Has any tried using a 3500 CleanAir AP as a site survey tool? Could you set it up in multiple locations temporarily and gather interference data and analize through WCS? This would use the 3500 AP like you would the Spectrum Expert product.
View 7 RepliesI have a question about sitesurveying with ap3500's, I'm going to deploy a wireless network in a new building, i have a company that normaly does my site surveys.
I normally provide them with some AP's configured with a designated ssid and local power modes set to 50%, however this does not seem possible with the new 3500i's i'm willing to use, for there is no IOS image available for it. I dont have any network connectivity yet in this new building, so i cannot f.i place them in a separate ap-group and assign a dedicated wlan to them.
Is there any detailed documentation on the Site Survey Client mode on the AP 1200?When using this mode I cannot see any indication that it has associated withthe root AP. I would like to be able to pass traffic from the ethernet port to the root AP VIA the AP in client mode. The Ap in client mode shows the radio in blocking when in client mode, is this normal? Is there a way to manually change this to forwarding mode?
View 4 Replies View RelatedHow the full functionality of the Wireless Security and Spectrum Intelligence module is supported in autonomous mode for site survey use, or is a WSC required?
I'm wondering whether we need to invest in more survey/ spectrum analysis kit or could just use a 3602e with WSSI and the inbuilt Spectrum Expert?
I've been trying to connect two DCS-942L to some netgear WNHD3004 (wireless access points a/n WPA2 personal) that I use as access point but I can't find them in the site survey (advanced settings then wireless setup in the camera page).I think I could set manually the network name, security mode and key but since I'm working remotly on these camera, I'm pretty sure it won't work and I'll loose connection (actually they are connected to other access points and work ok).An ipad and macbook pro is able to see and connect to these access points so I don't think they are the problem.I've updated the camera to the latest firmware (1.12 build 1608 agent version : 2.0.15-b11)
View 2 Replies View RelatedI am wanting to use a Cisco Aironet 1552EU to use on a site survey for a future deployment and I need to know if it is possible to configure the AP to broadcast an SSID so that my team can search for that SSID and view the signal strength throughout the site. Is a WLC required to set the SSID or is there an SSID that will be broadcast by default that we can try to connect to?
View 1 Replies View RelatedI know that the deployment guide for 2600/3600 access points states that if you have surveyed for a 3600 deployment, you don't need to survey again for a 2600 deployment. As the the 3600 is the higher specification model, is it safe to assume the reverse? I.e. a site survey carried out using 2600 access points is valid for a 3600 deployment, or is this too simplistic?
View 5 Replies View RelatedWe are in need to perform a site survey with the Aironet 1041N Access Point.
Upon reviewing the site survey software, it seems you need to use an Aironet adapter. However from what i can tell, all the Aironet adapters are PCMICA cards, which most modern laptops do not have, and the PCMICA cards that do exist don't have drivers for windows 7.
Are there USB adapters w/ Windows 7 drivers that can be used to perform a site survey?
Some deep technical questions regarding the AP541N access point? What I want to know is, if the AP has: - Watchdog per IP - ACK time adjusting - Site Survey.
View 1 Replies View RelatedI have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies View RelatedWe have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?
View 1 Replies View RelatedThe scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration...
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad
[code]....
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies View RelatedI have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
View 3 Replies View Relatedi have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies View Relatedi want configure VPN between backoffice which have ASA5510 firewall with static IP and site which have cisco router 1861 with dynamic IP.
how i can configure the site to site between them?
Just upgraded our WCS server to the 7.x code over the weekend. Turned up the first 3500 series AP's today. The AP's have been up for about an hour. I am seeing the Air Quality graphs on WCS. On the Worst 802.11a/n and 802.11b/g/n Interferers windows, I am see a WCS System Error Page message but only in those windows. I have gone over the documentation and dont see that I need to enable anything else on WCS.
View 10 Replies View RelatedWe are planning to implement Aironet 3500, Do we need to have controller to install it or can we install as standlone AP.
View 1 Replies View RelatedI'm trying to find if the 3500 AP will contains an 802.1X supplicant, so the AP can be identified and authorized by an ACS when it is connected to a secure access switch.I can find plenty of info on WPA2 & 802.1X for the wireless clients, but I'm struggling to find anything on 802.1X for the AP itself.
View 1 Replies View Relatedwe demo'd a 3500 with CleanAir before working with Cisco and purchasing a first batch. The demo worked as expected, just plugged it in and it went to town serving clients and reporting on it's channel in local mode, no problem. My first batch I have two AP's, 3502i's to be exact, plugged in and running on my 5508 with 7.0.98.0 code and and NCS Demo. The AP is up and serving in local mode, however NCS says CleanAir Management Operation StateDown
I took a look at the WLC and it says:
CleanAir
Oper
Status DOWN
So, why.. and where do I put it UP.BTW, this AP is connected to a 3750x stack, shouldn't be an issue there...
For a Campus setup (University), if I deploy 1142 AP's on all the floors with a WLC controlling them, and put one 3500 AP on each floor, will that give sufficient Clean Air support with automatic Rogue elimination? What about if an AP drops, does the WLC automatically try to cover that area with neighboring AP's? I know the old WLSE would be able to do that, but not sure if the WLC can do that by itself. What part of Self Healing can the WLC do with Clean Air, or is a WCS a must have in order to automatically Defend and self heal? Also is the MSE needed for this if a WCS is used? What does the MSE do that the WLC and WCS can't?
View 4 Replies View RelatedWe have a Sonicwall NSA 3500. We have a seperate interface for LAN and WLAN. The WLAN is set up on a Sonicpoint. Right now, the LAN gives out 10.10.99.x addresses, the WLAN gives out 10.10.100.x addresses. What is the best way to get these two interfaces to give out addresses on the same scheme, ie both LAN and WLAN giving out 10.10.99.x addresses?
View 1 Replies View RelatedI am trying to config my wireless lan controller (WLC) 2106 to discover my new 3500 access points.I followed the example Cisco configuration doc.69719.I am using a Cisco 3760 switch to interconnect the AP and WLC.I set up DHCP in the switch. [code]
View 6 Replies View RelatedFollowing best practices on cisco documentations we did set aaa acounting update periodic 5 with 250 switches in the deployment every single switch is geneating and sending 9.990 acct records this is too much the new testing parameterswe are using is aaa acounting update newinfo periodic 15 and this lowered accts by 2/3 (3500) moreover from switch monitoring the most accts records sent by it are related to the trunk-port any suggestion to mitigate this informations storm rather than raising the 15 min period to higher values?are this records generating from the trunk port normal?
View 1 Replies View RelatedThe problem am having is that my Users can get to the internet on the LAN but cannot get to the internet thro the WLAN. Below is the cisco equipment used to setup the WLAN and LAN. I dont have any clue as to why users cnnot get to the internet from the WLAN except the LAN.
ITEMS
1.
CISCO CATALYST 2960-S
Part Number: WS-C2960S-24PS-L
10
Part Number: CON-SNT-2960S2PS
10
[code]....
So I'm going to bridge two Cisco AP's 1260 and 3500, which have an 880 router on each side.
(Currently I have a VPN set-up through the internet for the two locations to communicate) (Naturally they are currently in different subnets) Will absolutely change this and set up as one subnet. There is VLANs setup on each router (same VLANs)
VLAN 1
And
VLAN 10
Everything is configured on the Routers and AP's for these VLANs (works flawlessly over the VPN).
So now since I’m going to get rid of the VPN and set-up a bridge with two AP's, will having same VLANs across both routers be a problem? Will VLANs work OK through the bridge?
Besides using (IP helper address DHCP-IP) command on the non-root bridge side router to forward DHCP requests to the root bridge side router, Also I want to be able to route internet traffic on the non-root bridge side through the WAN port, and only route LAN traffic through the bridge..
In regards to QoS profiles on the WLC. I have applied a profile to a newly created WLAN and set the Per User Bandwidth to 512k and it seems to be kicking in on the ingress only, this is supposed to work ingress AND egress or is it just designed to work one way? I have a 4402-25 with Cisco 3500 AP's and am running the 7.0.98 code. If it is designed to work one way only is there a different way to apply it ingress and egress simultaneously off the WLC?
View 3 Replies View RelatedWe have couple of Cisco Aironet 3500 Series access points with the following P/N: "AIR-CAP3501E-A-K9", we have discovered that we need a wireless LAN controller to connect those new access points!, however, we do not have any wireless controller in our LAN.
We even tried to CLI through the console port but we could not set any static IP on it!, after reading on Cisco site we discover that this type of AP is called "Lightweight Access Point" LAP which handles all the management tasks to the controller!
So what shall we do! is it impossible to operate them without the controller?
We have had several APs disassociating from our controllers. The alerts say, Message: Access Point 'AP-xxxxx' associated to controller '10.x.x.x' on port number '0'. Reason for association 'Dot11g Mode Change. I have read several posts that point out that you should have QoS implemented to prioritize the CAPWAP traffic. I'd like to know if someone has implemented QoS and whether it has been successful in stopping the APs from disassociating. And if it has been successful do you have any configuration examples for the ports attached to the AP and controller as well as the QoS configuration?
We have several sites with AP1142's and 3500's. We have 2 5508 controllers. We are broadcasting 2 SSIDs of which one is in HREAP mode and the other is in local mode. Each of our sites have MPLS circuits.
Here is an example I found on Cisco which I believe can be used for CAPWAP as long as you change the ports to 5246 & 5247 instead of 12222 & 12223.
Example Router Configurations #
This section contains router configuration examples to be used as guides when addressing CS6 remarking or LWAPP control traffic load.
#
This example uses LWAPP APs on the 192.168.101.0/24 subnet, and two WLCs with ap-managers at 192.168.60.11, and 192.168.62.11. (code)
I am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
View 4 Replies View RelatedI have an ASA 5525 and need to configure site to site ipsec vpn to 3 peers. I currently have an existing /28 public address from my ISP that is used by other services.Is there a way to use this existing ip range to configure IPSEC tunnels to 3 peers ?
View 10 Replies View RelatedI configurated Ipsec vpn at asa 5510. my inside ip 192.168.10.156my public ip: 85.x.x.xmy peer ip : 62.x.x.x
the project is that:
the remote site want the interesting traffic like that:
source ip 172.16.1.104 can access destination ip 10.0.154.27
My inside ip is 192.168.10.0/0 and i can not to change it 172.16.1.0/24 and i can not to add this ip at my network.
I would like to know both Cisco 2901 or 2921 router and Cisco 5505 ASA can build site to site VPN.
1) what is the different to build site to site VPN between router and firewall ?
2) which is the best choice if using in site to site VPN connection ?