Cisco Wireless :: Configuring Autonomous 1141 To Do DHCP For Guest Wi-Fi?
Oct 6, 2012
I have an existing setup consisting of:
Windows Server - doing DHCP for private wired/wireless
Cisco 1141 Autonomous WAP with only private wireless access.
ASA 5505 (with very basic licensing)
HP switch
The customer wants to have guest WiFi.
The guest WiFi is going out to the internet via a seperate VLAN/interface on the ASA. Can the 1141 do DHCP for the guest WiFi? Or do I need to do it via the ASA?
View 1 Replies
ADVERTISEMENT
Jul 7, 2011
I have a customer who accedentally got a AIR-LAP-1141. He needs it to be autonomous. If I convert from LWAP to Autonomous, will there be a licensing issue?
View 1 Replies
View Related
Dec 17, 2012
recently we purchased cisco aironet AIR-AP1141N-E-K9 standalone model. after configuring it , client has no problem with connection and coverage, but there is problem with thoughput. clients are not able to connect at higher rates, even if i set channel width at 40 mhz, max rate for N capable client device is 54mb.
[URL]
View 20 Replies
View Related
Aug 17, 2011
I'm setting up a Cisco Aironet 1141 (standalone mode, AP) to handle wireless traffic in the office. It gives out 2 mbssids, one of which authenticates domain users through a RADIUS server and places them in an appropriate VLAN (RADIUS options 64, 65, and 81). The other is a guest ssid that uses WPA-PSK and places users in the restricted guest VLAN. Physically, the AP is connected to a 3750 PoE Catalyst, to which RADIUS and DHCP servers are also connected. AP, SSIDs, RADIUS and EAP authentication all work. The configuration given below is a working configuration. People do get authenticated and do get placed in the appropriate vlan. The problem is that, once authenticated, the "Obtaining IP Address" phase on the client hangs and most clients timeout without getting an IP address. Given that the DHCP server is on the same switch and a test simple ASUS Wi-Fi IP gives out the same scenario (except the multiple VLAN) at the speed of light, I don't think that it's a problem with the network connections between clients and the DHCP server. After reading some topics here, I realized that probably other communication will be extremely slow, as well, but haven't tested that for sure. Clients are all non-Cisco - smartphones, notebooks, etc. Most of them are 802.11G, not N.
View 4 Replies
View Related
Nov 7, 2012
How do i get the 12.4 code to assign a dhcp address to my ethernet interface from my server? I deleted the default config on the 1141 and searching has not turned up anything useful.
View 1 Replies
View Related
Mar 5, 2012
good docs for configuring a 1260 autonomous AP?
View 1 Replies
View Related
May 5, 2011
I’m configuring a Cisco 1142n AP in autonomous mode. The networking part is successfully working, multiple VLANs, SSIDs etc. I would like to configure one of my wireless networks to work with WAP2-PSK and the other with WPA-PSK.I’m confused as to what encryption to set on each radio and the ciphers to use on the SSID for each vlan to enable the best possible security. I’m not using a RADIUS sever in my network .point me in the right direction with the right CLI commands?
View 12 Replies
View Related
Jul 11, 2012
Hardware: Cisco 3750 switch and Cisco autonomous access point (AIR-AP1142N-E-K9).Requirement: A single broadcast SSID; use dot1x to assign vlan 98 to authenticated clients (computer certificate); assign vlan 3 (guest) if the authentication fails.I can achieve assigning a guest vlan on authentication failure when using a wired connection by using the following command on the interface:authentication event fail action authorize vlan 3 I'm after a way to achieve the above using the wireless access point. The main point is that internal users cannot access vlan 3 as they have a valid certificate and that guests do not have to authenticate.
View 2 Replies
View Related
May 9, 2012
I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
View 10 Replies
View Related
Apr 3, 2012
I have 2 APs, Cisco Aironet 1040, and 2504 WLC.Is it possible to configure guest access (Guest SSID/VLAN and Corporative SSID/VLAN) without dedicated guest WLC in DMZ?
View 4 Replies
View Related
Jan 27, 2011
I have a AP541N connected to a UC560. We are currently configured for Wireless Voice and Data. We have added a Guest VLAN, but don't see where in CCA to secure the VLAN from accessing the other other two default VLANs.
Additional Info: AP541N-K9-1.7(2)UC560 15.0(1)XA2, RELEASE SOFTWARE (fc2)CCA 3.0
View 1 Replies
View Related
Aug 26, 2012
I have this guest wlan working with web authentication, as you may know in order to get authenticated you must have an IP address first then have a valid username and password. The problem is that if you don't have valid credentials you keep the IP address anyways.I'd like to know if there is a way to release the IPs that are not being used? The WLC is the DHCP server for this network.
-WLC4402
-6.0.202.0
View 6 Replies
View Related
Aug 6, 2012
This is rattling my brain. I have configured 2 SSIDs, one for internal, one for guests. They are on seperate VLANs (50 and 51) and bridge groups (1 and 2). I can get IPs via DHCP for the internal network, but not for the guest. I can't get DHCP for any VLAN 51 sub-interface, nor clients that connect to it. The overall goal is to keep all traffic on the guest network seperate from the internal traffic, however, DHCP requests will be from an internal server. I have removed all the access-lists for troubleshooting purposes. AP and Switchport configs are below!
AP Config
Current configuration : 4011 bytes
!
version 12.4
[Code].....
View 6 Replies
View Related
Jan 18, 2011
I have disabled the internal DHCP/DNS server in the routers firmware. I have enabled the wireless guest access SSID. A client associating with the Guest Wireless Access will obtain a DHCP address from the server in the LAN zone, but cannot resolve DNS as the firewall prevents traffic to flow from the Guest zone to the LAN zone, as it should.Is there a way to enable the DHCP server and DNS server in the routers firmware, but only on the Guest Zone? Is it possible to get the Guest Zone to have a different subnet?Tech support has hung up on me twice now.
View 5 Replies
View Related
Jan 28, 2012
I recently bought a Cisco SRP527W and I'm trying to setup a second wireless network for guests.
I created a "guest" VLAN and I assigned the "guest" SSID which I have created.
I created a "guest" DHCP server and assigned it to the "guest" VLAN.
The "guest" SSID is set to broadcast and has WPA2 Personal (TKIP+AES) authentication. These are exactly the same settings I have for the "non-guest" WiFi.
However, I can't get my clients to connect to the network. The "guest" WiFi is visible and clients are prompted to enter the password but after that they end up with an APIPA address. When I move the "guest" SSID to VLAN1 (along with all the other networks) then it works absolutely fine.
I was just wondering if I'm simply missing something in the configuration ..
The device is running the latest firmware (1.01.24 (003) September 7, 2011)
DHCP server has DNS Proxy setting enabled and WAN Interface configured as "Default Route" (have basically replicated the same settings as VLAN1)
View 1 Replies
View Related
Feb 24, 2013
I have a cisco wlan controller (2100) running software 7.0.235.0. I have the internal private wlan running off of port 1 and that is working fine with an internal dhcp server.Is it possible to setup another ssid (guest) and have the interface directly linked to a static ip on the WAN and also use the built in cisco internal dhcp server?
View 4 Replies
View Related
Feb 28, 2013
i have two 5508 ver 7.3.0, one is the primary and one is the guest controller. mobility is up and running. i have an exising guest ssid working with wpa2-psk and web authentication and its working fine but i require a second guest ssid that only uses a wpa2-psk for ipod/ipads as i cant use passive client on primary controller. i presently have the one vlan range and dhcp setup on the guest controller to give addressing to either ssid. i know you can have multiple ssid setup on the guest controller but in other sites i have only had one guest connection comming from the primary controller, just a primary controller on each sites was only creating one link to the same guest controler.
View 3 Replies
View Related
May 7, 2013
I have a problem with DHCP. I have two 2960 connected with a port channel on ports 47 and 48 as trunk with native vlan 10. I only have this one vlan. In port 1 of sw 1, I have a C800 as DHCP server.
I have an AP autonomous with single ssid on vlan 10. When I connect the AP to sw1, I receive dhcp with no problems.When I connect the AP to sw 2, I’m not getting IP by DHCP.I have DHCP snooping working on vlan 10 on both devices.
The ports where I connect the AP are access ports on vlan 10 config as trusted.The trunk ports are also configured as trusted.The port 1 of ws 1 that goes to the C800 is also configured as trusted.
figure out why I’m not getting IP by DHCP when I connect the AP to the SW 2.The only I notice is that when I connect the AP to sw 2, I get on SW 1 the message of packet drop by option 82, but even after configuring ip dhcp snooping information option allow-untrusted on both switches, the problem persists.
View 5 Replies
View Related
Feb 27, 2012
configuring DHCP on access point, i have cisco 1142N access point, in my network.. working in autonomous mode, i have assigned a static ip to access point with default gateway.. from AP i'm able to reach internet and user connecting to access point are not able to get ip.. i have DHCP server in my network. how to make access point to fetch ip from my dhcp server and assign the saem to client.
View 10 Replies
View Related
Feb 3, 2013
I just read that starting from version 7.4, the 2500 controller can be used to terminate guest anchor tunnels. have a question regarding the performance of the internal DHCP server when used in guest environments.
View 1 Replies
View Related
Feb 23, 2012
In our test set up, we have two WLC 5508 Controllers connected via Checkpoint UTM-1 firewall Inside and DMZ Interfaces. Both the WLC controllers are connected to the firewall via Cisco 3750 switch. On the Local (Inside) Controller, guest SSID is enabled and attached to the wireless management Interface. On the remote anchor controller, guest SSID is enabled and attached to the Management Interface as well. The following configs are replicated on both the Controllers.
SSID Name - guest
Interface - Management ( VLAN 10 on Local and VLAN 20 on remote) -
Mobility Group: Same configs at both ends
SSID Anchor : Anchor SSID on local and local SSID on Anchor.
AP: CAPWAP 3502 Management Subnet
[code]....
Is there any thing missing in the wireless configs and or the firewall rules as i could not see DHCP request back from the Anchor Controller. Also, after DHCP is obtained, the web authentication request will be redirected to an Amigopod device for authentication. In this case is the redirect URL congiguration to be performed only on the Anchor Controller or is this to be replicated on both the Local and Anchor Controllers.
View 8 Replies
View Related
Oct 30, 2012
with our WLC 5500 controller, once the clients get the DHCP address the page is not redirecting them to the guest portal.What is the best way to check as to why the redirection is failing.
View 8 Replies
View Related
Mar 15, 2012
My router a E4200. the thing is i want to disable the dhcp services from the router, because there are allready a dhcp server in my network. but if i disable the dhcp will the Guest wifi functions still work?
View 3 Replies
View Related
Jul 3, 2012
I've got an E4200v1 running 1.0.04 firmware with guest access enabled. I'd like to find out who is logged in using the guest access. Is there a way to get a list of the DHCP clients on the guest network? I'm able to do this for the non-guest access via the WEB interface's Status->Local Network->DHCP Clients Table page. But I can't find a similar table for the guest network.
View 3 Replies
View Related
Jan 26, 2013
I have a 2960 SI lan lite switch that I am configuring for admin and guest access. I have wireless AP's plugged into trunked ports 2 and 3. I am using two vlan's (in addition to the native VLAN). Vlan 5 for Admin and Vlan 10 for guest access. I have ACL configured on the router preventing guest users from accessing the Admin network. I want to prevent those on the guest network from seeing other hosts in the vlan however the lan lite software does not support port ACL's. Any way to accomplish this with this switch.
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[Code]...
View 5 Replies
View Related
Feb 2, 2011
I have AIR-AP1141N-A-K9 access point, but can not get over 130 Mbps speed. Looking at the manual it appears that I need to set "channel width" to 40-above or 40-below, but it only accepts 20. Is the 2.4Ghz radio limited to 20Mhz? Since the specs indicate that it can do 300Mbps, I must be misunderstanding something.
View 4 Replies
View Related
Sep 3, 2012
I'm trying to turn off the LED on a Cisco Aironet 1141 p/n AIR-AP1141N-A-K9. This is a standalone AP and from the CLI I'm issuing this command:
ap(config)#led display off
The LED does not turn off after typing this command. If I do `show run' it shows up in the config so the command was accepted. Is there a different way to turn off the LED? I'm running IOS Version 12.4(21a)JA1.
View 4 Replies
View Related
Aug 29, 2011
Trying to find a way to configure my 851 for home use. My internet provider use PPPoE with PAP and althrough I found many configuration options they all are incomplete...or i cant find the logic behind those commands. First of all I need to say what I need:
1. Configurate my int Fa4 (WAN) with pppoe so when i insert my ISP cable in it it will negotiate and take IP.
2. Configurate DHCP on LAN (Fa0-3) so that when I insert my PC it will take a fake IP.
Here is the place where i found some conf examples: [URL] and I have some questions:
1. MTU - Should I use the 1492 value or the "pppoe-client ppp-max-payload 1500"?
2. ip route 10.10.25.2 255.255.255.255 dialer 0 - How can i set an IP route when my connexion informations only come after i connect? (Because is PPPoE)?
3. I cant configurate the DHCP because I dont know the default route, I dont know the DNS, and i dont know the default gateway because I dont know them due to PPPoE !
View 20 Replies
View Related
May 21, 2013
I have two access points that I recently purchased from ebay. I updated them both to c1140-k9w7-mx.152-2.JB and I have been unsuccessful at getting either of them to connect at faster than 39MBps. After scouring google for answers I found several with the issue of not using the correct WPA2/AES configuration and that was me. However after changing the configuration, I am still unable to connect to either of the APs at faster than the 39Mbps. [code]
View 4 Replies
View Related
Dec 18, 2011
I have 2 Cisco 1141 aironets access points.
I've fallowed this tutorial: [URL]
I have an Ubuntu server running free radius authenticating against an LDAP server. Now I'm able to log into the AP via ssh with my LDAP credentials.
What I can't figure out is how do I setup the AP so when people connect to the AP's wireless they are prompted to use their LDAP credentials.
View 7 Replies
View Related
Mar 24, 2013
We have about 15-20 APs out in the field, and at random they seem to disassociate from the WLCs and re-associate within a few minutes. We have not looked into that entirely yet, but we are having an issue with a few. Sometimes, they will disassociate and after a few hours reassociate.
View 9 Replies
View Related
May 18, 2012
I have an aironet 1141 with multiple v lans configured, all with wpa2 but I need to put mac filter on only one v lan, so I follow this manual: [URL}. Basically is mac a ACL and applied to sub interface. So, I can associate to the AP, but no one can transmit or receive . If i remove the ACL all works fine.
My config:
access-list 700 permit <maclist> 0000.0000.0000
access-list 700 deny 0000.0000.0000 ffff.ffff.ffff
interface Dot11Radio0.130
[code]....
View 8 Replies
View Related
Oct 5, 2011
I have a problem putting a Cisco 1141 AP in repeater mode with a AP HP Procurve.Root AP is a the Procurve, but when try to put the Cisco AP with same SSID, Authentication, etc, I receive this error:
%DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: NO Aironet Extension IE
I try disable the Aironet Extensions and always get the same error all time. It's possible connect both APs?
View 6 Replies
View Related
