I am wanting to use a Cisco Aironet 1552EU to use on a site survey for a future deployment and I need to know if it is possible to configure the AP to broadcast an SSID so that my team can search for that SSID and view the signal strength throughout the site. Is a WLC required to set the SSID or is there an SSID that will be broadcast by default that we can try to connect to?
View 1 RepliesWe are in need to perform a site survey with the Aironet 1041N Access Point.
Upon reviewing the site survey software, it seems you need to use an Aironet adapter. However from what i can tell, all the Aironet adapters are PCMICA cards, which most modern laptops do not have, and the PCMICA cards that do exist don't have drivers for windows 7.
Are there USB adapters w/ Windows 7 drivers that can be used to perform a site survey?
I have a question about sitesurveying with ap3500's, I'm going to deploy a wireless network in a new building, i have a company that normaly does my site surveys.
I normally provide them with some AP's configured with a designated ssid and local power modes set to 50%, however this does not seem possible with the new 3500i's i'm willing to use, for there is no IOS image available for it. I dont have any network connectivity yet in this new building, so i cannot f.i place them in a separate ap-group and assign a dedicated wlan to them.
Is there any detailed documentation on the Site Survey Client mode on the AP 1200?When using this mode I cannot see any indication that it has associated withthe root AP. I would like to be able to pass traffic from the ethernet port to the root AP VIA the AP in client mode. The Ap in client mode shows the radio in blocking when in client mode, is this normal? Is there a way to manually change this to forwarding mode?
View 4 Replies View RelatedHow the full functionality of the Wireless Security and Spectrum Intelligence module is supported in autonomous mode for site survey use, or is a WSC required?
I'm wondering whether we need to invest in more survey/ spectrum analysis kit or could just use a 3602e with WSSI and the inbuilt Spectrum Expert?
I know that the deployment guide for 2600/3600 access points states that if you have surveyed for a 3600 deployment, you don't need to survey again for a 2600 deployment. As the the 3600 is the higher specification model, is it safe to assume the reverse? I.e. a site survey carried out using 2600 access points is valid for a 3600 deployment, or is this too simplistic?
View 5 Replies View RelatedHas any tried using a 3500 CleanAir AP as a site survey tool? Could you set it up in multiple locations temporarily and gather interference data and analize through WCS? This would use the 3500 AP like you would the Spectrum Expert product.
View 7 Replies View RelatedI've been trying to connect two DCS-942L to some netgear WNHD3004 (wireless access points a/n WPA2 personal) that I use as access point but I can't find them in the site survey (advanced settings then wireless setup in the camera page).I think I could set manually the network name, security mode and key but since I'm working remotly on these camera, I'm pretty sure it won't work and I'll loose connection (actually they are connected to other access points and work ok).An ipad and macbook pro is able to see and connect to these access points so I don't think they are the problem.I've updated the camera to the latest firmware (1.12 build 1608 agent version : 2.0.15-b11)
View 2 Replies View RelatedJust now my boss asked me to prepare to set up site-to-site VPN on Cisco 881 Integrated Services router to ASA 5505 router which is now running at the HQ side. I am now learning pdf file from Cisco which mention how to setup site-to-site VPN between Cisco 1812 IOS router and ASA 5505 router by using ASDM V6.1 and SDM V2.5. Can't find the paper for that Cisco 881 device.
View 4 Replies View RelatedI've just recently purchased the Aironet 1142n and am hoping to set it up as a repeater. I've followed the documentation here: [UEL] but am still having problems.
What I'm trying to achieve is: I have an adsl router (TP-link W8960N) at the front of the house but the wireless signal does not reach all the way to the end of the house. I am trying to set up the aironet 1142n to act as a repeater and place it in the middle of the house and hopefully that will extend the wireless signal to the end of the house and remove the dead spots. I would like to do this without having ethernet cables running all over the place and have been trying to configure the aironet 1142n to no avail. Every time I set the aironet 1142n to "repeater" it automatically coverts back to "access point" under role of radio network.
I guess my main question first of all is, can I set the aironet 1142n as a wireless repeater? And if so, where am I going wrong in my configuration?
I've just read that " Repeater access points running Cisco IOS software cannot associate to parent access points that that do not run Cisco IOS software."
Does this mean the aironet 1142n set up as a repeater will not work if the original access point (in this case, the TP Link adsl wireless router) isn't a cisco brand?
how to setup the Aironet 1602 (AIR-SAP1602I-E-K9) I have tried accessing it by various IPs like 10.0.0.1 or 192.168.1.254 but none of them work also when I monitor the connection using Wireshark I can't find out what its IP is.
View 4 Replies View RelatedI'm setting up site to site VPN on a RV110W router. The administrator guide site to site instructions don't match the options on the router.The first step tells you to click on VPN then Basic VPN Setup. The router under the VPN option only has three choices, (1) VPN Clients, (2) Certificate Management and (3) VPN Passthrough. I have upgraded to the latest firmware 1.0.0.9.
View 4 Replies View RelatedI am planning on setting up a site to site VPN with two ASA5505s across a WAN connection. Take a look at my setup and answer this. To get this started, I would need to get my ISP to route any traffic from my external IP address to which address: 192.168.100.220 or 10.255.255.2. I have never done this before. Inside port is 192.168.100.220, Outside port is 10.255.255.2
View 12 Replies View RelatedI am setting up a site to site IPSec VPN between two ASAs.I want to NAT an internal host that my VPN peer's network will be connecting to. So I need to make sure the traffic coming from this internal host is NATted before it enters the VPN tunnel as "interesting traffic"
So let's say remote network 192.168.20.0 /24 is connecting through IPSec VPN tunnel with peers 65.200.1.1 and 198.14.7.10 to host 10.100.1.7 on my network.I want to NAT host 10.100.1.7 to 192.168.100.5 to the remote network connects to the 192 address, not the 10 (I am using a ASA 5505)
I've recently purchased a 2504 Wireless controller, and I have 10 2600 APs to deploy. I think I've set up the wireless controller OK - there doesn't seem to be much that needs to be done! But I just can't seem to register an AP onto the system.
Just to briefly outline what I have done, I have connected to the Wireless Controller via terminal emulator and run through the setup, then I have connected OK to the web interface, and I am able to view and amend the controller's configuration. So I have setup a WLAN and thats about it.
Next up I have powered on one of my 2600 APs, and I am able to view it working via terminal emulator again. But I am seeing it continually running the same routine to connect to a controller, and all the time it just fails. Below is what I am seeing.
One thing that I am unsure about is that I am unable to connect to the AP config pages via web browser, using the IP 192.168.0.97 (although it does ping okay). Is that odd?
And the main question - why doesn't the AP connect to the wireless controller? Do the APs need to be authroized on the controller first? If I check the controller's web interface, under Monitor - Statistics - AP Join, I can see the AP listed with Status "Not Joined" but I don't know what I need to do to make it join!
*Mar 1 02:28:54.579: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.*Mar 1 02:28:57.583: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.*Mar 1 02:28:57.651: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.0.97, mask 255.255.255.0, hostname APb0fa.eb56.5abf(code)
I'm working on setting up an Aironet 1040 Wireless Access Point for my company. It's my first time setting up something like this, and I've run into a bit of trouble.
I created my first SSID easily enough, following the manual and guides online. I set up VLAN 1 as my native VLAN and linked it to my SSID with the encryption and security that I was told to use and it works great. However, my boss asked me to set up a second connection as well for guests at the office, and this is where my trouble starts.
I created VLAN 2, and then another SSID which I linked here. I set up encryption and security the same way, and I can see the network when I open up my network and sharing manager. I can connect to the network as well, but I either get a spinning blue icon where my signal strength indicator is or a few bars with a yellow caution sign, and Windows says 'Identifying...'. I've compared the two SSIDs using the console and the GUI and I can't seem to spot any obvious differences between them.
Is there a guide to set up a site to site VPN using 1841.
I have 3 points, 1 1841, 1 pix 506e and 1 ASA 5500. I need a good guide/manual to set up this. I would like to connect to any of the points, and be able to see all the infrastructure.
who's familiar with the asa 5505 could give me a basic walk through on setting up a site to site vpn between two of them. One of the previous guys set it up so that people can vpn in with the cisco client but that's a whole different problem. It disconnects after a while randomly.
View 3 Replies View RelatedI have a home lab trying to setup a site to site vpn between 2 cisco pix 501 devices but it does not work.
[Code]....
Below is the running configs for both Sites. We have always used Junipers prior to this. It does not appear that the tunnel is getting created.
Basic
Network A: (Dallas)
10.180.1.0 / 24
Network B: (Georgia)
[Code].....
I have recently purchase Aironet Access Point. I'm pretty new to Cisco systems and what i'm try to do is have the access point broadcast multiple SSIDs lets call them Guest and Admin. My problems is when i config router to have a DHCP address it works perfectly fine but when i assign a static IP it shows all the any connected device as unkown with IP 0.0.0.0. So i'm guessing i will need to setup a dhcp server. Is there a way access point can have its own DHCP server and IP address ( i don't want to use any from my STATIC ip subnet as i dont know alot of empty ones left) like home wifi router where they assign each device an IP like 192.168.0.1. Is this possible?
View 1 Replies View RelatedI have a Aironet 1240AG and have our main SSID set up on Radio0-802.11G. It uses WPA TKIP. Everything works fine on it. Recently we have been getting a lot of visitors who need wireless access, so reather than hand out our main key to visitors, I decided to create another SSID on Radio1-802.11A for guests. For some reason the new SSID does not show up on the available networks on client devices. You can connect to it manually by entering the name and key. But how do I get the SSID to broadcast on the 2nd SSID. A lot of these guests are not very computer smart, so it becomes a real pain to have to walk them through connecting to the guest network.
View 3 Replies View RelatedSome deep technical questions regarding the AP541N access point? What I want to know is, if the AP has: - Watchdog per IP - ACK time adjusting - Site Survey.
View 1 Replies View Relatedhow to set-up cisco site to site vpn having dynamic ip address on both sides??
View 2 Replies View Relatedlinks with information / guidelines for the initial setup for this Access Point?
View 7 Replies View RelatedI bought 2 Cisco 1140 series Access Points a couple of months ago. We would like to use PEAP to autheticate with Microsoft IAS Radius Server & Active directory. I cannot find a document which describes how to setup this type of configuration. The only document which is close is how to setup LEAP & with ACS: [URL] I initially followed the 'TechReplublic's Ultimate Guide to Enterprise Wireless LAN Security' which has all the steps to setup Radius server, client side configuration, Certificates and finally a handy excel script to generate a config for the AP. This did not work. [URL] I am now trying to configure the AP using the Web GUI. I can see the network on the client machine but when I try to connect it timesout.
View 1 Replies View RelatedI have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies View RelatedWe have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?
View 1 Replies View RelatedThe scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration...
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad
[code]....
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies View RelatedAt the main site, I have 3 5508 WLCs each part of a mobility group (wlcMain-MG). In NCS, under "System/Mobility Groups" for each controller, I see each controller listed as "local" with the other Controllers listed with the group name "wlcMain-MG". None of the SSIDs are "anchored".
I have a new site with a 2500 series WLC that I would like to push out 2 SSIDs. This site contains two customers. One customer is the Main customer with the second customer leasing space.
I have the Cust2 WLAN at the remote site set to have traffic egress out of a local interface on the 2500 WLC (this traffic is then tunnelled back to their Main location via an ASA which houses the DHCP scope for that vlan). I can connect to this SSID, obtain an IP Address off the ASA and am tunnelling without issue.
For the Cust1 WLAN at the remote site, I would like to broadcast an SSID from the Main location on those same APs which are registered to the 2500. It is my understanding, that I anchor the SSID at the Main site and identically configure the SSID at the remote site. This will allow the end user to authenticate to the RADIUS server at the Main site and be placed upon the correct vlan (we are using DOT1x and dynamic vlans).
For my test, I am starting simple. I have created a test WLAN with no authentication. At the main site, on 5508 WLC3, I have created the test WLAN, and placed the interface into a low security vlan (call it VLAN-low). I have anchored this test WLAN to that controller. At the remote site, I have created the same WLAN (but placed it into the management interface for now - the VLAN-low does not exist at the remote site) and configured that WLAN to anchor back to the WLC3 at the main site. I am unable to obtain an IP address from the remote site. I have placed the remote site WLC in the wlcMain-MG as well. How close does the code need to be on the controllers - the 5508s are at 7.0.116.0 and the 2500 is at 7.0.220.0? What could I be missing?
I have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
View 3 Replies View Relatedi have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies View Related