Monitor URL Access Attempt Website Filter?
Jan 10, 2012
i need to block internet on all computers in our clinic except few websites (URL) that we need. I'm doing this on the router in WEBSITE filter in the manner of DISABLE ALL, except...
Specifically i have issues with using FAX client. ringcentral.com is ENABLED on the router, so anything within this DOMAIN will work (as forum.ringcentral.com etc.)
BUT when i attempt to send a fax, it falls into a black hole. although the client application shows - being sent, it wont go to SENT items and it just disappears. When i disable the website filter on router, it works.
there must be a different URL that the ring central call controlled tries to connect when sending. Receiving works no problem even with the website filter on. How do i detect / intercept what ULR / IP address is truing to be reached so i can enable it on the website filter ?
View 3 Replies
ADVERTISEMENT
May 2, 2011
I have several laptops at home that connect via wireless connection tot he DIR_655. Using the MAC address of those laptops, I want to prevent them from going to certain websites.Under 'Advanced" and "Website Filter", I addes several domain names (websudoku.com for example). I selected "DENY computersaccess to ONLY these sites". I then saved settings.I then went to "Access Control". I clicked on "Enable Access Control".I clicked on "Add Policy" to cdreate a new policy for one of the laptops.When I boot the laptop and go to one of the websites, it still allows me access. The URL/domain name is correct.
View 5 Replies
View Related
May 4, 2011
I'm trying to set up a website filter on my DIR-601. I created a policy for 2 MAC addresses, with a schedule from 10AM-6PM, selected "Block some websites", and disabled logging. Under website filter, I added some entries, and selected "DENY computers access to ONLY these sites". When the policy is enabled, and I try to access one of the blocked websites, it gets blocked correctly ("The URL access was denied by administrator.") However, for all other websites, I get "server unexpectedly dropped the connection" errors, eg "Safari can�t open the page [URL] because the server unexpectedly dropped the connection. This sometimes occurs when the server is busy. Wait for a few minutes, and then try again." or in Chrome "No data received. Unable to load the webpage because the server sent no data." This happens with ALL non-blocked websites. I'm using hardware version A1, firmware version 1.01NA.
View 2 Replies
View Related
Jan 12, 2012
I had the website filter ON and it was working very well to block a few websites on a schedule. And after a few month, it doesn't work any more. While it is possible that I scewed up the setting , I have tried so many settings.
So:DIR655 fw 1.32NA,hw A3,"Enable access control" is on with the desktop MAC address (used copy this MAC)(I have also tried my laptop MAC),web site filter is set to "deny",the router time is set using NTP dlink server,
View 3 Replies
View Related
Feb 5, 2013
I have a SRW224G4P managed switch with webview, however I do not know what the IP address is of the unit to attempt to access via webview. I've tried to connect a serial cable to the console port and use HyperTerminal to access the switch, however the switch boots up and I never see anything in hyperterminal! I'm using the recommended port settings for the device. What else can I do to be able to set my IP address? Is there a hard physical reset that I can do on this unit somewhere since I can't seem to get the console mode to work?
View 0 Replies
View Related
Mar 2, 2012
Something a little odd happened the other night. I had spent the afternoon updating all necessary programs where updates were available, did a GRC shieldsup test, did a clean and test of my system with AVG and MBAM. Everything looked fine.I went online that night however and as soon as I went to my online banking website, I noticed that there was an outgoing attempt logged in my firewall (ZoneAlarm). It was blocked. The IP address is 72.167.239.239:80 - which apparently fits in GoDaddy's IP range. Googled it and saw that someone else had the same issue.
View 2 Replies
View Related
Jul 31, 2012
I have a 5510 and a 5505 that I'm attempting to configure a simple VPN tunnel over. I have tried step by step configurations form CISCO ASA configs, as well as every source I can find. I have walked throught the config with IOS commands as well as Wizards. All my packets are dropped at the the inside or outside interface.
When I show SH ISAKMP command all I get are 0's straight down.
View 7 Replies
View Related
Jun 13, 2013
I know these IOS controllers are new. I ran in to an ap join issue so I figured I'd post the fix
Reason for last unsuccessful join attempt : Failed to add database entry on IOS
check the AP licenses.
WLC-5760#sh license right-to-use Slot
# License name Type Count Period left
----------------------------------------------------------
1 apcount adder 50 Lifetime
If you don't have a licenses you'll need to add them
CCNP - Wireless CWNA and CWAP
View 3 Replies
View Related
Jan 25, 2012
I'm trying to set up vpn with ASA 8.2(5) and Anyconnect 3.0.4235. The goal is to force user to connect from registered machines only (winXP & win7 x32 and x64). To do this, I used machine certificates issued by own CA. Certificate is installed in machine store. I use double authentication (aaa & certificates). Everything works fine, AnyConnect browses cert store, ASA validating machine certificate, then user is prompted for username/password and finally if all is correct - connection is established.My problem is, that for new installation (new host), AnyConnect fails at first connection attempt. If I use aaa authentication only, connection is established, but if I use aaa & certificates - connection fails. The appropriate .xml profile is predeployed at client host asa well as machine and root certificates.Important: When first try (aaa auth) succeded, others are always OK (with aaa. certificate or aaa & certificate authentication). Only the first one fails.The goal is to succesfuly establish connection with aaa & cert.
With DART i get:
******************************************
Type : Error
Source : acvpnagent
Description : Function: CTransportWinHttp::WinHttpCallback
File: .CTransportWinHttp.cpp
Line: 2150
[code]....
Certificate is valid for sure, and as I mentioned before, if first use aaa only, the second try is OK. At ASA with debug crypto ca 255 can't see any certificate from client.
View 3 Replies
View Related
Mar 20, 2012
Is it possible to filter remote access VPN traffic on a PIX 501 (like you can on an ASA?)
View 1 Replies
View Related
Jan 9, 2011
I just purchased a used 1242AG which is running Version 12.4(13d)JA.I tried the mode button on power on holding for 2-3 seconds, but nothing happens and Cisco/Cisco login does not work. I have figured out if I hold the mode button in for 30 seconds while powering up I get an AP prompt.I tried doing a dir flash but get permission denied.Is their any commands I can run at AP prompt to attempt to reflash this unit or reset password somehow?
View 7 Replies
View Related
Apr 6, 2011
I tried to configure my wifi router recently to secure my internet connection. I wanted to add a MAC adress filter, but I had to leave before I could enter them all. I thought that I wouldn't have to enter my own MAC adress since I'm directly connected to the router with a wire, but it looks like I should have entered my MAC adress, because now I can't get access to my router by typing the IP adress, as usual. I tried to reset it, but it doesn't work.
View 2 Replies
View Related
Mar 10, 2011
I'm trying to find the maximum number of mac filters that are supported on the Cisco 4410N access point. The datasheet says that it supports mac filtering but does not indicate the maximum number of filters.
View 3 Replies
View Related
Aug 21, 2011
If you have MAC filter enabled with the E4200 Firmware Version: 1.0.01 you cannot connect to guest.
View 2 Replies
View Related
Sep 3, 2012
I have a router 2811 that it's configured with VPN remote access and I'm trying to block clients based on their MAC address, I tried configuring access interface as routing/bridging, configured an ACL 750 for 48-bit MAC address access list and enable "bridge-group 1 input-address-list 750" command on bridged interface, but the only match I got when VPN clients access the LAN is from router interface.
Internet(VPN) ---> Router1 (FE 0/1) ---> Router1 (FE 0/0) --> Router2 (FE 0/0) --> Router2 (FE 0/1) --> LAN
I tried configuring on Router1 (FE 0/0) interface and also on Router2 (FE 0/0) interface with same behaviour. Router2 is used for internal NAT.
bridge irb
bridge 1 protocol ieee
bridge 1 route ip
[Code].....
View 4 Replies
View Related
Aug 20, 2012
We have a Cisco ASA 5520 and Web sense. I added a filter but it seems like it is still not allowing us to access a certain website from most of the machines however some machines with the same configuration work on the DMZ. Accessing website tells us:
"Firefox has detected that the server is redirecting the request for this address in a way that will never complete".
Filter I applied on the firewall:
filter url except 0.0.0.0 0.0.0.0 64.18.218.0 255.255.255.0 allow
filter https except 0.0.0.0 0.0.0.0 64.18.218.0 255.255.255.0 allow
View 9 Replies
View Related
Aug 28, 2011
For some reason I can't get Access Control/Webaccess Filters working on my Dir-655 w/ 1.35NA. I've tried it with MAC and IP Address without any success. I've also enabled/disabled/enabled DNS Relay, recreated the rules, recreated the filters, etc. Nothing.
View 14 Replies
View Related
Oct 16, 2011
I'm using my 655 as a WAP, so nothing is connected to the WAN port. Since I run a SBS2008 in my home, I also have the 655's DHCP disabled.If I enable Network Filtering, everything inbound/outbound on the LAN ports works except accessing the Admin page. Even if I put the connecting PC's LAN MAC in the tablet.
View 9 Replies
View Related
Mar 5, 2012
I would like to monitor access ports to servers in cases:
- When port to server down, alert appears in Fault Monitor panel
- Monitor when bandwidth utilization of access ports exceeds 60%.
I configured Fault Threshold on DFM>System Defined Groups>Access port Settings and Poller settings on the same group but it did not work when I shut a port to server.
View 2 Replies
View Related
Jan 21, 2012
for sometime I have not been able to access any google website. I can access all others?
View 5 Replies
View Related
Feb 20, 2013
So recently i decided to try to play some rune scape since i played it through my childhood and wanted to try again, it went fine first 2 days, and after that i can't access the website at all. I've tried to ping it, and all that comes up is that request timed out, tried flush dns, restarting router/modem and even to change ip (which i did not succeed with).However i found this "solution" url... and reading the top comment, it says that "This problem occurs when viewing the same site over a router from more that one computer or application at the same time for a period of time." And i have done exactly that in the past days the site was working.
View 5 Replies
View Related
Apr 24, 2012
I'm trying to reach [URL] and just keep getting a timed out message. I had this problem before once and gave up trying to solve it and then one day I came across a post at SWI in my google results and amazingly, I was able to access the site. I have no idea what was different on that particular day.
Same symptoms in Firefox and IE so I don't think its a browser issue.
Tried accessing the site through the IP address - same result.
Tried safe mode with networking - same result
I reset my router a few days ago because of another issue but I haven't reset it since this problem began. I have tried restting my router dns to opendns and also google public dns, neither of which has made any difference.
I got a friend to confirm that the site is not down, as I suspected. Tried to ping the site using this and the only 2 UK locations on the list said 100% packet loss - is this relevant?
View 14 Replies
View Related
Mar 17, 2012
I'm having problem accessing myanimelist.net for months. I can access other websites except it. Some days I can access it and some days I cant. Just this morning I accessed it and then I returned during the afternoon and I can't access it anymore.
I tried doing the tracert in command prompt
C:Userswin7>tracert myanimelist.net
Tracing route to myanimelist.net [72.172.76.139]
over a maximum of 30 hops:
[Code].....
View 16 Replies
View Related
Dec 9, 2012
For the last couple months, I have had a serious problem with connecting to one (and only one) website: cms.bsu.edu (Ball State University, 147.226.7.60). This occurs from my home using a broadband connection. I say serious because this is my work website and I am an online instructor. Not being able to access BSU creates a serious problem for me. Note that this is 1) only an intermittent problem (only happens every few weeks, lasts for a day to a couple days, typically), 2) occurs with any and all browsers that I have tried, 3) occurs cross-platform (Mac or Win), on multiple machines, 4) goes away when using a neighbor's wi-fi signal from my home, 5) goes away when using these same machines with any other IP address (at McDonald's, BSU, etc., etc., etc.)Tech support at my IP suggested that we download virus software and confirm that the system is not infected.
We did this, but let me call your attention to the fact that 1) this is occurring to ALL of our computers simultaneously -- even though they are running different operating systems and that 2) there are virtually no viruses that infect more than one OS. So, the likelihood that this is a virus is very, very, very small. Furthermore this is intermittent (not typical of viruses), and two goes away when using anything other than our Ninestar ISP IP. Hopefully, you are beginning to see a trend here.Ninestar tech support has also suggested that the problem might be with our wi-fi router. However, that is not the case, as this problem exists even when hard-wired directly through the Ethernet (no wi-fi).
As far as I can tell, that pretty much isolates this problem to two sources:ttp//:cms.bsu.edu (Ball State University) and my ISP (NineStar). We have contacted Ball State and they have had no other reports of this problem. Since they have thousands of connections made per hour from the same platforms (PC and Mac) running the same software, that makes it very unlikely that the problem lies with them. Today, with BSU still unaccessible, I decided that I should force a reboot on the entire Ethernet system at home.
There is a box in my garage that is designed to route the signal to my phones, my cable, and my internet router so I powered it down just in case. This didn't make a bit of difference. Ethernet still works fine for all sites except 147.226.7.60. I also pinged BSU. Timed out on both Mac and PC via direct Ethernet connectionFinally, I have used proxies to visit BSU, but since they don't handle encrypted signals, this doesn't really . No email, no Blackboard, pretty much only viewing their website is possible.
View -1 Replies
View Related
Aug 21, 2012
I've been trying to access a particular website for several days now, but every time I try to I get the "Oops! Google Chrome could not connect to" error.The website in question is:I know that it is working as other people who I know post on the forum have not had the same problem.I've tried the standard things of clearing cache, switching wireless router off/on but still nothing.
View 15 Replies
View Related
Jul 10, 2012
I can't seem to be able to access my personal website from any of my home devices: computer,2xlatop,android phone all give me the same message: "Cannot connect to thebianchifam.mercury-gaming.com" I've been trying to connect with Google Chrome, IE and Firefox yet none of them work on either of the devices. I've asked other people to connect to the website and everyone says it's working just fine. I even used teamviewer on another computer in America and saw myself that it was working just fine. Also using the website : url... lets me connect just fine to website but It's rather annoying having to use a proxy server to do all the intensive forum work. I've been reading around all the forums and have found people with the same problem but none of them actually posted back saying how they fixed it. I was literally editing a blog page when I clicked on update and the website didn't let me connect anymore. I've tried flushing the DNS through CMD line with the "ipconfig /flushdns" command but it has yet to do anything. I restarted the rooter in the hope it will work but no succees. url...
View 14 Replies
View Related
Sep 22, 2012
I've gone through a variety of diagnostics and I honestly don't know what to think. It's not my computer, as I can access the site on this computer on a different network. It's likely not the whole of my LAN network either, because my kindle can access the site through it. I can always access it on this computer with a proxy as well. I can ping it fine, and tracert it equally as well.I've tried everything from socket fixes, DNS flushes, getting new WAN IP addresses. When I got a new WAN IP address the first time the site was accessible once, and then it stopped again after that. I can't clone the MAC address from the router, because it doesn't allow it.
View 7 Replies
View Related
Feb 21, 2011
It's a safe site that I have used before and that others can still access. The last time I was able to access it was around New Years. I have tried quite a few times since without any luck. (I had hoped the problem would simply "go away"....).
[code]....
View 2 Replies
View Related
Feb 14, 2011
For some reason, there is a specific website that I cannot access. I am a member of the website and they have a community forum for contacting them and requesting support, but obviously I cannot contact them if I cannot access their site!
The website is [URL]. I read in another post that I should do the TRACERT command and post the results so I am doing that here.
View 4 Replies
View Related
May 11, 2011
My internet provider have blocked a website. I know there is a way to bypass the block and go to the website, without using websites such as Hide My ***! Free Proxy and Privacy Tools - Surf The Web Anonymously.
View 1 Replies
View Related
May 26, 2012
Ever since last night ive not been able to get onto a site that i use every single day. I can get on the site through my 3g on my phone and ive tried it round my friends house and it works perfectly.Tried releasing and renewing my IP Address, no effect and have just ran a Tracert:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersMatty>tracert olbg.com
Tracing route to olbg.com [164.177.153.185]
[code]...
View 1 Replies
View Related
Feb 16, 2012
I can get on any website except google.com if its anything else such as images.google.com or gmail it works fine but I cannot get on the main google page. Can't ping it either.
View 1 Replies
View Related
Jan 17, 2013
We have been noticing a strange issue since upgrading to Comcast Business with a new Motorola 6580 modem/router:certain common websites can no longer be accessed via the network (although they load fine when accessed via smartphone 3/4G)I already did some reading on the subject and it looks like the Firewall is to blame:when I switch Firewall to "Off", everyone can access the websites ok,as soon as I switch Firewall back to "Low" - no more website access.Question: is there any workaround for this issue other than turning off the Firewall?
View 1 Replies
View Related
