Cisco Firewall :: 8.4 And SSH Login Without ASA?
Jan 23, 2012Without previous versions the ssh login user was pix, without AAA.Now with ASA 8.4 ?
View 3 RepliesWithout previous versions the ssh login user was pix, without AAA.Now with ASA 8.4 ?
View 3 RepliesI'm using ASA 902, and I deploy any connect ssl only and no IPSec... It always open only connection if you start via browser, you cannot reconnect using installed software.
View 2 Replies View RelatedI have not worked with ASDM in a while. I have a 5510, with asdm-645.bin in the flash. The device runs version 8.4(2). I can download ASDM from the http interface of the firewall from the management interface. But I can not log in. I have used blank username and password, no username and enable password, blank username with enable password and a few other permutations. I then tried to connect to the asdm interface from inside also. But I can not connect. Needless to say, I have enabled http, and updated the http access-list. The only logging I have enabled is buffered. Is there any configuration that I am missing? Shall I cut and past the config?
View 4 Replies View RelatedI have an ASA Firewall 5520 and to add or edit configuration, I use the ASDM interface. For some reason, the admin password that I use is no longer working. The last time I logged on to the firewall was last week and I am the only person with access to it. I used a backup account to login and was able to, but on the menu bar the "Configuration" button is missing.
View 2 Replies View RelatedI am running 9.11 and I have created users with password but it has no effect on the SSH Login!I don't get it... What am I missing?
View 3 Replies View Relatedi have in my network firewall ASA 5510 but the problem i cannot login to my firewall thru telnet or ssh even ASDM or bowser this is my configuration :
ASA Version 8.2(5)
!
hostname Amco-ASA
[Code].....
I am having two dc switches with FWSM modules installed. DC switch1 FWSM (Ver 3.2(12) is wokring as active and Secondary DC switch2 FWSM (ver 3.2.(12) is in standby mode.
From yesterday I am trying to login primary FWSM, It is accepting my username and credentials but prompting again for username please refer below
DXB-DC1>session slot 5 p 1The default escape character is Ctrl-^, then x.You can also type 'exit' at the remote prompt to end the sessionTrying 127.0.0.51 Open. [code]
Is there a way to reset the device and start all over again. The person who set this up is no longer with the companyand did not detail the information. We installed a new t1 line with new IP addresses and need to set this to connectwith our remote location. And I am not knowledgeable at all on how to configure this.
View 1 Replies View RelatedI have a website account with fatcow. I created the website with Dreamweaver software and uploaded it to fatcow via port 21.My internet connection was via xplornet and I had no access problems. I upgraded to xplornet's new g4 system and now I can no longer access my account online or upload to my website.We have two computers. The first is a desktop system that has the dreamweaver software. The second is a laptop which connects wirelessly. We share the signal through a dlink router. The modem is a viasat Surfbeam 2 residential satellite modem.1. When I attempt to login to the fatcow control panel, the tab shows successfully authenticated and then re-directs me back to the login page. This happens on both the laptop and the desktop.
I have tried bypassing the router and the problem still exists.I took the laptop to the computer center and I can login to the account no problem.I used a free proxy server page on the internet and can login from my home system on my desktop no problem.I have completely turned off virus scan and firewalls. It doesn't work. I have tried IE7, Chrome, Firefox and they all have the same problem. The laptop runs IE8 and has the same problem.I can ping the page successfully. I can traceroute the page successfully. I can't nslooup any site at all. I get the domain not existant message.My ip and dns settings are the automatically find option.I have renewed ips and dumped the dns cache.Using alternate dns addresses doesn't rectify the problem. When I attempt to upload via dreamweaver, I connect but within seconds I get a Dreamweaver message that says "Connection to remote host has been lost. Click refresh to continue" and the log reads "FTP Error. Dreamweaver could not connect to server." I haven't taken my desktop anywhere to try to see if it works on a different network. I'm in a remote location (hence the satellite internet)and it is an hours drive to the nearest private internet connection and a 2 hour drive to the nearest public connection.
We have a Linksys WRT120N wireless router set up at one of our small offices. I noticed recently when trying to log in to the router to make some admin configurations that it will not accept the login credentials when trying to log in from IE10 browser. Works fine from Chrome, IE9, ect. logging in to a linksys router with IE10?
View 3 Replies View RelatedI have Cisco5510 running with ADSM 6.0 version, I was able to access it fine since few months but suddenly I am unable to login through that.Its prompting for username and password and loading it to 100% but not opening the GUI console.I feel this could be the JAVA version issue but with the same version of JAVA I am able run another ASA 5520 which is running with 6.4ASDM version.Request you to suggest the right JAVA version to run 5510 with ASDM 6.0 GUI console.
View 1 Replies View RelatedI got an ASA 5505 recently and i'm new to using firewalls but have forgotten the username and password that was set on it for login using SSH (putty). Is there a way i can stiil login to it or even reset the password so i can login using Putty?
View 1 Replies View RelatedI have added Cisco 5520 into the Cisco ACS 4.2 Tacacs Server. I can login to the user mode, but I can't login to the privilege mode ? though I have put enable password, but when I use that password, no joy ?
View 3 Replies View RelatedWhen i tried to login through ASDM at Cisco ASA 5510, it ask for the username and password and after that nothing comes up. I am able to login through ssh. [code]
As per my knowledge show bootvar and show version, should shows the same IOS version. But here it's showing different. Is asdm-523 is compatible with IOS asa708.
We've a Cisco ASA 5505 connected directly to Verizon FiOS Circuit (ONT) box using Ethernet cable. As per the existing documention that I have, the previous configured this as a dedicated router to establish a seperate VPN connection our software provider. They assigned both Public Static and Local Static IP address. When I try to ping the public IP address, it says request time out; so the public IP address is no longer working.
When I ping the local IP address of 192.168.100.11, it responds. The SolarWind tool also shows Always UP signal. How can I login into this router either from remotely or locally to check the configuration, backup and do the fimrware upgrade?
I also tried to connect my laptop directly to the ASA 5505 router LAN port. After 3 minutes, I'm able to connect to Internet without any issues. However I don't know the IP address to use to login.
I am running the Startup Wizard from my browser as I do not have a Console Access for a brand new CISCO ASA and I am stucked with the User? Password ? I tried many combination and nothing worked.
View 1 Replies View RelatedI can login into the console just fine but if I try and login into the server via the web [URL] it tells me invalid username or password.
During setup I left the username default and set the password. Then it asked me for the password to login to the web but it never asked me the username to use. I have to set this up very soon.
We have a Cisco SF 300-08 here at work that cannot be used. The system lights are green and flashing. I looked into the manual and pressed the reset button for more than 10 seconds for a factory reset. The port lights lit up momentarily and then goes out. I used Putty and Tera Term with no luck. The screen is just blank; there's no boot up process.
View 2 Replies View RelatedI have an issue with accessing a Cisco NCS (ver.1.3.0.20) form the GUI interface. It claim the password is wrong...From the CLI I have access.... Ah I can just change the passwords I thought. But no way.. dosent work!
[code]...
I have installed LMS4.2.2 on Windows 2008 server and am unable to login via the 'admin' username. I get "Invalid Username or Password. Please try again" error message. I can successfully login using Windows AD username and password.
I have reset the password for 'admin' username with the following:
!
nmsrootinperl.exe resetpasswd.pl admin
Server has been rebooted PRE and POST password reset.
i have 2960 Catalyst with LANLITE. And i cannot set "transport input ssh", it allows only telnet. I'm wondering if cisco lanlite switches have ssh input in newer releases of IOS or there is no way to make ssh input on this switch?Here's show ver output (i removed all serial and part numbers):
S14#sh ver
Cisco IOS Software, C2960 Software (C2960-LANLITE-M), Version 12.2(37)EY, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 28-Jun-07 18:07 by antonino
Image text-base: 0x00003000, data-base: 0x00D00000
[code]....
how can I import a public or private key in a router? For example, a Cisco 3560th I have found some conflicting answers @ cisco.com . Background, I would like to login with PUTTY via ssh on a Cisco Router but without username and password.The login should be made with RSA Keys. For this I need to deposit on the IOS device's the public key and on my Client the private key. For this I've already created with PuTTYGen the two keys. The private is in the ppk format. I still need to convert this into a different format? Since there are PEM and PKCS. Below you can see what times I have entered. With the error message: "CRYPTO_PKI: Import PKCS12 operation failed, failure status = 0x705" With the following error message I can do anything?
View 2 Replies View Relatedi recently upgraded our Ciscoworks LMS from 4.0 to 4.1. after i installed the upgrade the admin login doesnt work, neither does any other account. i have tried resetting the password but it doesnt work.
View 3 Replies View RelatedI configured a new SG-200-08 with a static IP. I tried to save the configuration as the startup configuration. After 10 minutes, I restarted the switch. It didn't boot with the new configuration, and returned to the default .254 and default pw. Now I cannnot assign a new pw or get past the change the pw page. When I try to save a new pw, the switch reboots and prompts me to change from the default pw. I tried resetting the switch by depressing the reset button for a long time, but results are the same. LED indicators are green with a flashing green indicating the .254 address and a solid green on the port where the switch is connected to the computer. How can I reset the switch or get passed the change your pw page?
View 3 Replies View RelatedI'm crazy with this version of ACS, it is totally diferent than ACS 4.2, which is familiar for me and seems to difficult to config for me.Although I have red a lot of post about problems with the integration WCS 7.0 and ACS 5.2 using TACACs+ for admin or lobby access to the web portal I can't do login into WCS as Lobby ambassador using ACS 5.2 because always show me the error "User has no usergroups assigned".Steps I followed:
- I create a "shell profile" with the custom attributes of the group "lobby ambassador".
- In default device admin / authorization, I create a rule matching this "shell profile".
I see lot os Hit counts and passed in logs, but the message written previously.In ACS 4.2 I had to create the custom attribute "HTTP" and string "Wireless- WCS" to work with, but now I don't know if it is necessary and I don't know how to do it.
I have an ASA 5505 that is hosting a SSL VPN. The user can not login. They receive login error. To the best of their knowledge, this problem started after the office Domain Controller was rebuilt. I have looked on ASA and in AD and cannot seem to trace the issue.
View 9 Replies View RelatedOur VPN 3000 concentrator's admin password was changed by somebody so i reset the password by using straight through serial cable, now the problem is it allows me to login with admin through console but not through admin web interface or telnet. I have enabled telnet and http access but still no success. Concentrator is using internal database so no AAA server is configured.
View 1 Replies View RelatedAfter clearing the Browser-Cache I cant get to the Home page when I login to LMS3.2. Instead of the Homepage following is showing: NOT FOUND Unable to find URL. The selected View has been deleted or Friendly URL has been modified.
View 1 Replies View RelatedWe are facing an issue with the NAM3.Version: 5.1(2-patch4)
we can not login using the GUI. when we try to login we are getting the following warning:
Initializing database. Please wait until initialization process finishes.(see attachment)
we have rebooted the NAM3 module but the issue is not solved. the NAM3 module is running on 6500 Series Switch.(Cisco Catalyst 6500 Series Network Analysis Module (NAM-3)
I have two ACS 5.2 working in redundancy Primary and Secondary my question in when my primary ACS goes down i can´t see the log in the secondary ACS. I read in the documentación that only one ACS can be configurated for working like logg collector server. Now I configurated my secondary ACS like logg collector server now when my Primary ACS goes down i can see the logg. Finally when my Secondary ACS goes down i can modified the ACS Primary Configution by show me the logg.. Is possible to do this automaticaly for show me the event logg ? when the ACS that is configurate like logg collector server goes down pass the event other ACS automatically..
View 3 Replies View RelatedI am having issue logging into my Cisco ASA 5505 ASDM interface. It prompts for a username and password but it will not authenticate. When I look at the http debug it tells me that authentication failed. I have tried with both username and password as well as with just a password.
View 6 Replies View RelatedOk so i just got a 1841 and i have nfc where to start on hwo to set it up or make it work. How do i go about loging in to it so i can set it up to use it as a router? I tried to plug my pc in to the consle port and my pc doesn't even show i have any thing hooked up to it. so any step by step guides on how to log in and set this up?
View 19 Replies View RelatedFew days ago in my wireless infrastrucer i deploy Cisco ACS 5.0 with Active directory integration. My wireless users are login through web authentication process. The authentication process is passed by AD & its working fine. But i want to do a work on my ACS 5.0 that a user cannot login simultaneously multiple device at a time.
View 21 Replies View Related