Cisco Wireless :: 877w Communication Between Wi-Fi Clients
Apr 12, 2012
I have a Cisco 877w (configuration shown below) and i am trying to use a Photo Transfer App on my iPhone4s and iPad3 which allows transfer of photos and videos between the devices using WiFi, the only thing is i cannot get my devices to communicate with each other and i suspect that this is to do with the configuration of my router as the app works perfectly using bluetooth but obviously a lot slower. I cannot even ping the devices from my pc which is also on the same WiFi network. How i should tweak my config?
View 2 Replies
ADVERTISEMENT
Jul 6, 2012
I have a Cisco 877W router that has been running flawlessly for nearly 2 years. During that time I've never had to manually reset the router, it has been more reliable than my ISP.However one month ago I left my business for a week and came back to find that the WLAN was no longer visible from my laptop. I searched google, tech forums, and these forums for conclusive explanations as to what is happening but found nothing.The main issue is an inability to see the network, old wireless devices that have been using the WLAN for a while have no trouble viewing the network or connecting to it.How ever, any time a new device is brought in (Samsung Galaxy Tab, new Laptops, and new Desktops) the WLAN is not available.I was able to make the device visible to my laptop by changing the country code on my network device to Region 1, but this is not an option for all devices or configurations.
I have changed the broadcast channels, shutting down the WLAN, configuring WLAN differently (through several different Security methods).My separate access points are usually visible by all clients, (I use D-LINK wifi routers configured to AP mode throughout my facility) however the Cisco just doesn't like to be seen?
View 12 Replies
View Related
Feb 1, 2011
I have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies
View Related
Jan 3, 2010
I have a small CCENT/CCNA lab with a few switches and routers which I would like to connect to my D-link home router so that it can access the outside world. I have an 877W which I believe is supposed to be able to connect to a wifi network as a client.
I have seen reference to configuring a bridge but this is something outside of my current understanding. The idea is to have the 877W with it's wireless interface connected to my wireless network and the Lab connected to the 877's intergrated switch, using the 877 as a basic router connecting the two networks. I've scoured Google and put together a configuration using what I could find in forum posts and Cisco documentation. The D-link is set up for auto WPA/WPA2 Personal (TKIP or AES). I'm using an ASCII key with an update interval of 0. I've never had a problem with other devices trying to connecting to it.
At the moment the 877W seems to connect to the D-link but then lose it's association, from what I can see it looks like the 877 is trying to rotate the key? Once this happens my laptop loses it's wireless connection and I need to reboot the D-link to get it back. Interestingly the Windows 7 network icon shows three computers with a link between each as the network icon when this happens. It's as if the 877W acts as a Rogue access point and steals my client's connection. On one attempt the debug output showed the 877 geting an IP address from the D-link's DHCP so it does seem to connect initially.
Config and debug output are below.
Config:
!dot11 ssid MYSSIDauthentication openauthentication key-management wpainfrastructure-ssidwpa-psk ascii 7 MYWPAKEY
!interface Dot11Radio0ip address dhcpshutdown!encryption mode ciphers aes-ccm
[Code].....
View 2 Replies
View Related
Oct 11, 2012
Ive been struggling with this issue for a week now with an 877w (now with andvanced ip ios) in short my wireless network consists of
The internal dot11 sibinterface 0.11 radio (IP Address 10.0.1.1) which on bridge group 1 (IP Address 10.0.0.10) The SSID for the radio is on vlan 11 which has no ip address.
This works i can ping the internal network and internet
The guest dot11 sibinterface 0.10 radio (IP Address 10.0.3.1) which on bridge group 2 (IP Address 10.0.2.1) The SSID for the radio is on vlan 10 which has no ip address.
This dosnt work i get no no recived packets on the clients network stats and i cant ping any name servers or the radio ip address.The client is listed as being successfully accosated with the show dot11 assoc commmand
Ive tried taking the guest wireless and creating a new vlan for it (so its not on the same vlan as the tmg firewall interface) so that i have only the dot11 radio and vlan 12 on brige group 2 but the same thing happens no traffic on the guest vlan.
Ive turned off all authentication while testing this and the wireless network is currently in open mode until its fixed ive also only configured whats neccessry to test the wireless connectivity (no radius etc) that will be added later, Im also not using dhcp yet and the client is configured to the apporprite adderess staticly ie 10.0.1.1 10.0.3.2 its not a dhcp issue
!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot-end-marker!logging message-counter syslog!aaa
[Code].....
View 4 Replies
View Related
Nov 25, 2011
We have dlink dir320 router and cisco 877W.
The goal is to make a 877W to work as a wireless client of dlink dir320 and brigde the LAN&WLAN so than the LAN clients of 877W could take DHCP from Dlink 320 directly.
Here's the config of 877w:
!
bridge irb
!
dot11 ssid DLINK_SSID
[Code].....
View 1 Replies
View Related
Jun 11, 2011
My router keeps on disconnecting?
View 1 Replies
View Related
Jan 17, 2013
This problem only seems to affect one of our sites. Every once in a while, several APs would lose link to the 5508 and get stranded. The only way to fix the issue is either to power cycle, or better yet SSH into the APs and use the command "capwap ap controller ip address x.x.x.x", and then they'd automatically rejoin the controller. At first, I thought network hiccups caused the APs to lose connectivity, but there's none that I could find. I have the primary/secondary controller IPs configured in them as well. See log below:
[previous log entries show AP working as intended, then...]
*Jan 18 05:29:29.632: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(CAPWAP_ECHO_REQUEST
., 1)
*Jan 18 05:29:29.632: %LWAPP-3-CLIENTEVENTLOG: Switching to Standalone mode
*Jan 18 05:29:29.645: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Jan 18 05:29:29.645: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to [ommitted due to security reason]:5246
*Jan 18 05:29:29.704: %WIDS-6-DISABLED: IDS Signature is removed and disabled.
[code]....
View 2 Replies
View Related
May 23, 2013
I am new to configuring WLC's. Our small business (5-15 wireless devices + 15ish wired) is trying to use a hand-me-down WLC and AP for our office wifi. We have a WLC 2106 directly connected to a 1231G-A-K9 via the WLC's port 8 POE. I am aware Cisco does not recommend this method, but we do not have a configurable switch at our disposal. We do not need separate VLAN's therefore I have left everything untagged. The AP has a static IP setup to allow communication to the WLC since it did not pull one from the WLC.
The AP is getting the correct network information and is showing up on the WLC monitoring page. I am able to connect to the new wireless network and able to ping between devices connected to the same AP. Now here is my question/issue. I cannot get communication from the WLC/AP to the rest of our network via an unconfigurable Netgear switch (FS605v3). After connecting an open switch port from the Netgear switch to port 4 on the WLC, I am lost. I tried giving port 4 on the WLC an address on the office network, but I receive an error stating "the IP information conflicts with another device".
Here is what I have setup on WLC
Virtual - 1.1.1.1
MNG IP-192.168.10.10
AP MNG Ip- 192.168.10.11
Subnet - /24
Gateway - 192.168.10.1
DHCP - 192.168.10.250
DNS - 192.168.10.250
Static Address on the AP's fa0-192.168.10.15
Attempted port 4 setup on WLC
VLAN identifier 0
IP- 192.168.10.25
Mask - /24
Gateway - 192.168.10.1
Port - 4
Our office network setup:
Subnet - /24
Gateway-192.168.10.1
DHCP - 192.168.10.250
DNS - 192.168.10.250
View 1 Replies
View Related
Mar 31, 2012
i have a client company that needs to extend their network. i am advising them to purchase the cisco aironet 1550. does the wireless AP support all the communication that is generated by SAP business one? Also, if this AP is placed outside on a over their offices, what is the estimate range that it will cover knowing that their offices are only one story high but do have a big shed that contains some production machine and metals everywhere
View 1 Replies
View Related
Jun 18, 2012
I have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
Result of the command: "show running-config"
: Saved
:
ASA Version 7.2(4)
!
hostname ASA
domain-name default.domain.invalid
[code].....
what I need to add to get the vpn client to be able to ping the router and clients?
View 3 Replies
View Related
Nov 5, 2012
We currently have an ASA 5520 communicating with 10 ASA 5510's, all on static outside addresses. I was asked to add 5 additional 5510's on dynamic address. All worked well in testing until it was decided that some of the dynamic clients needed to talk to each other.
My testing shows packets just dying in the 5520.
View 1 Replies
View Related
Jun 8, 2011
Wireless communication is dissabled. Please turn on the wireless communication switch. meanwhile it tells me my hardware radio is turned off
View 1 Replies
View Related
Jun 6, 2012
my question regards to a pair of WLC 4402 with 7.0.98.0 software.Actual, our security policy does not really allow any peer-to-peer communication in a wireless LAN. Therefore we set the 'P2P Blocking Action' to drop, and the 'Broadcast Forwarding' feature to disabled (default).But now there is a special requirement for two mobile endpoints to communicate with each other, because one device controls the other.To test the communication, we first disabled P2P Blocking (without success) and further enabled Broadcast Forwarding to bring the communication up. Now it works, but the configuration disagrees with our policy.
1. Is there an alternative configuration as described possible, so that we do not violate the security policy? To allow only p2p connection between the two devices, ist should also be possible to drop any else by an ACL. But how to fix the problem with the broadcast, because of the needed ARP? My idea was to use a static ARP entry, but as far as i know, one of the both devices is not able for it.
2. Because, I did not find any detailed documentation:
2a. with enabled Broadcast Forwarding, the controller forwards all broadcast for any configured SSID, right?
2b. is the broadcast limited to the source VLAN/SSID?
2c. is the broadcast limited to an AP, to an WLC, or is it broadcasted to every AP on every WLC that has the relevant SSID?
we already have two new 5508 but not in an operational state now, because we plan to implement new 3600 APs.Do these WLCs offer more/another circumstances or possibilities?
View 1 Replies
View Related
Jun 16, 2011
Configuring QoS on my cisco877W for VoIP below is the current config. [code]
View 3 Replies
View Related
May 15, 2013
how to setup the wireless interface to forward multicast packets? Basically I cant get the ipads etc.. to see the AppleTV to control it. I connected an AP and it works fine so its got to be something with the way the router handles the packets from teh integrated wireless interface. I've been searching the forum for about 1hr and haven't founf anything other than a breif mention of broadcast forwarding and multicast setup.
View 1 Replies
View Related
May 14, 2012
All of a sudden I started experiencing occasional loss of communication with my router. I tried updating the firmware to the latest (1.0.04) but am still experiencing the same thing.I don't lose internet access, I lose connection to the router itself. If I power cycle the router, the connection is re-established and I'm able to access the router and in turn the internet. I'm seeing this on both wired and wireless connections. Last night the Cisco logo actually turned off when I lost connection (this was a first). When I power cycled, connection was restored and the logo lit up again.
View 3 Replies
View Related
Jul 6, 2012
I have a Netgear WNDR4500 running the stock firmware, acting as a router for my home. I also have 2 routers that are flashed with DD-WRT (Linksys WRT54G and Asus WL-520GU) running as client bridges. The Netgear is 192.168.1.1 and the other 2 client bridges are 192.168.1.2 and 192.168.10.3. The Netgear router is performing DHCP giving addresses from 192.168.10.100 to 192.168.10.254. I have numerous machines connected to the Netgear, wirelessly and wired, and numerous machines wired to each client bridge. All machines have IP addresses that are 192.168.10.100, 192.168.10.101, 192.168.10.102, etc... Everything is working fine, but I have one question: When I access the Netgear router, it shows the client bridges as clients, machines that are wired and wireless to the Netgear router are listed as clients, but the client list does not show any clients that are connected to the client bridges. I assumed that since the router is performing DHCP that all clients would show up.
View 2 Replies
View Related
Dec 16, 2011
Cisco 877W. I configured it for PPPoE. But once I plug in the ADSL line, the dialer interface will get IP Address. But after like 2 minutes the PPP link will go off and I will get this log message: "Interface Vi1 unbound from profile Di1".
View 2 Replies
View Related
Jan 24, 2012
I am using a company called Zen for adsl, I have 8 IP from XXX.XXX.XXX.248 to - XXX.XXX.XXX.255, Gateway is 254, Address 249-250-251-252-253 I would like to appear at the 4 sockets at back of router, and 252,253 will be used for a server...I understand I should be using Routed IP , but I cannot get it to work, I can ping out to google from the server, but the server is not live to the world. [code]
View 8 Replies
View Related
Nov 7, 2011
I had the Cisco 877W Router working in my old company. The old company was closed and I bring all of network equirments to new company.I am trying to setup this router to new company but lost menu, console cable and software CD.
View 2 Replies
View Related
Jan 22, 2013
I have a Cisco 877W in place with an ADSL connection, which is working fine. However I cannot get it to hand out a DHCP address. If I associate with the AP over wireless then set a static IP I have full connectivity, similarly if I connect over Eth0 and set a static IP I have full connectivity. So it does just seem to be DHCP. Below shows my config... Any thoughts on the issue? Is it access-list related?I have checked with Wireshark and I see the DHCP request being sent out, but I don't see a DHCP offer being returned
View 4 Replies
View Related
Feb 26, 2007
how to configure WPA2 /AES on 877W. Also how to enable IPS on the router. My ios is 12.4.11T1
View 7 Replies
View Related
Sep 9, 2011
I am running an 877W in the home that for the most part works fine, however after being connected for a variable amount of time I partially loose my DSL connection. Line sync stays up, but the traffic is lost.
A shut/no sut of the atm or dialer interfaces does not resolve the issue, only a reload or power down/up will fix the prob short term till it happens again.
Am currently running advipservicesk9-mz.151-3.T1, but have also rolled back to advipservicesk9-mz.124-24.T5 which has the same issue. Have tried a 857W with the same results. So ruling out IOS and hardware, its pointing to a config issue. It has also only been an issue since changing from ADSL1 to ADSL2+.
interface ATM0
no ip address
no shutdown
no atm ilmi-keepalive
exit
[code]....
I've tries some changes mentioned here and from other sites, but no success yet...
View 14 Replies
View Related
Dec 20, 2011
I have a working easyvpn setup. We need to change the HQ ip address (current it is i.e 85.146.110.101). This is ACL is applied to Fastethenet conecting to ISP:
interface FastEthernet4
description $FW_OUTSIDE$$ETH-WAN$
ip address dhcp
ip access-group 101 in
ip inspect SDM_LOW out
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto ipsec client ezvpn Acom
As soon as I apply again the ACL to interface Fastethernet 4, access to internet is lost. If I put original ACL 101 (with ip address 85.146.110.101) it works fine.
So I am wodering what wrong with may ACL? Should I make the change via SDM not CLI (to be honest I did not know/use SDM before today)?
View 3 Replies
View Related
Feb 21, 2013
I've an 877W with four V LANS, All bridged (group) onto a BVI which is bonded to ATM etc for ADSL:
c870-advipservicesk9-mz.124-15.T5.bin"
1 is the backbone, and for the switch, and has DHCP running and working with no problems - x.y.1.z . Multicast is enabled so that various multimedia bits of kit can find each other.
2 is the "primary" WiFi, which has android devices as they cannot handle SSID not being broadcast or devices that can only do wep.(WiFi radio) it has DHCP, x.y.2.z which works fine. Multicast is enabled so that various multimedia bits of kit can find each other.
3 is a secondary WiFi for the kids, "hidden" ssid. They are fire walled so that bugs can't infect any other windows PC DHCP x.y.3.z.
4 Is a secondary WiFi for our laptops, "hidden" ssid .
For some reason, DHCP is not working on 4. it was working until the good lady of the house quizzed why her net was not working... I've concentrated on vlan4, as there are no "local" access-lists definitions to stop anything. I've enabled debug ip dhcp server, and can see requests serviced on Vlan2, but not on 4, I've enabled/re enabled encryption/ shields on Vlan4, but still can't see dhcp requests arriving and do not see them being stopped somewhere. I can see that the station authenticates OK, but if I connect the same laptop to v lan 02, requests pour in and are answered, proving it's maybe not a Microsoft problem.
Let me just say, I'm more or less self taught with the the net, no real mentoring, so 'think' I have the general idea of the different layers, access-lists etc. so this config is probably not ideal, but it works.
version 12.4
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
[code]....
View 5 Replies
View Related
Oct 9, 2010
I'm about to return my E3000 because I can't figure this problem out. As you know a new Apple TV was released and along with it you now have the capability to send music and photos from iTunes on your laptop to your Apple TV which you can then play on your TV. These two components communicate through your wireless router. However this is not happening because (I believe) that the E3000 is blocking something (a port, some rouge firewall setting, etc.). I would be happy opening every frigging port this thing has and blocking all it's internal firewalls just to see if I can get these two devices working correctly. The software that allows this to all occur is called Airplay via your homeshare g network. Any success in getting your Apple TV and your iTunes and perhaps your iPhone to call communicate together or how the E3000 works.
View 9 Replies
View Related
Nov 18, 2012
While i was looking around in my stuff in the office i have found a Cisco 877W ADSL router .. so i have decided to use it instead of the one i am using now which is provided by the ISP that's made by Huawei.Anyway i have a good knowledge about basic cisco router configuration but i had never configured ADSL Cisco router, so i looked around on Cisco website, and i was lucky to get this two linksCisco DSL Router Configuration and Troubleshooting Guide - Step-by-Step Configuration of PPPoA with a Dynamic IP Address - Cisco Systems[CODE]
View 7 Replies
View Related
Apr 26, 2012
Looking to setup a backup router for our disaster recovery plan. We currently have a Cisco 877W that was setup by our ISP. I can log into the device with Telnet and a console cable, but I am not good using IOS commands, so I would like to use CCA. Unfortunatley, I cannot access the router using the software. I assume something is disabled in the config. Like HTTP or something.
View 1 Replies
View Related
Jan 6, 2011
A client of mine is using a Cisco 877w wireless router, they have one IP phone connected to one of the RJ45 ports on the back of the router and their main desktop is also plugged directly into the router - this all functions perfectly.However, the router is in a private house and as such it provides connectivity for all other wireless devices such as iPhones, Ipads and Xbox Live etc. The problem is that the router only allows 5 devices to be connected at any one time and when a sixth attempts to connect to the router the first device (the IP phone) is diconnected automatically.
So my client can be using the IP phone for an important call and his son walks in with Iphone and Xbox, friends etc etc and the IP phone is immediatley disonnected from the router. I beleive that the router should allow more than 5 devices to connect and would hope there is a way of stopping the IP phone constantly being disconnected.I have already paid for "Cisco Engineers" to attend this site but they cannot get it working.
View 4 Replies
View Related
Nov 23, 2011
I would like to configure an 877w I just bought. It's connecting to a UK ADSL2+ link.I'm a penetration tester and I want to put the Cisco router in front of my existing firewall which has an IPS on it, so that it doesn't get in the way of port scans and vulnerability scans. My ISP has issued me with 14 usable addresses a/240 subnet and basically I want to be able to use the route with just the public IP addresses. I have configured Cisco routers before, but never with this type of configuration. It's always been single public IP address NAT'd through to one or two internal LAN's.
It will be nice if I could assign the wireless and fast ethernet ports to the same VLAN using the public addresses. I don't want to use DHCP I'm quite happy statically assigning IP addresses to the computers wireless and LAN interfaces. I am reasonably certain this is possible because not sure how to do it and a little busy at the moment carrying out penetration tests.
View 7 Replies
View Related
Nov 7, 2011
I'm having a business DSL-connection which requires a modem from the provider (It cannot be replaced by another modem/router)I want to know if it is possible to place the Cisco 877W-G-E-K9 behind the modem and set it up as an VPN-server.The internet connection wil be established in the modem/router of our provider.
View 20 Replies
View Related
Mar 15, 2012
I just bought myself a Cisco 877W in hope that I could touch up on my IOS skills. The configuration went well, however I have found that after configuring the Dot11Radio0 interface, the ADSL2+ has slowed down dramatically. I am still syncing at a decent speed (decent enough for how far I live from the exchange), but web browsing and other internet traffic is horrible. Originally, I was downloading at ~500kb/s, but now I can't even navigate to a website to perform testing. :
I have another ADSL2+ modem which works just fine (using it right now to write this post)
I originally thought this may have been a DNS issue. However, performing an nslookup on various sites from both the router itself and a client PC shows that resolution occurs in only a few seconds. With that said, there are some sites which will load in an instant (Google.com, for example) while others will simply refuse to load. DNS server (Server 2k8) is on the LAN with forwarders to ISP DNS addresses.
View 1 Replies
View Related
