Cisco Switching/Routing :: SRW224G4P - IP Address To Attempt Access Via Webview
Feb 5, 2013
I have a SRW224G4P managed switch with webview, however I do not know what the IP address is of the unit to attempt to access via webview. I've tried to connect a serial cable to the console port and use HyperTerminal to access the switch, however the switch boots up and I never see anything in hyperterminal! I'm using the recommended port settings for the device. What else can I do to be able to set my IP address? Is there a hard physical reset that I can do on this unit somewhere since I can't seem to get the console mode to work?
View 0 Replies
ADVERTISEMENT
Jun 8, 2011
The switch functions and operates fine but I can no longer login to the webview(GUI) and when I use a serial cable to console in to it, it shows nothing on the hyperterminal meaning no login. How can I get back into the switch to manage it or reset it back to factory settings? I kept the default IP address and I enabled HTTPS to login by gui, well I got in by HTTPS so I went in to turn that setting off and hit apply and now I can't log into it at all.
View 1 Replies
View Related
Apr 11, 2010
We have about 30 SRW224G4P switches throughout our network(each one located at remote site) and we have been having problems with these locking up. Normal symptoms are; I can ping the switch but cannot get to the login promot via telnet, ssh, or web-gui even though the ports are open. And how to plugged into the switch after this happens canont reach my router for DHCP.
I did a firmware upgrade to "SRW224G4P_SRW248G4P_image.bix" on one of the switches at our office and this seemed to fix the problems however after the upgrade was compete the config was blank. Is that suppose to happen or did I miss something? I would like to upgrade the firmware on all my our SRW224G4P switches without having to travel to each remote location and reconfigure each switch after the upgrade.
View 6 Replies
View Related
May 4, 2012
Are there any manuals on how to open the srw224g4p switch? I can't find anything the switch is making a lot of noise - sound like the fan.
View 2 Replies
View Related
Jan 10, 2012
i need to block internet on all computers in our clinic except few websites (URL) that we need. I'm doing this on the router in WEBSITE filter in the manner of DISABLE ALL, except...
Specifically i have issues with using FAX client. ringcentral.com is ENABLED on the router, so anything within this DOMAIN will work (as forum.ringcentral.com etc.)
BUT when i attempt to send a fax, it falls into a black hole. although the client application shows - being sent, it wont go to SENT items and it just disappears. When i disable the website filter on router, it works.
there must be a different URL that the ring central call controlled tries to connect when sending. Receiving works no problem even with the website filter on. How do i detect / intercept what ULR / IP address is truing to be reached so i can enable it on the website filter ?
View 3 Replies
View Related
Sep 15, 2012
I have a 2921, and I have 4 network segments. In segment 172.16.0.0./27 I wand to "pair" somehow connections. I mean IP 172.16.0.x has to have MAC aaaa.bbbb.cccc and so on, and not accept connections otherwise.How can I do that?
View 7 Replies
View Related
Jan 22, 2012
I have a 1841 deployed as my NAT device towards internet. NAT is setup so that internal addresses can access WWW. I also have some NAT translations opening speciic ports from outside to inside in the form: ip nat inside source static tcp A.B.C.D 443 A.B.C.D 443 extendable.
Now have an outside address/port setup with a public DNS reference and using NAT from outside to get access to the corresponding inside address. It works when being outside the LAN.
Now to the problem: From the LAN side of the router - i cannot access the public name. I can ping it - but my browser dont find the webserver behind the name. Someone told me it should be setup as "local firewall domain" - and i should set this up as "source NAT".
View 12 Replies
View Related
Oct 16, 2012
Today when we run one applcation to access a target server with IP address 10.2.2.13, the application cannot run through and appearing error message related networking.The target server has two network ports whereby another one with IP 10.2.2.14 is running OK with the same application. All these two connections are connected to the same Cisco switch 3750, after the switch then go to Cisco ASA firewall which has no access control rule for this 10.2.2.13 and its subnet, and then the firewall connect directly to the application server.We can ping, remote desktop access and telent port for the application to the target server by using 10.2.2.13.We swapped the cable connection of the ports from one another and try the application again, the IP with 10.2.2.13 is still fail and IP with 10.2.2.14 is OK.We then change the IP from 10.2.2.13 to 10.2.2.12 or 10.2.2.155, all are OK. We changed back to 10.2.2.13, it is failed again.The switch is in running real time production and so we cannot power cycle or reload the switch.
View 9 Replies
View Related
Dec 11, 2012
I just ran into an interesting issue. VG Cisco 3825 crashes regularly with the following message in a crashinfo.
%ALIGN-1-FATAL: Illegal access to a low address 16:26:07 CET Tue Dec 11 2012
addr=0x0, pc=0x603EFF38z , ra=0xFFFFCC41z , sp=0x702E3C28
%ALIGN-1-FATAL: Illegal access to a low address 16:26:08 CET Tue Dec 11 2012
addr=0x0, pc=0x603EFF38z , ra=0xFFFFCC41z , sp=0x702E3C28
16:26:08 CET Tue Dec 11 2012: TLB (store) exception, CPU signal 10, PC = 0x603F32F8
Router: Cisco 3825
IOS: c3825-spservicesk9-mz.151-3.T3.bin
View 1 Replies
View Related
Sep 4, 2012
I am using cisco 1841 LAN router, I need to block MAC address i have applied the command access-list 1102 deny 0000.0000.0000.0000 mac address..... but it does not work.
View 24 Replies
View Related
Oct 6, 2011
I am unable to connect to webview on our SRW2024 switch. I use a macpro G5 running 10.6.8. When i try to connect to it through Safari, Chrome, or Firefox using 192.168.1.254, I receive a message that a connection cannot be established. 192.168.1.254 is the ip mentioned in the manual. I used an ip scanner and it showed the actual ip is 192.168.0.1. But I cannot connect to webview through this ip either. We got this switch a year ago and did not change any settings, we just connected it and it worked fine. But now we want to change some settings on the switch but cannot connect.
View 1 Replies
View Related
Jul 19, 2012
On my SG300 I set up LAG for the last two ports.
I then plugged them into my SRW224G4P, once I do that I get dropped packets.
I was thinking maybe doing firmware upgrades to both switches?
View 3 Replies
View Related
Jun 7, 2011
I have a question on 300 series PoE switch (SRW224G4P, power budget: 180W). How many WAP 4410N can be powered by this switch??How many AP 1242 can be powered by this switch? Since CDP is not supported yet, I think switch will provide 15.4W power for each AP. So each switch can power up to 11 WAP4410N or AP 1242. Is this correct??
One other quesiton is When CDP is supported, can I calculate as below? WAP4410N (Power draw:10.1W): 180/10.1W = 17.xx -> Up to 17 WAP4410N can be powerd AP1242 (Power draw:12.4W): 180/12.4W = 14.xx -> Up to 14 WAP4410N can be powerd
View 1 Replies
View Related
Jul 31, 2012
I have a 5510 and a 5505 that I'm attempting to configure a simple VPN tunnel over. I have tried step by step configurations form CISCO ASA configs, as well as every source I can find. I have walked throught the config with IOS commands as well as Wizards. All my packets are dropped at the the inside or outside interface.
When I show SH ISAKMP command all I get are 0's straight down.
View 7 Replies
View Related
Jun 13, 2013
I know these IOS controllers are new. I ran in to an ap join issue so I figured I'd post the fix
Reason for last unsuccessful join attempt : Failed to add database entry on IOS
check the AP licenses.
WLC-5760#sh license right-to-use Slot
# License name Type Count Period left
----------------------------------------------------------
1 apcount adder 50 Lifetime
If you don't have a licenses you'll need to add them
CCNP - Wireless CWNA and CWAP
View 3 Replies
View Related
Jan 25, 2012
I'm trying to set up vpn with ASA 8.2(5) and Anyconnect 3.0.4235. The goal is to force user to connect from registered machines only (winXP & win7 x32 and x64). To do this, I used machine certificates issued by own CA. Certificate is installed in machine store. I use double authentication (aaa & certificates). Everything works fine, AnyConnect browses cert store, ASA validating machine certificate, then user is prompted for username/password and finally if all is correct - connection is established.My problem is, that for new installation (new host), AnyConnect fails at first connection attempt. If I use aaa authentication only, connection is established, but if I use aaa & certificates - connection fails. The appropriate .xml profile is predeployed at client host asa well as machine and root certificates.Important: When first try (aaa auth) succeded, others are always OK (with aaa. certificate or aaa & certificate authentication). Only the first one fails.The goal is to succesfuly establish connection with aaa & cert.
With DART i get:
******************************************
Type : Error
Source : acvpnagent
Description : Function: CTransportWinHttp::WinHttpCallback
File: .CTransportWinHttp.cpp
Line: 2150
[code]....
Certificate is valid for sure, and as I mentioned before, if first use aaa only, the second try is OK. At ASA with debug crypto ca 255 can't see any certificate from client.
View 3 Replies
View Related
Mar 2, 2012
Something a little odd happened the other night. I had spent the afternoon updating all necessary programs where updates were available, did a GRC shieldsup test, did a clean and test of my system with AVG and MBAM. Everything looked fine.I went online that night however and as soon as I went to my online banking website, I noticed that there was an outgoing attempt logged in my firewall (ZoneAlarm). It was blocked. The IP address is 72.167.239.239:80 - which apparently fits in GoDaddy's IP range. Googled it and saw that someone else had the same issue.
View 2 Replies
View Related
Jan 9, 2011
I just purchased a used 1242AG which is running Version 12.4(13d)JA.I tried the mode button on power on holding for 2-3 seconds, but nothing happens and Cisco/Cisco login does not work. I have figured out if I hold the mode button in for 30 seconds while powering up I get an AP prompt.I tried doing a dir flash but get permission denied.Is their any commands I can run at AP prompt to attempt to reflash this unit or reset password somehow?
View 7 Replies
View Related
Dec 28, 2011
This is my first time trying to configure a WAP for out network. I have an AP1141 connecting to an SG300-28 switch. The subnet for my WAPs is 10.10. 40.0/ 24. The rest of my internal network is 10.10.10.0/24. There are four other WAPs on the 10.10.40.0/24 network that I did not configure. When I assign an IP address - 10.10.40.7 to my WAP with the gateway as 10.10.40.100 (router), I cannot ping anything. If I assign the WAP an IP address - 10.10.10.192 with the gateway 10.10.10.100 (router), I can ping everything.
View 6 Replies
View Related
Aug 10, 2011
I disconnected and reconnected the powercable while holding on to the setup button until system, alert, setup go amber. The system led light began blinking green. I waited until one of the leds lights on the ports starts blinking green I then connected the ethernet cable connected to my pc. I made sure my lan connection on my computer was set to dhcp.In the docs claim it should take about 1 minute to grab a new ip address. After a few minutes i check the ipconfig on my pc and I get the apipa address.The setup light on the switch remains green while system is amber. The led for port 1 stopped blinking and remains green.My pc is not grabbing an ip address I don't know what else to do.
View 7 Replies
View Related
Nov 18, 2012
We have a Router with one External IP and a couple of VLANs. We have got a Teleconferencing Unit that needs almost every port known to man to work, so decided to get the unit its own External IP.
We have the IP now and how to get it in the router and then also to use it only for the Video unit (From outside straight through to Video).
Im comfortable adding lines to the router but just don't know what the lines should be.
The new IP's purchased are 116.199.222.200/30 (Only need to use one address, lets say 116.199.222.200). No idea what the subnet mask should be...
The router config below stripped of irrelevant stuff:
interface FastEthernet0
no ip address
!
interface FastEthernet1
[Code]......
View 11 Replies
View Related
Jan 22, 2013
I would like to know why Cat3550 SVI's mac address is always same.for example if I configure interface vlan1 and vlan2.mac address is same as like 000d.bdfc.xxxx but Cat3750 is different, each SVI has unique mac address.
View 1 Replies
View Related
Aug 26, 2007
how to configure an IPaddress for a PWR-RPS 2300?.I tried finding info on the website but no luck as yet. RPS 2300 will be used on stack of 3750E series switches.
View 3 Replies
View Related
Jan 22, 2012
I'm fairly new to Cisco configuration and I am looking at a problem for a client that involves the use of a Cisco 887 (wired only) as the main router/gateway. The problem I am investigating involves the allocatoni of DHCP addresses from the device to a product we have designed that connects to the router. I am attempting to set the 880 up on the bench with no ADSL connection and just use the DHCP feature of the box for the 4 switch ports on the back. I have tried all kinds of configurations from default. Whatever I do I can't get the router to assign an IP address to anything that is plugged in (Windows or Linux machines). What could I be doing wrong ? It can't be that difficult to get the system to just act as a DHCP server.
View 2 Replies
View Related
Apr 27, 2012
I have a POE switch running 12.0(5). I have port 24 connected as a trunk connected to the main switch. I need to add an ip address on vlan 21 which is where the network vlan is. I created it but I can not seem to enable it. I have issued the no shut command several times, but doing "sh ip int brief" it keeps showing up as administively down.
View 13 Replies
View Related
Feb 20, 2013
I would like to enable port security to hardcode the MAC address on the ethernet switch. There are 5 ethernet ports in the same ethernet switch to be assigned for one person (one note book), e.g. port 5, 6, 15, 16 and 23. The model of ethernet switch is cisco 2960S and one MAC address is configured on 2960S.
1. Does 2960S support this requirement to allow input the same MAC address to 5 different port?
2. If yes, can ethernet switch "smart" enough to forward the packages to "active" ethernet port which is connected to notebook and the rest of four ports are inactive.
3. if no, any solution or any work around to achieve this requirement
View 5 Replies
View Related
Oct 31, 2012
The customer has 4 6500 switches. 2 Physical locations, and 2 switches at each locations. The locations are connected via 1 200mpbs metro ethernet(layer 2). We ran into an issue during a DR exercise. We had created a VLAN for DR testing purposes, that did not have any SVI configured, but the VLAN did exist on one of the 6500s. When the customer restored a VM to the DR VLAN, we lost connectivity to the production server. After some troubleshooting, we found the cause to be the same mac address showing up, but in a different vlan. Once we removed the DR vlan from the 6500 all was well. It seems like switches are ignoring the VLAN in the mac address table, and forwarding to the incorrect ports. The switch is not reporting any mac flapping in the logs. No spanning tree topology changes are occurring. Code version is 12.2(33)SXJ2 on all switches.
View 1 Replies
View Related
Jan 1, 2013
I have a new 881 router and am simply trying to change the ip address from the default 10.10.10.1 to 192.168.15.1
I tried doing this both in the CCP Express app loaded on the router, and also using the desktop CCP client. I can change other parameters without any problems, but when I change the ip address of the vlan the program hangs (as expected since the ip address should be changing). I then try to open it back up and reconnect but get no response from the router.
I can ping it no problem, and the http server is running according to the serial terminal.
View 1 Replies
View Related
Jan 11, 2012
Cisco 1812, Version 12.3(8)YI1..What does "none" mean ?Most of mac adressess in cam has specified interface, but several has none.
View 12 Replies
View Related
May 20, 2013
This is probably a dumb question, but I have read the 2960 stack administration guide and it does not explain how to configure the stack IP address. It says several times that the stack can be managed from the stack IP address, and that the stack IP address is a system-level configuration item. But it never explains how to configure the stack IP address.
View 3 Replies
View Related
Apr 24, 2012
In mucking around with my 4500 I accidently deleted the ip address that I use to get into it with telnet and CNA. I have a console cable hooked up to and I'm in that way but the commands I got off the internet did not work. Those commands were set interface sc0 10.x.x.x/xx and set interface me1 10.x.x.x/xx. It didn't like interface and I notices when I did a set ?
View 6 Replies
View Related
Jan 25, 2012
I need to create several VLans on my switch.After reading the admin guide pdf, i still don't understand how to create any simple VLan.some tutorial or steps (with IE or Mozilla browser) how to create and use VLan, and to connect one VLan to another.For example,i need to create 3 VLans.
First Vlan consist of 5 ports (Vlan Name = Red)
Second Vlan consist of 15 ports (Vlan Name = Green)
Last Vlan consist of the rest of the ports (VLan Name = White)
View 7 Replies
View Related
Apr 19, 2012
I have a cisco 878 router and I can’t assign ip address to it’s fast Ethernet interface. When I assign ip address give me this message: “you can not assign ip address to layer 2 interface”.
But I can not understand why give me this alert when I use a layer3 device?!
View 3 Replies
View Related