I have a project ahead and I need to clarify some things before starting this project. I will install a new WLC 5508 and I have 8 AIR-BR1310G-A-K9-R, so Im wondering if I can use them.
- Can this model be converted to LAP?, right now they are autonomous.
- I need to used them as AP not bridge and under the governance of a WLC. Could this be possible?
- The intention is to use them for outdoor operation. Should I use one or two outdoor antennas?.
- ANT-2506 could be a good choice?.
I have connected the AIR-BR1310G and one meter apart I installed a GPS antenna. When the AIR-BR1310G is up, the GPS stop detecting satellites. Using a spectrum analyzer I found that the AIR-BR1310G transmits a frequency of 1575 MHz along with the normal 2.4 GHz one. How can I eliminate this annoying 1575 MHz signal from the AIR-BR1310G?
I am trying to install AC3.1 on windows7 64-bit. But i get the error installation ended prematurely without any reasons for failure. I posted the errors here. I tried installing AC3.0 on windows xp and i get same problem. NAM is not getting installed . I just want to use the AC client to connect to wireless network.
I have cable internet with a wireless router. My home computer/internet works fine My second computer connected via wireless was recently infected with a virus and I had to do a complete system restore. Since doing that, I cannot establish a connection. My computer can find the wireless connections and the wireless network connection shows enabled show that it but no IP address. If I repair, I get the error message "TCP/IP is not enabled". I tried enabling, reinstalling, I have tried every suggestion on this topic that I have found in other forums (running command, etc).
I have one AIR-WLC2125-K9 installed and controll 25 APs,
Now i want to add some APs, so i have asked my supplier and he propose to add an other AIR-WLC2125-K9, i will have all APs contrlled by 2 x AIR-WLC2125-K9.
How can i add the second controller to work with the first one?
I want to reinstall the MSE image that was sent to me by Cisco TAC Team, however when I try to reinstall the MSE Application, however when I try to install it, the CD boots and show me the Red Hat enterprise image, then sends me black screen with the message "Kernel alive, Kernel direct mapping tables up to 480000000 @ 8000-1b000" and it stay there.
We have bought an 2504 Wireless Controller and now i want to download the newest Software, actually the Wireless Controller runs release 7.2.103. In the download section from Cisco i've found two "latest versions" the 7.0 with release date from 11.09.2012 and the other 7.3 with the release date 30.08.2012.
Now I'm a bit confused about this, because the higher release has an lower release date : Can you tell me the difference between this versions? and which version i should install?
We would like to install a wireless network throughout the station. Currently we have a wired network with 15 PC's and are looking at obtaining tablets for our squads and apparatus. The station is quite large and is divided by the vehicle bays.I'm thinking that we will need multiple access points throughout the station. I am familiar with setting up one wireless router but not with multiple access points.
I recently had to wipe (start all over again) my fathers PC as it become infected with a virus which I struggled to remove. When trying to set up the wireless connection via my virgin wireless manager I followed all the steps correctly until the last where it could not find my USB wireless adapter. I installed the latest software for the adapter from the netgear website but it will still not succesfully install the drivers fro the adapter.
I need to install a wireless PCI Adapter to my Dell Optiplex small form desktop computer, but how can i identify what type of PCI Bus slot do i have without opening the case.
My windows xp wireless drivers was functioning normally in my dell610.but accidentally i uninstalled it, now i am trying to install it but it ends up with an icon at the bottom which shows that it is installing but nothing is going on.i have tried this several time but i failed.
I received a new 2504 today, I consoled on and powered it up. I see the boot sequence starting all the services. Unfortunately that's about all I can do - i try to terminate the Auto-install script but even pressing the Enter key has no effect. I can ping the 2504 but HTTP just times out. The console cable and terminal software are fine (I use them daily on a number of Cisco devices). I have done a factory reset but the same thing happens.
So, I'm thinking the unit needs to be RMA'd ?
This is what is on the current session :- [Code] ........
I got a ISE 3315 with an IP-Plus license on it. Now I need to install a Wireless advanced license, but I got an error when trying. I've read that the wireless license doesn't need the ip-base one but I can't remove it?
Have a network already set up and I'm trying to add another laptop. I recall using a thump drive to install the last computers but can not remember how. Nor I can located original install disk.
I just reinstalled XP on my Dell inspiron 1100. Everything works good expect I can't connect wireless to the internet. I use my Ethernet cable and everything works great. The wireless setting say's I'm connected with excellent strength, also I have an IP address. I went to disk management and check for conflicts and noticed the PCI modem was yellow. I was told to disable it because I don't use a modem so it should not be a problem.
My computer crashed the other day and HDD failed. i finally got it back up and running but ive been using a usb wireless adapter. i do not have the disk anymore to install the drivers, nor will my computer install them from the internet because i dont have an internet connection on my desktop. what are my options to have them installed?
I have a wireless set up at home and recently had to replace my DSL modem (due to my cat knocking over my coffee cup and spilling coffee on my old modem) I have managed to connect to the internet directly through the modem, but want to connect wireless. How can I connect my new modem to my old wireless network?
I recently re-installed Windows on my PC, and I had the Wireless-G PCI Adapter installed before I done the re-installation.Now I've re-installed Windows, the adapter doesn't work. Do I have to re-do the whole process again? Also, I didn't actually install it myself, so any detailed step-by-step tutorial?
I had a hard drive failure recently and replaced my HDD with an identical HDD (WD 500 AAKS) and did a restore from my WD Passport Essential. Everything works as before except I can't install my AE1000 wireless adapter. The OS recognizes the new hardware and I attempt instalation form the setup CD. Istallation goes until it gets to the "Installing" step and then it just stays there forever until it comes back with an error. I am accessing the internet now through a cat 5 ethernet hook-up.
Region : Argentina Model : TL-WR1043ND Hardware Version : V1 Firmware Version : 3.13.12
I just got one of these to replace my old wrt54g. Seems to me a lot of people are flashing theirs with dd-wrt or openwrt. I was wondering why exactly. Unlike the old wrt54g, the tp-link stock firmware supports a lot of features in my view, especially the so wanted QOS. Do the CFW give the wr1043nd more stability or maybe better performance? Or is it about features? What features a CFW would add to the stock fw?
I reinstalled my windows7 again, because my laptop was jamming so much. But i cant connect to internet via wireless. I dont have any other options to connect my computer to internet other than using wi fi. I think it says i didnt install the wifi driver. i tried something, but it didnt work. btw i have inspiron 15r bought in the end of 2010
