I can login into the console just fine but if I try and login into the server via the web [URL] it tells me invalid username or password.
During setup I left the username default and set the password. Then it asked me for the password to login to the web but it never asked me the username to use. I have to set this up very soon.
I did an ISE 1.1.1 installation on a VMWare with ESX 5.0. After installation I am not able to login with my credentials(username admin, password XXXX) I can ping my ISE server after initial installation but I can not ping my ISE server after full installation.I did the installation several times and even did it on a VM with differrent VMversion.
View 3 Replies View RelatedI have a website account with fatcow. I created the website with Dreamweaver software and uploaded it to fatcow via port 21.My internet connection was via xplornet and I had no access problems. I upgraded to xplornet's new g4 system and now I can no longer access my account online or upload to my website.We have two computers. The first is a desktop system that has the dreamweaver software. The second is a laptop which connects wirelessly. We share the signal through a dlink router. The modem is a viasat Surfbeam 2 residential satellite modem.1. When I attempt to login to the fatcow control panel, the tab shows successfully authenticated and then re-directs me back to the login page. This happens on both the laptop and the desktop.
I have tried bypassing the router and the problem still exists.I took the laptop to the computer center and I can login to the account no problem.I used a free proxy server page on the internet and can login from my home system on my desktop no problem.I have completely turned off virus scan and firewalls. It doesn't work. I have tried IE7, Chrome, Firefox and they all have the same problem. The laptop runs IE8 and has the same problem.I can ping the page successfully. I can traceroute the page successfully. I can't nslooup any site at all. I get the domain not existant message.My ip and dns settings are the automatically find option.I have renewed ips and dumped the dns cache.Using alternate dns addresses doesn't rectify the problem. When I attempt to upload via dreamweaver, I connect but within seconds I get a Dreamweaver message that says "Connection to remote host has been lost. Click refresh to continue" and the log reads "FTP Error. Dreamweaver could not connect to server." I haven't taken my desktop anywhere to try to see if it works on a different network. I'm in a remote location (hence the satellite internet)and it is an hours drive to the nearest private internet connection and a 2 hour drive to the nearest public connection.
We have a Linksys WRT120N wireless router set up at one of our small offices. I noticed recently when trying to log in to the router to make some admin configurations that it will not accept the login credentials when trying to log in from IE10 browser. Works fine from Chrome, IE9, ect. logging in to a linksys router with IE10?
View 3 Replies View RelatedWe have a Cisco SF 300-08 here at work that cannot be used. The system lights are green and flashing. I looked into the manual and pressed the reset button for more than 10 seconds for a factory reset. The port lights lit up momentarily and then goes out. I used Putty and Tera Term with no luck. The screen is just blank; there's no boot up process.
View 2 Replies View RelatedWithout previous versions the ssh login user was pix, without AAA.Now with ASA 8.4 ?
View 3 Replies View RelatedI have an issue with accessing a Cisco NCS (ver.1.3.0.20) form the GUI interface. It claim the password is wrong...From the CLI I have access.... Ah I can just change the passwords I thought. But no way.. dosent work!
[code]...
I have installed LMS4.2.2 on Windows 2008 server and am unable to login via the 'admin' username. I get "Invalid Username or Password. Please try again" error message. I can successfully login using Windows AD username and password.
I have reset the password for 'admin' username with the following:
!
nmsrootinperl.exe resetpasswd.pl admin
Server has been rebooted PRE and POST password reset.
i have 2960 Catalyst with LANLITE. And i cannot set "transport input ssh", it allows only telnet. I'm wondering if cisco lanlite switches have ssh input in newer releases of IOS or there is no way to make ssh input on this switch?Here's show ver output (i removed all serial and part numbers):
S14#sh ver
Cisco IOS Software, C2960 Software (C2960-LANLITE-M), Version 12.2(37)EY, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 28-Jun-07 18:07 by antonino
Image text-base: 0x00003000, data-base: 0x00D00000
[code]....
how can I import a public or private key in a router? For example, a Cisco 3560th I have found some conflicting answers @ cisco.com . Background, I would like to login with PUTTY via ssh on a Cisco Router but without username and password.The login should be made with RSA Keys. For this I need to deposit on the IOS device's the public key and on my Client the private key. For this I've already created with PuTTYGen the two keys. The private is in the ppk format. I still need to convert this into a different format? Since there are PEM and PKCS. Below you can see what times I have entered. With the error message: "CRYPTO_PKI: Import PKCS12 operation failed, failure status = 0x705" With the following error message I can do anything?
View 2 Replies View Relatedi recently upgraded our Ciscoworks LMS from 4.0 to 4.1. after i installed the upgrade the admin login doesnt work, neither does any other account. i have tried resetting the password but it doesnt work.
View 3 Replies View RelatedI configured a new SG-200-08 with a static IP. I tried to save the configuration as the startup configuration. After 10 minutes, I restarted the switch. It didn't boot with the new configuration, and returned to the default .254 and default pw. Now I cannnot assign a new pw or get past the change the pw page. When I try to save a new pw, the switch reboots and prompts me to change from the default pw. I tried resetting the switch by depressing the reset button for a long time, but results are the same. LED indicators are green with a flashing green indicating the .254 address and a solid green on the port where the switch is connected to the computer. How can I reset the switch or get passed the change your pw page?
View 3 Replies View RelatedI'm using ASA 902, and I deploy any connect ssl only and no IPSec... It always open only connection if you start via browser, you cannot reconnect using installed software.
View 2 Replies View RelatedI'm crazy with this version of ACS, it is totally diferent than ACS 4.2, which is familiar for me and seems to difficult to config for me.Although I have red a lot of post about problems with the integration WCS 7.0 and ACS 5.2 using TACACs+ for admin or lobby access to the web portal I can't do login into WCS as Lobby ambassador using ACS 5.2 because always show me the error "User has no usergroups assigned".Steps I followed:
- I create a "shell profile" with the custom attributes of the group "lobby ambassador".
- In default device admin / authorization, I create a rule matching this "shell profile".
I see lot os Hit counts and passed in logs, but the message written previously.In ACS 4.2 I had to create the custom attribute "HTTP" and string "Wireless- WCS" to work with, but now I don't know if it is necessary and I don't know how to do it.
I have an ASA 5505 that is hosting a SSL VPN. The user can not login. They receive login error. To the best of their knowledge, this problem started after the office Domain Controller was rebuilt. I have looked on ASA and in AD and cannot seem to trace the issue.
View 9 Replies View RelatedOur VPN 3000 concentrator's admin password was changed by somebody so i reset the password by using straight through serial cable, now the problem is it allows me to login with admin through console but not through admin web interface or telnet. I have enabled telnet and http access but still no success. Concentrator is using internal database so no AAA server is configured.
View 1 Replies View RelatedAfter clearing the Browser-Cache I cant get to the Home page when I login to LMS3.2. Instead of the Homepage following is showing: NOT FOUND Unable to find URL. The selected View has been deleted or Friendly URL has been modified.
View 1 Replies View RelatedWe are facing an issue with the NAM3.Version: 5.1(2-patch4)
we can not login using the GUI. when we try to login we are getting the following warning:
Initializing database. Please wait until initialization process finishes.(see attachment)
we have rebooted the NAM3 module but the issue is not solved. the NAM3 module is running on 6500 Series Switch.(Cisco Catalyst 6500 Series Network Analysis Module (NAM-3)
I have two ACS 5.2 working in redundancy Primary and Secondary my question in when my primary ACS goes down i can´t see the log in the secondary ACS. I read in the documentación that only one ACS can be configurated for working like logg collector server. Now I configurated my secondary ACS like logg collector server now when my Primary ACS goes down i can see the logg. Finally when my Secondary ACS goes down i can modified the ACS Primary Configution by show me the logg.. Is possible to do this automaticaly for show me the event logg ? when the ACS that is configurate like logg collector server goes down pass the event other ACS automatically..
View 3 Replies View RelatedI am having issue logging into my Cisco ASA 5505 ASDM interface. It prompts for a username and password but it will not authenticate. When I look at the http debug it tells me that authentication failed. I have tried with both username and password as well as with just a password.
View 6 Replies View RelatedOk so i just got a 1841 and i have nfc where to start on hwo to set it up or make it work. How do i go about loging in to it so i can set it up to use it as a router? I tried to plug my pc in to the consle port and my pc doesn't even show i have any thing hooked up to it. so any step by step guides on how to log in and set this up?
View 19 Replies View RelatedFew days ago in my wireless infrastrucer i deploy Cisco ACS 5.0 with Active directory integration. My wireless users are login through web authentication process. The authentication process is passed by AD & its working fine. But i want to do a work on my ACS 5.0 that a user cannot login simultaneously multiple device at a time.
View 21 Replies View RelatedAct I m working in a telecomm company. Where some telecomm monitoring software running on WAN fixed IP. Now i want to remotely use that PC with another PC having normal another internet connection. Is it possible? My one friend tried it using TEAM VIEWER by setting proxy address in team viewer but that proxy address is not working now.
View 1 Replies View Related"how to monitoring VPN Login Session?" I want to the history of VPN User login to my VPN. How could I know?Which software can made me easy to monitoring and store those log in my SNMP Server? How to do that?
View 1 Replies View RelatedWe are unable to login at Cisco 6509 switch, due to username and password not working. We have tried to recover the password as per Cisco document, but that is also not working. This switch is our Primary Switch in our network.
View 8 Replies View Relatedcustomize the login page for the ssl-vpn as mentioned. When the vpn is set up, the default template allows my customers users to login with this : IMAGE 1
While trying to edit the login page, I have to create a new Customization file from CLIENTLESS SSL VPN ACCESS -> PORTAL -> CUSTOMIZATION in the ASDM. When I do that and I try to edit the login page, it comes up with 2 forms of authentication and an internal password prompt like this: IMAGE 2
How can I edit the login page I created so that users will only see the regular username and password fields like the default template?
I'm using NAC 4.8, and I'd like to login using NAC Web Agent on Ipad. When I'm trying to do that, I'm receiving a message on Ipad that I need to install Java Plug-In, but there is no JavaPlug-in available for Ipad. Any additional configuration that I have to do on NAC Manager to be able to access the network using NAC Web Login on Ipad ?
View 3 Replies View RelatedI have not worked with ASDM in a while. I have a 5510, with asdm-645.bin in the flash. The device runs version 8.4(2). I can download ASDM from the http interface of the firewall from the management interface. But I can not log in. I have used blank username and password, no username and enable password, blank username with enable password and a few other permutations. I then tried to connect to the asdm interface from inside also. But I can not connect. Needless to say, I have enabled http, and updated the http access-list. The only logging I have enabled is buffered. Is there any configuration that I am missing? Shall I cut and past the config?
View 4 Replies View RelatedCisco cannot login? Currently i cannot login to the two of my cisco 3560 with the password that i usually used to login. and it is strength to me that its Configuration register is 0xF.
[BEGIN] 10/4/2011 10:22:57 AMshoTC-NGN-C3560-1>show verTC-NGN-C3560-1>show version Cisco IOS Software, C3560 Software (C3560-IPSERVICES-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2007 by Cisco Systems, Inc.Compiled Thu 19-Jul-07 18:15 by nachenImage text-base: 0x00003000, data-base: 0x01300000
ROM: Bootstrap program is C3560 boot loaderBOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(25r)SEC, RELEASE SOFTWARE (fc4)
TC-NGN-C3560-1 uptime is 50 weeks, 6 days, 9 hours, 34 minutesSystem returned to ROM by power-onSystem image file is "flash:c3560-ipservices-mz.122-35.SE5/c3560-ipservices-mz.122-35.SE5.bin"
[code]....
We are using the ASA 5520 as Firewall and VPN gateway for remote access by employees and vendors. Is there a way to view a history of VPN user logins? We used to have (or we still have but no longer using it) th CVPN 3005. This device keeps log files of all activities. I miss having this capability in the ASA 5520.
View 4 Replies View RelatedI have an ASA5510 that I am trying to set up for remote access using SSL VPN & clientless SSL VPN. I have followed the config guides on the Cisco website as well as the config guides elsewhere on the internet to no avail. I have a TAC case opened and have spoken with 4 engineers thus far. I have tried several software versions on the device and they all give the same result.When going to https://(outside interface ip address), I receive the expected ssl certificate error, then I click to continue to the website, and the browser never loads a page. I can see the ssl negotiation in my debug, and it completes that portion. My http debug shows the get requests to https://(outside interface ip address)/+CSCOE+/index.html and/or logon.html, but the page never loads.
View 7 Replies View RelatedI configured my ACS 5.1 correctly, but I get an "Access is denied to NCS" at the web login page. In the ACS i see a successful authentication.
View 14 Replies View RelatedI have just set up my Cisco 1941 router to my cable internet connection. I have access to everything, but I cant login successfully into Cisco CP.
I set up a new user with level 15 privileges and a secret password. I go to login via webbrowser and I put in my credentials, but I get rejected. I have tested the username and password via the CLI, and it works fine, I just cant seam to login to Cisco CP.