I am facing a problem with my access point AIR-LAP1141N-E-K9, which was converted from LWAPP to autonomous, radio Interface Dot11Radio0 is going to reset down state very frequently.AP is connected to WS-C3560G-24PS (POE) switch. [code]
View 4 RepliesI have a problem with one of our 1131AG AP, B/G radio go down:
show controller dot11Radio 0:
(...)
Last radio reset code: 46
Radio resets - total:2946 retries:0 failed:0
Reset Stats: Start Cnt: 2742, Recovery: Cnt 33, Last Ret: 20, Fails: 0, Recvry Status: Stalled NO, In Prog NO
Code/Count: 37/00025 46/02851 51/00005 54/00030
Code/Count: 62/00001 67/00001 71/00033
Although I was not able to find any information about this reset code in Cisco documents. What is the reset code 46?What can i do?
I am wondering if anyone has seen this before. We have about 50 AIR-LAP1242AG-E-K9 access points connected to a WLC5508 running 7.4.100.0. These were all being used as autonomous APs previously and were converted when the controller was installed. About 12 of these have a lovely feature where their radio interface goes down at random. The radio is still in enable mode but the opertational status is DOWN. It seems to happen particularly when there has been a power outage and the AP rejoins the controller. All of the other 1242s are fine and never sees this problem. The APs are all on power injectors.
Once the radio is down, the only way I can get the to come back online is by doing the following:
1. Set the radio admin status to "disable" and apply
2. Turn off CDP
3. Reboot the AP Wait until the AP is back online and registered on the controller
4. Enable the radio admin status and CDP.
If I do not remove the CDP setting I cannot bring the radio back to "UP". I know we had previous issues with autonomous 1242 APs that did not like CDP being enabled. Have I perhaps got a bunch that are like that? Despite these having operated as autonomous APs they are AIR-LAP1242 from the factory.
I have a couple of 114n APs in my network and the CAPWAP uptime and AP uptime are almost the same. But there is one which always resets after some time. I have moved across to another switch port but the issue persists. I have other 1141 and 1131's on this switch and no problems. The keep alives between the AP and Controller is regular. I can't get more info from the traps as the reason code is always;
" AP associated to Controller is UP. Reason: Radio interface reset due to Init"
"AP associated to Controller is down. Reason: Radio interface reset"
"AP associated to Controller is UP. Reason: Radio interface reset"
####Only 2ice was the reason code "Operator changed 11g mode". I have seen some posts about similar problems but there hasn't been any concrete solution provided.
note that RLDP is disabled, Primary discovery timer is 120sec, and the version is 7.098
We are facing an issue with a customer where a Cisco 4400 Series controller is blocking the 802.11a/n Radio Interface of a 1250 AP. The radio shows as down on the controller GUI. The error message on the GUI is that the 'Regulatory Domain' is not supported. This can be seen from the attached screenshot. Also relevant parts of the WLC configs are attached. WLC: Cisco 4402 WirelessWLC Country: SADevice: Cisco Lightweight Access Point 1250 (LAP) is controlled through the 4402 Cisco Wireless LAN Controller (WLC)The operating system version of the LAP: c1250-k9w8-mx.124-18a.JA version of the WLC: Software Version 5.2.178.0 The problem is that the controller shows that the 802.11a/n Radio Interface in Radio Slot # 1 is always down , the customer tried to manually 'no shut' the AP interface from the console and it worked , but obviously this solution would not work as the configuration cannot be saved (LW AP).
View 12 Replies View RelatedIs it problem with iPads or LAP1141n?WLC 4404 and many 1142 and 1141, so other devices laptops, iphones, androind phone works as well.But iPad authorized, but can't get an ip address from dhcp server (dhcp not local on wlc, on windows machine) with coverage lap1141, but it get ip with coverage lap1142, and when i got it i roaming to lap1141 and it stays, if i off/on iPads can't get it again from lap1141.
View 14 Replies View RelatedI converted a Cisco Aironet 1142 Lightweight access point to Autonomous and at first it works properly but every some days the dot11Radio0 interface is down (similar case than the cisco support community case "Autonomous 1142 AP shuts down 2.4 radio interface" The 802.11g radio shows as “Dot11Radio0 is reset, line protocol is down” while the 802.11a radio appears to be up and running, I have to reload the device so that the Dot11Radio0 is up again.
View 1 Replies View RelatedI converted a Cisco Aironet 1142 Lightweight access point to Autonomous and at first it works properly but every some days the dot11Radio0 interface is down (similar case than the cisco support community case "Autonomous 1142 AP shuts down 2.4 radio interface"
The 802.11g radio shows as “Dot11Radio0 is reset, line protocol is down” while the 802.11a radio appears to be up and running,
I have to reload the device so that the Dot11Radio0 is up again,
We have two autonomous access point 1142 series running 12.4(21a)JA1 and randomly the Dot11Radio0 interface goes into reset/down state. At first I thought it was something related to power consumption issue on the switch, but looking at the remaining (w) I have plenty.
View 8 Replies View RelatedWe have 4x AP1142 standalone APs in WDS mode with roaming and RADIUS from Windows AD for auth.Everything works as expected apart from two APs that frequently reset Dot11Radio0 interface. The other two are fine.
The config on all APs is identical, version of IOS is the same accross all APs (12.4(23c)JA3). The only way to get reset inteface back up is to "reload". [code]
This is regarding an issue with one of my access point. The access point 1252 is autonomous one running the IOS version C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
The status of the dot11Radio 0 interface is showing as RESET. I have pasted the interface brief details below.
ap03#
ap03#
ap03#sh ip int brief
[Code].....
Info Of a EEM configuration that would reset an interface on the router and force a re-dhcp when connectivity is lost to an upstream router? I would like the applet to run every 15 minutes. I am thinking of an event that is triggered to do a shut/no shut on the interface when 5 pings are lost.
View 5 Replies View RelatedWe have a Cisco 886G router connected to the internet. The router receives an ip address. We experience however a problem when the lease time expires. The router does not send a DHCP request to renew it's ip address in time. This causes an interface reset, and connectivity loss, after the lease time of 8 hours.
We are running IOS 880data-universalk9-mz.151-3.T.bin. Config on DHCP receiving interface is:
interface VlanX description To Internet MODEM ip address dhcp ip access-group TEST in!
I would like to know if I can reset the TTL value for all IP packets to 64 as they exit my network through an ASA5505 to the outside network. Can this be done on a 5505?
View 1 Replies View RelatedI started having connectivity issues between my core 4506E (Sup7E) and Cisco 2960S. There were input and CRC errors on Te int (SFP 10Gb - LRM) on 2960S, which cause the interface to reset and drop connections. While troubleshooting this issue, I have replaced patch cords and also had the tech checking the fiber. He said that there was some residue on one of the connectors, so the light levels fluctuated in 1300nm, but worked fine in 850. Well LRMs are using 1300, so he re-polished the tips, which worked to stabilize the light levels. After all that, I was still receiving the input/CRC errors, but the connection was NOT dropping. As my last resort I swapped the SFPs between the core and 2960, thinking I should start having issues on the core end. Well, here's what happened: I stopped receiving input/CRC errors on 2960 (also no errors on the core), but 2960s started generating Rx power high alarms: [code]
View 1 Replies View RelatedI have an issue with input errors, overruns, and input reset drops on the inside interface of an 5580-40 (v8.2.5: Transparent mode) The box is not stressed at all according to the 'show' commands in the Cisco troubleshooting performance document for PIX/ASA v8.2.5. Nothing stands out because is pretty much normal, nothing (processes, RAM, blocks, IO...) really being highly utilized. I have replaced the 10Gig card and that seemed to work because the rate of errors has gone down tremedously. The next step is to RMA the whole box.My question is what would be the cause of the inside interface to stop processing traffic (I say that because the syslog server stops receiving messages) for some periods of 30 seconds periodically throughout the day and clients lose their connections (ie Outlook, IBM Sametime, Oracle, MSSQL..etc). Can the issue be somewhere related to the overruns and input errors?
View 2 Replies View RelatedI've recently installed a Cisco 2504 WLAN Controller with (5) AIR-LAP1042N-A-K9 Access Points. Everything is working fine as far as the APs connecting to the controller, and clients being able to connect to the WiFi and get network access, etc. The one problem I have is that one AP's b/g/n radio is not active.
If I go to the WLAN Controller management web page, and look at the Access Point Summary, it shows that I have five (5) 802.11 a/n radios active but only four (4) 802.11 b/g/n radios active. I know which AP is affected and clients can indeed connect to that radio using wireless 'B' but not 'N'.I have only one WLAN configured on the 2504 (WLAN ID 1), and one AP group name (default-group) so there are no special groupings of APs. I have been through every page of the Controller management page with a "fine tooth comb" and cannot find any place where I could accidentally be turning off the a/n radio for a single controller.
The network consists of 133 RAPs/MAPs/1131 APs and all joined the WLC. When I check the 802.11 a/n radio tab, I see only 129 APs and the 802.11 b/g/n tab I see 133 APs. I found out that 4 LAP1131 is not showing in the 802.11 a/n tab. I tried resetting the AP thru the WLC and still the don't see it in the 802.11 a/n tab.
View 7 Replies View RelatedI've a 2106 WLC and the software is upgrade to 7.0.220.0. There are 3 APs with external power adapter work normally on it. Here is the problem: There is another AP with external power adapter has join the the WLC successfully. But it can not enable the radio 802.11b. Following is the error message on CLI
(Cisco Controller) config>802.11b enable AP001d.a1ef.b5f4 Cisco AP has not enough in-line power to enable radio
how to disable radio on the AP 1140 from NCS script .
View 5 Replies View RelatedI've just bought an access point AP1141N for my small business but unfortunately there is only Radio 0- 2.4G available through web interface. It is working fine but I would like to have access to radio 1 (5Ghz) as well.
View 2 Replies View Related We have two different entities we support and both are set up as autonomouse wireless groups. The SSID is the same though so they can use their 7921's between floors and buildings. The problem we have had is that the phones on the first floor were getting the IP's of the organization on the second floor. When you view the AP's on the phone the ap directly next to it on the first floor (the one its suppose to talk to) is listed first, The strange thing is that shows it is connected to the right AP (the first floor one). The AP on the second floor is also listed but its about third down. After the phone sits it will actually change IP's but not all of them. Their were a few phones that took about a half a day to get the correct IP.
My question is how do these phones grab their ip's? I know how DHCP works but I am needing to know specifically how the radio works on the 7921's. What is the boot up process? It appears that it must cycle through each channel starting with the highest and loop through a process in descending order: compare ssid's and then authenticate if possible. I am assuming it is seeing the second floor first because initially they all get the second floor ip. The second floor is on channel 60 and the one it should connect to is on channel 36 (We are using 802.11a). That's how I came up with my descending channel theory.
I have a westell DSL modem/router supplied by Frontier. It connects only to the telephone line and via cat5 to my main router, a cisco EA6500. Everything seems to be working fine, I just would like to understand a few things.I disabled wireless radio on the westell, enabled it on the cisco, so I have just one WIFI network active.I know I am not supposed to have two DHCP servers active, but I did not know how else to be sure the CISCO would get a good address, so I left DHCP active on the WESTELL, and also enabled it on the CISCO to provide service for the rest of the net.The WESTELL admin interface is at 192.168.1.1, and assigns addresses in this range.According to the WESTELL, the CISCO is at 192.168.1.27, which I assume was assigned by DHCP.The CISCO has an admin interface at 10.144.224.224, and assigns addresses in this range to all the other devices on my net.As I say, everything works.I can access both router admin pages with a browser on my main 10.144.224 network, and can ping both.But I don't understand why it works.What rules allow me to talk to the WESTELL admin page from the CISCO private network, but do NOT propagate the DHCP access which is at the exact same IP address.
It is great that it works. But should I really have disabled DHCP on the WESTELL and assigned a static address to the CISCO? Or is this situation actually provided for in the rules, not just a lucky accident that it works?Why does the scanner say that the CISCO DHCP is "Unknown" rather than Authorized or Unauthorized? Is there something I can or should do to get it to be "Authorized"? I can ping 192.168.1.1, but not the 192.168.1.27 (times out), and yet when I ping a non-existent 192.169.1.3 I get "Reply from 192.168.1.27: Destination host unreachable".
I can't find out how to turn on my wireless radio on IBM T41p. The Fn+F5 does nothing. I do not have internet because of this.
View 2 Replies View RelatedIm using WLC 2504 with vertion 7.4 and 2600 LAP's the access points are working fine when its isolated from the live network, but once its in the live network the AP radios resetting (APs won't reboot) and unregistering from the WLC in random intervals,
WLC error log is as follow,
---------------Show msglog---------------
Message Log Severity Level ...................... ERROR
*emWeb: Apr 05 14:57:02.966: #APF-0-SITE_OVERRIDE_CONFIG_RESET: apf_site_override.c:400 Resetting site override config.
*Dot1x_NW_MsgTask_6: Apr 05 14:50:14.444: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 20:10:7a:1a:60:9e - got 00 00 00 00 00 00 00 00, expected 00 00 00 00 00 00 00 02
[code].....
I connected AP 1522 to AC power source and this is the message that i received on the console port.
%CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (0000.0000.0000)
Why this message apear ?This is not sufficient power to bring up radio interfaces?
I am building a BOM for a customer and I need to present cheaper options than 3500 or 3600 APs. I thought of these two models but I don't know what models of antennas to pick.1602 is a 3X3 MIMO with 3 antenna connectors. How many 2.4 GHz and how many 5.8 GHz antennas should I pick for each radio?2602 is a 3X4 MIMO with 4 antenna connectors. In this case I suppose there are 2 connectors per radio.
View 9 Replies View RelatedWe have 6 1262 APs and a 2504 WLC. 5 of the 1262 appear correctly with 2 radios. One of them shows 1 radio. See screen shots below showing model numbers and interfaces on the AP with one radio available (All other 1262s show 2 radios as normal). Tried resetting the AP to factory default, but same result. Do I have a defective AP?
View 3 Replies View RelatedI have a 2504 WLC with two 1522 AP's one is Root the other Mesh the 802.11b/g/n/ Admin Status says Up but the Operational Status says down. How can I turn this on? When I change the Admin status to enable I get a "Error in Enabling Admin Status"
View 7 Replies View RelatedWhen I view web page of 1410 radio is show ethernet enabled and up but radio as disabled and down. I have tried to enable but to no avail. Is this a sign my radio has gone bad?
View 3 Replies View RelatedI have cisco LWAPP 1242 AP already joined controller but 802.11b/g shows down on the radio 0 interface. I tried to enable it but it comes with an error" Error in enabling admin status". I have resetted the AP to factory default settings and even replaced with NEW AP.
View 3 Replies View RelatedI am running the upgrade tool on Aironet AP1230B-A-K9. I can't join the controller by using the upgrade tool. the error is "AP does not have Supported Radio". What radio is the upgrade tool or controller look for on Aironet 1200 series? This AP is running 802.11b. However, I have several APs which the same model is running on the same one controller. The controller is model 4402.
View 8 Replies View RelatedRunning vwlc 7.3.101 and encountered a smaller issue.When you enable / disable a SSID, all AP's reset their radio interfaces... causing everyone to drop their connection.
View 4 Replies View Related