Cisco Switches :: Cannot Login To SF 300-08
Oct 3, 2012
We have a Cisco SF 300-08 here at work that cannot be used. The system lights are green and flashing. I looked into the manual and pressed the reset button for more than 10 seconds for a factory reset. The port lights lit up momentarily and then goes out. I used Putty and Tera Term with no luck. The screen is just blank; there's no boot up process.
View 2 Replies
ADVERTISEMENT
Apr 10, 2012
I configured a new SG-200-08 with a static IP. I tried to save the configuration as the startup configuration. After 10 minutes, I restarted the switch. It didn't boot with the new configuration, and returned to the default .254 and default pw. Now I cannnot assign a new pw or get past the change the pw page. When I try to save a new pw, the switch reboots and prompts me to change from the default pw. I tried resetting the switch by depressing the reset button for a long time, but results are the same. LED indicators are green with a flashing green indicating the .254 address and a solid green on the port where the switch is connected to the computer. How can I reset the switch or get passed the change your pw page?
View 3 Replies
View Related
Jul 13, 2012
After finishing all of my projects here at work, I decided to finally take a look at a sf300-08 that was left by my predecessor. I almost got into it once via browser but the UI crashed. So I downloaded the manual and proceeded to connect to the switch via rs-232. When I get to the log in screen I cant type anything in and when I try hypterterminal crashes.
View 5 Replies
View Related
Feb 19, 2013
i have a SG300-28 switch here but I do not have the password to login the device. From the startup config of the switch, I see the login password is encrypted. Are there anyway for me to access the device without reset it?
View 2 Replies
View Related
Jan 4, 2012
We just upgraded our Sg300 series switches to the new IOS so we can get CLI access. The upgrade went fine but it seems we have two login prompts, the first being completely unnecessary as you can just hit return to get by it. IE here is the progression:
1. Connect SSH
2. Receive a "login:" prompt. Anything can be entered here, including just return
3. Login banner is displayed
4. Username Prompt is then displayed. Valid username required
5. Password Prompt displayed - Valid password required
6. Now at CLI 1. Connect SSH
I am trying to get rid of that first login prompt (IE Step 2) as it is causing issues with our configuration software. I have tried every line and authentication command I can think of, the only thing that gets rid of it is using none authentication which obviously we can't stay with. how did you get around it?
View 2 Replies
View Related
Dec 16, 2012
We have two 6500 switches and I am unable to login to these switches anymore, but i was able to connect to them yesterday via Telnet. The strange part is that it happened for both switches at the same time.But now when i try to login, it gives me a message "password required, but none set". I can login to them via console.Is it because the 0 - 4 VTY connection are being used and there is no password set from VTY 5 to 15?The config has not changed.
SWITCH-1
line con 0
exec-timeout 0 0
password xxxxx
login
line vty 0 4
[code]....
View 4 Replies
View Related
Jun 8, 2011
The switch functions and operates fine but I can no longer login to the webview(GUI) and when I use a serial cable to console in to it, it shows nothing on the hyperterminal meaning no login. How can I get back into the switch to manage it or reset it back to factory settings? I kept the default IP address and I enabled HTTPS to login by gui, well I got in by HTTPS so I went in to turn that setting off and hit apply and now I can't log into it at all.
View 1 Replies
View Related
Apr 20, 2012
Cant log in to my router I've tried 192.168.1.1, 192.168.0.1, (url )Don't know what else I can try keeps poping up with search results. Oh, also tried reseting router and cable modem.
View 5 Replies
View Related
Mar 21, 2011
how can we login into the private network from Remotely in Switches and firewall or Routers,
View 5 Replies
View Related
Jul 31, 2011
I try to login to my router http://192.168.1.1/ I try and put in the user name and password that I think it is. Is it the user name and password you set up or one that's already there and if so where can I find it??
View 6 Replies
View Related
Apr 25, 2011
every time i go to my log in it ask for a pass word i did not make a pass word i have put in all kinds of pass words and got no where it will not even give me a hint i have went to safe mode it still ask for pass word . i have windows 7 how to rid the problem so that i can get around the administrator and remove it so that i can make another administrator account.
View 3 Replies
View Related
Oct 9, 2011
i provide 192.168.1.201 and port No.8150 in CP Plus DVR . I am able to login through Local system via IE with [URL] after pressing enter key Login window appears. I will type User ID as Admin and password 888888. now i am able to enter DVR and view all cameras. no problemin Beetal ADSL router ( ISP Router) i configured port forwarding as followsIP address 192.168.1.201 and Port No. 8150 both internal & external.Now i got internet IP address through MY IP Address.the IP address is 59.92.67.72 ISPs IP address for my Borad Band.through another internet with different different ISPI open IE and type [URL] got same loging window as in LANagain I enter User Id as Admin and password 888888but shows login failed Message through internet I got the same login window when i tried through LAN, but I am to unable login with a message login failed
View 1 Replies
View Related
Feb 10, 2012
I have a website account with fatcow. I created the website with Dreamweaver software and uploaded it to fatcow via port 21.My internet connection was via xplornet and I had no access problems. I upgraded to xplornet's new g4 system and now I can no longer access my account online or upload to my website.We have two computers. The first is a desktop system that has the dreamweaver software. The second is a laptop which connects wirelessly. We share the signal through a dlink router. The modem is a viasat Surfbeam 2 residential satellite modem.1. When I attempt to login to the fatcow control panel, the tab shows successfully authenticated and then re-directs me back to the login page. This happens on both the laptop and the desktop.
I have tried bypassing the router and the problem still exists.I took the laptop to the computer center and I can login to the account no problem.I used a free proxy server page on the internet and can login from my home system on my desktop no problem.I have completely turned off virus scan and firewalls. It doesn't work. I have tried IE7, Chrome, Firefox and they all have the same problem. The laptop runs IE8 and has the same problem.I can ping the page successfully. I can traceroute the page successfully. I can't nslooup any site at all. I get the domain not existant message.My ip and dns settings are the automatically find option.I have renewed ips and dumped the dns cache.Using alternate dns addresses doesn't rectify the problem. When I attempt to upload via dreamweaver, I connect but within seconds I get a Dreamweaver message that says "Connection to remote host has been lost. Click refresh to continue" and the log reads "FTP Error. Dreamweaver could not connect to server." I haven't taken my desktop anywhere to try to see if it works on a different network. I'm in a remote location (hence the satellite internet)and it is an hours drive to the nearest private internet connection and a 2 hour drive to the nearest public connection.
View 19 Replies
View Related
May 9, 2013
We have a Linksys WRT120N wireless router set up at one of our small offices. I noticed recently when trying to log in to the router to make some admin configurations that it will not accept the login credentials when trying to log in from IE10 browser. Works fine from Chrome, IE9, ect. logging in to a linksys router with IE10?
View 3 Replies
View Related
Jun 4, 2012
I can login into the console just fine but if I try and login into the server via the web [URL] it tells me invalid username or password.
During setup I left the username default and set the password. Then it asked me for the password to login to the web but it never asked me the username to use. I have to set this up very soon.
View 2 Replies
View Related
Jan 23, 2012
Without previous versions the ssh login user was pix, without AAA.Now with ASA 8.4 ?
View 3 Replies
View Related
May 18, 2013
I have an issue with accessing a Cisco NCS (ver.1.3.0.20) form the GUI interface. It claim the password is wrong...From the CLI I have access.... Ah I can just change the passwords I thought. But no way.. dosent work!
[code]...
View 6 Replies
View Related
Oct 14, 2012
I have installed LMS4.2.2 on Windows 2008 server and am unable to login via the 'admin' username. I get "Invalid Username or Password. Please try again" error message. I can successfully login using Windows AD username and password.
I have reset the password for 'admin' username with the following:
!
nmsrootinperl.exe resetpasswd.pl admin
Server has been rebooted PRE and POST password reset.
View 2 Replies
View Related
Aug 25, 2011
i have 2960 Catalyst with LANLITE. And i cannot set "transport input ssh", it allows only telnet. I'm wondering if cisco lanlite switches have ssh input in newer releases of IOS or there is no way to make ssh input on this switch?Here's show ver output (i removed all serial and part numbers):
S14#sh ver
Cisco IOS Software, C2960 Software (C2960-LANLITE-M), Version 12.2(37)EY, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 28-Jun-07 18:07 by antonino
Image text-base: 0x00003000, data-base: 0x00D00000
[code]....
View 2 Replies
View Related
Feb 12, 2012
how can I import a public or private key in a router? For example, a Cisco 3560th I have found some conflicting answers @ cisco.com . Background, I would like to login with PUTTY via ssh on a Cisco Router but without username and password.The login should be made with RSA Keys. For this I need to deposit on the IOS device's the public key and on my Client the private key. For this I've already created with PuTTYGen the two keys. The private is in the ppk format. I still need to convert this into a different format? Since there are PEM and PKCS. Below you can see what times I have entered. With the error message: "CRYPTO_PKI: Import PKCS12 operation failed, failure status = 0x705" With the following error message I can do anything?
View 2 Replies
View Related
Dec 5, 2011
i recently upgraded our Ciscoworks LMS from 4.0 to 4.1. after i installed the upgrade the admin login doesnt work, neither does any other account. i have tried resetting the password but it doesnt work.
View 3 Replies
View Related
May 13, 2013
I'm using ASA 902, and I deploy any connect ssl only and no IPSec... It always open only connection if you start via browser, you cannot reconnect using installed software.
View 2 Replies
View Related
Aug 28, 2012
I'm crazy with this version of ACS, it is totally diferent than ACS 4.2, which is familiar for me and seems to difficult to config for me.Although I have red a lot of post about problems with the integration WCS 7.0 and ACS 5.2 using TACACs+ for admin or lobby access to the web portal I can't do login into WCS as Lobby ambassador using ACS 5.2 because always show me the error "User has no usergroups assigned".Steps I followed:
- I create a "shell profile" with the custom attributes of the group "lobby ambassador".
- In default device admin / authorization, I create a rule matching this "shell profile".
I see lot os Hit counts and passed in logs, but the message written previously.In ACS 4.2 I had to create the custom attribute "HTTP" and string "Wireless- WCS" to work with, but now I don't know if it is necessary and I don't know how to do it.
View 5 Replies
View Related
Mar 5, 2013
I have an ASA 5505 that is hosting a SSL VPN. The user can not login. They receive login error. To the best of their knowledge, this problem started after the office Domain Controller was rebuilt. I have looked on ASA and in AD and cannot seem to trace the issue.
View 9 Replies
View Related
Apr 14, 2011
Our VPN 3000 concentrator's admin password was changed by somebody so i reset the password by using straight through serial cable, now the problem is it allows me to login with admin through console but not through admin web interface or telnet. I have enabled telnet and http access but still no success. Concentrator is using internal database so no AAA server is configured.
View 1 Replies
View Related
Sep 4, 2012
After clearing the Browser-Cache I cant get to the Home page when I login to LMS3.2. Instead of the Homepage following is showing: NOT FOUND Unable to find URL. The selected View has been deleted or Friendly URL has been modified.
View 1 Replies
View Related
Jun 21, 2012
We are facing an issue with the NAM3.Version: 5.1(2-patch4)
we can not login using the GUI. when we try to login we are getting the following warning:
Initializing database. Please wait until initialization process finishes.(see attachment)
we have rebooted the NAM3 module but the issue is not solved. the NAM3 module is running on 6500 Series Switch.(Cisco Catalyst 6500 Series Network Analysis Module (NAM-3)
View 5 Replies
View Related
Apr 24, 2011
I have two ACS 5.2 working in redundancy Primary and Secondary my question in when my primary ACS goes down i can´t see the log in the secondary ACS. I read in the documentación that only one ACS can be configurated for working like logg collector server. Now I configurated my secondary ACS like logg collector server now when my Primary ACS goes down i can see the logg. Finally when my Secondary ACS goes down i can modified the ACS Primary Configution by show me the logg.. Is possible to do this automaticaly for show me the event logg ? when the ACS that is configurate like logg collector server goes down pass the event other ACS automatically..
View 3 Replies
View Related
Dec 12, 2012
I am having issue logging into my Cisco ASA 5505 ASDM interface. It prompts for a username and password but it will not authenticate. When I look at the http debug it tells me that authentication failed. I have tried with both username and password as well as with just a password.
View 6 Replies
View Related
Feb 17, 2011
Ok so i just got a 1841 and i have nfc where to start on hwo to set it up or make it work. How do i go about loging in to it so i can set it up to use it as a router? I tried to plug my pc in to the consle port and my pc doesn't even show i have any thing hooked up to it. so any step by step guides on how to log in and set this up?
View 19 Replies
View Related
Jun 1, 2013
Few days ago in my wireless infrastrucer i deploy Cisco ACS 5.0 with Active directory integration. My wireless users are login through web authentication process. The authentication process is passed by AD & its working fine. But i want to do a work on my ACS 5.0 that a user cannot login simultaneously multiple device at a time.
View 21 Replies
View Related
Apr 9, 2011
Act I m working in a telecomm company. Where some telecomm monitoring software running on WAN fixed IP. Now i want to remotely use that PC with another PC having normal another internet connection. Is it possible? My one friend tried it using TEAM VIEWER by setting proxy address in team viewer but that proxy address is not working now.
View 1 Replies
View Related
Nov 14, 2012
"how to monitoring VPN Login Session?" I want to the history of VPN User login to my VPN. How could I know?Which software can made me easy to monitoring and store those log in my SNMP Server? How to do that?
View 1 Replies
View Related