

We have 80 LAP1252AG and WLC 4404.  We plan to upgrade our WLC 4404 to WLC 5760 but not sure if our current APs will work with the new WLC 5760. 

View 1 Replies View Related

What Policy Use To Record Unsuccessful Logos To A Workstation

Nov 25, 2011

If you have problems setting up a computer as a domain controller,what would be the best approach? Four DNS Zones you can configure? What policy would you use to record unsucessful logons to a workstation?

View 4 Replies View Related

Cisco VPN :: 5510 - IPSEC Tunnel Won't Attempt Connection

Jul 31, 2012

I have a 5510 and a 5505 that I'm attempting to configure a simple VPN tunnel over. I have tried step by step configurations form CISCO ASA configs, as well as every source I can find. I have walked throught the config with IOS commands as well as Wizards. All my packets are dropped at the the inside or outside interface.
 
When I show SH ISAKMP command all I get are 0's straight down.

View 7 Replies View Related

Cisco VPN :: ASA 8.2(5) / AnyConnect Fails At First Attempt (certificate Authentication)

Jan 25, 2012

I'm trying to set up vpn with ASA 8.2(5) and Anyconnect 3.0.4235. The goal is  to force user to connect from registered machines only (winXP & win7 x32 and  x64). To do this, I used machine certificates issued by own CA. Certificate  is installed in machine store. I use double authentication (aaa & certificates). Everything works fine, AnyConnect browses cert store, ASA  validating machine certificate, then user is prompted for username/password  and finally if all is correct - connection is established.My problem is, that for new installation (new host), AnyConnect fails at first connection attempt. If I use aaa authentication only, connection is established, but if I use aaa & certificates - connection fails. The  appropriate .xml profile is predeployed at client host asa well as machine and root certificates.Important: When first try (aaa auth) succeded, others are always OK (with aaa. certificate or aaa & certificate authentication). Only the first one fails.The goal is to succesfuly establish connection with aaa & cert.
 
With DART i get:
******************************************
Type        : Error
Source      : acvpnagent 
Description : Function: CTransportWinHttp::WinHttpCallback
File: .CTransportWinHttp.cpp
Line: 2150

[code]....
 
Certificate is valid for sure, and as I mentioned before, if first use aaa only, the second try is OK. At ASA with debug crypto ca 255 can't see any certificate from client.

View 3 Replies View Related

Outgoing Connection Attempt After Online Banking

Mar 2, 2012

Something a little odd happened the other night. I had spent the afternoon updating all necessary programs where updates were available, did a GRC shieldsup test, did a clean and test of my system with AVG and MBAM. Everything looked fine.I went online that night however and as soon as I went to my online banking website, I noticed that there was an outgoing attempt logged in my firewall (ZoneAlarm). It was blocked. The IP address is 72.167.239.239:80 - which apparently fits in GoDaddy's IP range. Googled it and saw that someone else had the same issue.

View 2 Replies View Related

Monitor URL Access Attempt Website Filter?

Jan 10, 2012

i need to block internet on all computers in our clinic except few websites (URL) that we need. I'm doing this on the router in WEBSITE filter in the manner of DISABLE ALL, except...

Specifically i have issues with using FAX client. ringcentral.com is ENABLED on the router, so anything within this DOMAIN will work (as forum.ringcentral.com etc.)

BUT when i attempt to send a fax, it falls into a black hole. although the client application shows - being sent, it wont go to SENT items and it just disappears. When i disable the website filter on router, it works.

there must be a different URL that the ring central call controlled tries to connect when sending. Receiving works no problem even with the website filter on. How do i detect / intercept what ULR / IP address is truing to be reached so i can enable it on the website filter ?

View 3 Replies View Related

Cisco Switching/Routing :: SRW224G4P - IP Address To Attempt Access Via Webview

Feb 5, 2013

I have a SRW224G4P managed switch with webview, however I do not know what the IP address is of the unit to attempt to access via webview.  I've tried to connect a serial cable to the console port and use HyperTerminal to access the switch, however the switch boots up and I never see anything in hyperterminal!  I'm using the recommended port settings for the device.  What else can I do to be able to set my IP address?  Is there a hard physical reset that I can do on this unit somewhere since I can't seem to get the console mode to work?

View 0 Replies View Related

Cisco :: 1242ag Can Run At AP Prompt To Attempt To Re-flash This Unit Or Reset Password

Jan 9, 2011

I just purchased a used 1242AG which is running Version 12.4(13d)JA.I tried the mode button on power on holding for  2-3 seconds, but nothing happens and Cisco/Cisco login does not work. I have figured out if I hold the mode button in for 30 seconds while powering up I get an AP prompt.I tried doing a dir flash but get permission denied.Is their any commands I can run at AP prompt to attempt to reflash this unit or reset password somehow?

View 7 Replies View Related

Cisco Wireless :: How To Join The AP To WLC2500

May 16, 2013

I am new to Cisco wireless solution and would like to ask how to add the AP to the WLC properly. All Cisco 1041 and Cisco 2500 WLC are new. I connect those AP and WLC to the switch without any VLAN tag and the AP can gain the IP address from our DHCP correctly. However, the AP 1041 could not join the WLC successfully.

WLC: Cisco 2500
IP Address: 192.168.1.225
version: 7.4.100.0

View 5 Replies View Related

Cisco Wireless :: AIR-LAP Does Not Join With WLC2100

Mar 24, 2013

Our offcie use WLC2100 Series controller with AIR-LAP1031 and successfully join and running. Now i am trying to replace one ap with AIR-LAP1041N and join with WLC, but i can't and below  the error message generate:
 
[code]....

View 2 Replies View Related

Cisco Wireless :: LAP1131AG Won't Join WLC On SRE-ISM

Jul 10, 2012

I am trying to set up a Wireless network a WLC hosted on an SRE module in a 2911 router. I think i have most of my bases covered but there is still one problem.
 
My LAP1131AG AP's won't join the controller, on the AP im am seeing this:
Translating "CISCO-LWAPP-CONTROLLER.test.local"...domain server (192.168.250.10) [OK]

[Code].....

But to my knowledge an LWAP AP schould be able to join a CAPWAP WLC

View 2 Replies View Related

Cisco Wireless :: AP1252 Can't Join On WLC

Apr 8, 2012

WLC software 7.2.103.0
 
1. first problem: AP1252 can´t join on WLC. MAC was add on mac filter properly.
 
170Mon Apr 9 15:37:32 2012Mesh Node '2c:3f:38:be:53:ef' failed to join controller, MAC address not in MAC filter list.171Mon Apr 9 15:37:32 2012AAA Authentication Failure for UserName:2c3f38be53e0 User Type: WLAN USER172Mon Apr 9 15:37:32 2012Coverage hole pre alarm for client[1] 40:a6:d9:ef:87:68 on 802.11b/g interface of AP 2c:3f:38:bf:0c:80 (AP2c3f.38bf.0c80). Hist: 46 7 5 4 2 1 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0173Mon Apr 9 15:37:32 2012Coverage hole pre alarm for client[1] 8c:7b:9d:05:a0:67 on 802.11b/g interface of AP 2c:3f:38:bf:0c:80 (AP2c3f.38bf.0c80). Hist: 50 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0174Mon Apr 9 15:37:30

[code]....

Several APs can´t join on WLC and all are added on MAC filter, but they are showing this messages.  
 
2 . Second problem.:  Operational Status = UNKNOWN

Some Access Point are in UNKNOWN status. I tried but I can´t do the reboot. I can access Web config the APs using WLC, but when I applied the reset, it wasn´t working properly.

View 2 Replies View Related

Cisco Wireless :: 2504 - AP Cannot Join WLC

Jun 10, 2013

I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
 
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
 
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
 
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable

View 15 Replies View Related

Cisco Wireless :: AP 1131 Won't Join WLC

Jan 31, 2013

I have converted ap 1131 from autonomous to lwapp successfully by using upgrade utility tool but the AP does not join the WLC 2106. I can see it as a neighbor on the switch with no IP address.

View 19 Replies View Related

Cisco Wireless :: 4402 WLC Cannot Join More Than 47 APs

Jun 29, 2011

My WLC running 6.0.182.0 suddenly could not accept more than 47 APs! Ihave a 1240 trying to join but failed with no obvious reason (no special errors in debugging).

I unplugged one of the joined and the first one joined!! I replugged the second one but could not join!! I unplugged the first one and replugged the second one: the second joined the controller but the first could not associate again!

View 4 Replies View Related

Cisco Wireless :: 4400 - APs Not Join To WLC

Jan 24, 2011

I have a 4400 WLC for 100APs running the 7.0.98.0software version. Now, only 48 APs are joined, and the WLC dont accept new joins. The log below are from my WLC but appear for all others APs:
 
%LOG-6-Q_IND: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:3a:98:ae:e3:f0 supporting CAPWAP%LWAPP-6-CAPWAP_SUPP_VER: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:3a:98:ae:e3:f0 supporting CAPWAP%CAPWAP-3-TX_ERR: capwap_ac_sm.c:1966 Failed to transmit discovery response to AP 00:3a:98:ae:e3:f0%CAPWAP-3-ENCODE_ERR: capwap_ac_sm.c:2269 Failed to encode Discovery (code)

View 2 Replies View Related

Cisco Wireless :: AP 1262 Cannot Join WLC 4402

Jun 7, 2012

We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
 
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
 
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
  
Setup
 
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's  IP address
- Opotion 60 is also configured with  AP Manager's  IP address
- the port connected to the APs are in the AP Manager VLAN

View 12 Replies View Related

Cisco Wireless :: WLC 2504 Not Join AP1130ag?

Mar 12, 2013

I have a problem in join my ap1130ag in my wlc 2504 i activate dhcp internel (172.19.1.50 ----> 172.19.1.60) in wlc and this wlc affected address for ap1130ag (172.19.1.51) wlc and ap1130ag is connected with switch  2960 (port 17,18) this port the switche is configured in trunk mod allowed all vlan then my wlc not detected ap1130ag?

View 4 Replies View Related

Cisco Wireless :: AP 1310 Not Able To Join Controller

May 20, 2013

i converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
 
here is the output of debug command
  
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table

[Code].....

View 3 Replies View Related

Cisco Wireless :: LAP1242 Cannot Join WLC2500?

Jan 16, 2013

I have some LAP1242 which by mistake were bought for Mesh. I am trying to convert them to LWAPP so what I did first was to convert them to Stand Alone then to LWAPP but I cannot get the AP to join the WLC and sends several error logs.
 
I attached some logs taken from AP and WLC so that you can figure out what's going on.
 
I wonder if I have to remove anything from flash either on SA or LWAPP mode (I know that in some cases you have to delete privete-config in order to avoid the AP taken previous configurations). By the way I think I had never seen this c1240-k9w8-mx.124-25e.JA2 on an AP IOS before, I wonder if it has to do with the mesh thing.

View 27 Replies View Related

Cisco Wireless :: To Join 1262 With Wlc 2100

Apr 1, 2012

I have a cisco AIR-LAP1262N-A-K9  and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version 7.0.98.0)My ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?

View 1 Replies View Related

Cisco Wireless :: AP3502I-E-K9 Cannot Join WLC2504

May 23, 2013

I have WLC 2504 and AP3502I . AP can not join wireless controller .
 
*May 24 16:33:51.871: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*May 24 16:33:51.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.80.90.99 peer_port: 5246

[code].....

View 9 Replies View Related

Cisco Wireless :: AP 360021 Cannot Join WLC 5508

Mar 16, 2013

I have a cisco 5508 WLC and 40 cisco 360021 APs.I configured the WLC and assign the management interface IP and also configured a DHCP pool on my Cisco 4507 core switch wit option 43.But the problem that the APs connot join the WLC.

View 31 Replies View Related

Cisco Wireless :: LAP1142 Cannot Join WLC 2100

Apr 2, 2013

I'd WLC 2100 series and 9 access point LAP1142N .8 LAP1142N can work fine and join a capwap controller is ok but only one LAP1142  is can not . Part of LAP  is AIR-LAP1142N-A-K9
  
Apr  2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway  - gateway found
*Apr  2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway  - gateway found
*Apr  2 10:52:42.284: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC.
*Apr  2 10:52:42.284:  status of voice_diag_test from WLC is false
*Apr  2 10:52:52.284: %CAPWAP-3-ERRORLOG: Go join a capwap controller

[code]....

View 4 Replies View Related

Cisco Wireless :: AP 1262 Cannot Join WLC 4402

Jun 6, 2012

We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC.
 
The AP gets the address from dchp
 
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
 
I already read the info on the this link : [URL]
 
Still our AP cannot join the WLC no matter what i have tried.
  
Setup
 
- VLAN setup on a Cisco 3560 48 port poe Switch

- tunk configured btwn the Gi Interface and the Management physical port

- WLC mode is configured for Layer 3

- AP Manager and Management are in the same Subnet

- Option 43 is configured for the with the AP Manager's  IP address

- Opotion 60 is also configured with  AP Manager's  IP address

- the port connected to the APs are in the AP Manager VLAN

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved