Cisco Switches :: SRW224G4P WebView And POE / Can't Login To Gui Or Console
Jun 8, 2011
The switch functions and operates fine but I can no longer login to the webview(GUI) and when I use a serial cable to console in to it, it shows nothing on the hyperterminal meaning no login. How can I get back into the switch to manage it or reset it back to factory settings? I kept the default IP address and I enabled HTTPS to login by gui, well I got in by HTTPS so I went in to turn that setting off and hit apply and now I can't log into it at all.
View 1 Replies
ADVERTISEMENT
Feb 5, 2013
I have a SRW224G4P managed switch with webview, however I do not know what the IP address is of the unit to attempt to access via webview. I've tried to connect a serial cable to the console port and use HyperTerminal to access the switch, however the switch boots up and I never see anything in hyperterminal! I'm using the recommended port settings for the device. What else can I do to be able to set my IP address? Is there a hard physical reset that I can do on this unit somewhere since I can't seem to get the console mode to work?
View 0 Replies
View Related
Oct 6, 2011
I am unable to connect to webview on our SRW2024 switch. I use a macpro G5 running 10.6.8. When i try to connect to it through Safari, Chrome, or Firefox using 192.168.1.254, I receive a message that a connection cannot be established. 192.168.1.254 is the ip mentioned in the manual. I used an ip scanner and it showed the actual ip is 192.168.0.1. But I cannot connect to webview through this ip either. We got this switch a year ago and did not change any settings, we just connected it and it worked fine. But now we want to change some settings on the switch but cannot connect.
View 1 Replies
View Related
Jul 19, 2012
On my SG300 I set up LAG for the last two ports.
I then plugged them into my SRW224G4P, once I do that I get dropped packets.
I was thinking maybe doing firmware upgrades to both switches?
View 3 Replies
View Related
Jun 7, 2011
I have a question on 300 series PoE switch (SRW224G4P, power budget: 180W). How many WAP 4410N can be powered by this switch??How many AP 1242 can be powered by this switch? Since CDP is not supported yet, I think switch will provide 15.4W power for each AP. So each switch can power up to 11 WAP4410N or AP 1242. Is this correct??
One other quesiton is When CDP is supported, can I calculate as below? WAP4410N (Power draw:10.1W): 180/10.1W = 17.xx -> Up to 17 WAP4410N can be powerd AP1242 (Power draw:12.4W): 180/12.4W = 14.xx -> Up to 14 WAP4410N can be powerd
View 1 Replies
View Related
Mar 12, 2013
I wanted to update the F/w on my rev b dir 825, but unable to load the login console for admin, I haven't changed anything and the router was still on 2.07NA f/w
View 1 Replies
View Related
Feb 21, 2013
I have Cisco5510 running with ADSM 6.0 version, I was able to access it fine since few months but suddenly I am unable to login through that.Its prompting for username and password and loading it to 100% but not opening the GUI console.I feel this could be the JAVA version issue but with the same version of JAVA I am able run another ASA 5520 which is running with 6.4ASDM version.Request you to suggest the right JAVA version to run 5510 with ASDM 6.0 GUI console.
View 1 Replies
View Related
Aug 22, 2011
I have a console access to a Cisco 4500 series router over Cisco access server, which has following "line con 0" configuration:
View 8 Replies
View Related
Oct 23, 2012
I have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
View 4 Replies
View Related
Mar 12, 2012
I have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
line con 0
exec-timeout 15 0
logging synchronous
[Code].....
View 5 Replies
View Related
Jul 9, 2012
We are having a problem with our ACS and switch configuration.Basically if the switches lose connectivity to the ACS server the switches completely lock up, you can’t even console onto the switches.We want them to use the fall back username and password when this happens.
View 1 Replies
View Related
Nov 29, 2011
On a SF300-08, how to work with CLI and not with the Console Menu Interface ?
View 4 Replies
View Related
Apr 9, 2013
I can access the web console, and also have telnet access but only to a VT100 menu system - How do I access the full console command prompt (without using the serial console connection)?
View 4 Replies
View Related
Jan 4, 2013
I can not access the switch through the console. The web interface is working properly.
Model: SRW224g4
Below some pictures. The Hyper Terminal settings. Error:
View 6 Replies
View Related
Jan 10, 2012
My company just bought a SF300-24P, got it configured without much issue. Today I try to get into it and I can't. Tried via HTTP and console and nothing happens. Decided to try to reset it using the button on the front. Using the documentation, I held down the button for over 10 seconds. Didn't reset to factory defaults, tried again and rebooted it, still nothing. What I am I doing wrong. Also nothing comes up on console window and I'm using the setting for Hyper Terminal that the documentation says I should use.
View 5 Replies
View Related
Jun 2, 2013
I want to configure my SRW248G4 switch thru console port. Unfortunately in this switch there is no RJ45 console port input, I can only see cosole port that is look like RS232 input. I bought two standard cisco console cables that have one end with db9 and one with RJ45.
Now I have and idea to put one end of one cable (db9) to switch, and one end (db9) of second cable in my computer (COM input/output)
I need to connect two RJ45 together - this is not a problem, I know how to do this. Here is the question :I know how pinout in my computer look like but i can't find pinout of console port in my SRW248G4. There is many pictures in Internet, for many Cisco devices but this isn't working. Maybe in LINKSYS pinout look different ?
View 3 Replies
View Related
Mar 1, 2012
I am going to purchase SF 300 24p POE Switch and if this Switch supports the configuration via console? As i have ESW-500 Series switches and it does not support console.
View 4 Replies
View Related
Jan 5, 2011
I have had the switch for about 2 years and recently moved. The manual specifies:
38400 bps and 8-n-1 serial port settings using DB9F to DB9F cable.
I have done this and tried using multiple machines/ports/cables as well as several peices of software (minicom, PuTTy, hyperterminal) and none give me any output from the switch at all.
The trouble is that in its original config, it had 1 port locked into its own VLAN for management with port security and an obscure RFC1918 IP address which I cannot recall for the life of me.
At this point, I have no access to TCP/IP management so serial console is my last hope and is not working.
View 2 Replies
View Related
Feb 24, 2013
I have lost the original console cable to the Cisco Linksys SRW2048 and was wondering if I can use the Cisco console cable or can a regular serial cable with female ends will work?
View 2 Replies
View Related
Apr 26, 2011
What kind of cable is required to connect to the Console on a Linksys SRW2024 switch ? ( I've lost the original cable )I use the following settings: Speed 38400, 8 bits, no parity, no flow control and stop bits 1I have tried a serial cable, no go.I have tried a null modem cable with partial handshaking, no go.I have tried a null modem cable with full handshaking, no go.For the null modem cables, if I use it to connect between computers using hyperterminal it works very well. What I type on one computer appears on the other computer's screen.However, I can't get anything out of the switch. I've tried pressing Enter repeatedly, resetting the switch with the Console cable on, etc.
View 2 Replies
View Related
Apr 11, 2010
We have about 30 SRW224G4P switches throughout our network(each one located at remote site) and we have been having problems with these locking up. Normal symptoms are; I can ping the switch but cannot get to the login promot via telnet, ssh, or web-gui even though the ports are open. And how to plugged into the switch after this happens canont reach my router for DHCP.
I did a firmware upgrade to "SRW224G4P_SRW248G4P_image.bix" on one of the switches at our office and this seemed to fix the problems however after the upgrade was compete the config was blank. Is that suppose to happen or did I miss something? I would like to upgrade the firmware on all my our SRW224G4P switches without having to travel to each remote location and reconfigure each switch after the upgrade.
View 6 Replies
View Related
Oct 3, 2012
We have a Cisco SF 300-08 here at work that cannot be used. The system lights are green and flashing. I looked into the manual and pressed the reset button for more than 10 seconds for a factory reset. The port lights lit up momentarily and then goes out. I used Putty and Tera Term with no luck. The screen is just blank; there's no boot up process.
View 2 Replies
View Related
Apr 10, 2012
I configured a new SG-200-08 with a static IP. I tried to save the configuration as the startup configuration. After 10 minutes, I restarted the switch. It didn't boot with the new configuration, and returned to the default .254 and default pw. Now I cannnot assign a new pw or get past the change the pw page. When I try to save a new pw, the switch reboots and prompts me to change from the default pw. I tried resetting the switch by depressing the reset button for a long time, but results are the same. LED indicators are green with a flashing green indicating the .254 address and a solid green on the port where the switch is connected to the computer. How can I reset the switch or get passed the change your pw page?
View 3 Replies
View Related
May 4, 2012
Are there any manuals on how to open the srw224g4p switch? I can't find anything the switch is making a lot of noise - sound like the fan.
View 2 Replies
View Related
Jul 13, 2012
After finishing all of my projects here at work, I decided to finally take a look at a sf300-08 that was left by my predecessor. I almost got into it once via browser but the UI crashed. So I downloaded the manual and proceeded to connect to the switch via rs-232. When I get to the log in screen I cant type anything in and when I try hypterterminal crashes.
View 5 Replies
View Related
Feb 19, 2013
i have a SG300-28 switch here but I do not have the password to login the device. From the startup config of the switch, I see the login password is encrypted. Are there anyway for me to access the device without reset it?
View 2 Replies
View Related
Jan 4, 2012
We just upgraded our Sg300 series switches to the new IOS so we can get CLI access. The upgrade went fine but it seems we have two login prompts, the first being completely unnecessary as you can just hit return to get by it. IE here is the progression:
1. Connect SSH
2. Receive a "login:" prompt. Anything can be entered here, including just return
3. Login banner is displayed
4. Username Prompt is then displayed. Valid username required
5. Password Prompt displayed - Valid password required
6. Now at CLI 1. Connect SSH
I am trying to get rid of that first login prompt (IE Step 2) as it is causing issues with our configuration software. I have tried every line and authentication command I can think of, the only thing that gets rid of it is using none authentication which obviously we can't stay with. how did you get around it?
View 2 Replies
View Related
Dec 16, 2012
We have two 6500 switches and I am unable to login to these switches anymore, but i was able to connect to them yesterday via Telnet. The strange part is that it happened for both switches at the same time.But now when i try to login, it gives me a message "password required, but none set". I can login to them via console.Is it because the 0 - 4 VTY connection are being used and there is no password set from VTY 5 to 15?The config has not changed.
SWITCH-1
line con 0
exec-timeout 0 0
password xxxxx
login
line vty 0 4
[code]....
View 4 Replies
View Related
Apr 20, 2012
Cant log in to my router I've tried 192.168.1.1, 192.168.0.1, (url )Don't know what else I can try keeps poping up with search results. Oh, also tried reseting router and cable modem.
View 5 Replies
View Related
Mar 21, 2011
how can we login into the private network from Remotely in Switches and firewall or Routers,
View 5 Replies
View Related
Jul 31, 2011
I try to login to my router http://192.168.1.1/ I try and put in the user name and password that I think it is. Is it the user name and password you set up or one that's already there and if so where can I find it??
View 6 Replies
View Related
Apr 25, 2011
every time i go to my log in it ask for a pass word i did not make a pass word i have put in all kinds of pass words and got no where it will not even give me a hint i have went to safe mode it still ask for pass word . i have windows 7 how to rid the problem so that i can get around the administrator and remove it so that i can make another administrator account.
View 3 Replies
View Related
Oct 9, 2011
i provide 192.168.1.201 and port No.8150 in CP Plus DVR . I am able to login through Local system via IE with [URL] after pressing enter key Login window appears. I will type User ID as Admin and password 888888. now i am able to enter DVR and view all cameras. no problemin Beetal ADSL router ( ISP Router) i configured port forwarding as followsIP address 192.168.1.201 and Port No. 8150 both internal & external.Now i got internet IP address through MY IP Address.the IP address is 59.92.67.72 ISPs IP address for my Borad Band.through another internet with different different ISPI open IE and type [URL] got same loging window as in LANagain I enter User Id as Admin and password 888888but shows login failed Message through internet I got the same login window when i tried through LAN, but I am to unable login with a message login failed
View 1 Replies
View Related
