Cisco Wireless :: Upgrade WCS 7.0 To PI 1.2 Via NCS 1.1
Feb 18, 2013
we have started to do the upgrade from WCS 7.0 to PI12. In order to do that we first need to upgrade to NCS 1.1. We have ordered the following from Cisco:
R-W-PI12-M-K9WCS 7.0 to Cisco Prime Infrastructure 1.2 MigrationN/A14 daysNoN/A11.995,00 1.995,00 01.995,00 R-PI12-BASE-K9Prime Infrastructure 1.2 Base License and SoftwareN/A14 daysYesN/A10,00 0,00 00,00 L-PI12-LF-500-
[Code]....
L-WCS-NCS1-M-K9 is the Product Number to do the upgrade from WCS 7.0 to NCS 1.0, R-WCS-PI11-M-K9 is the product number to dothe upgrade from WCS 7.0 to NCS/PI 1.1.
If I try to install just the License File I get from Cisco using the XML file from our WCS 7.0 installation, I get the error "Unable to add any license without an NCS (L-NCS-1.0-K9) license.".
But how do a get this license if I ordered R-W-PI12-M-K9 (WCS 7.0 to PI1.2 Upgrade License)? What is the step to get the right License?
View 15 Replies
ADVERTISEMENT
Sep 29, 2011
I have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is blocking. I have added rules and then even tried disabling the firewalls completely on both computers and still no success.
View 7 Replies
View Related
Jun 19, 2012
I am facing a problem to install a ap upgrade lic file on controller 5500. Iam getting the following error:
% Error: License file transfer failed - Error from server: File not found
I have confusion here that when I configure this command from GUI
tftp://172.32.45.22/cmm/standard.lic
What i should use for /cmm/ ????
Let say i have lic. file is on desktop of tftp server computer and I say in this command
tftp://10.12.70.35/??/license file .lic
View 6 Replies
View Related
Sep 10, 2012
Is it possible to upgrade the CSACS-1121-UP-K9 to be a non upgrade part? We were going to upgrade from a Windows 4.x to the above Appliance (version 5.x) but there is now a reason to keep the old Windows version running therefore we cannot give the new Appliance the old ACS's licenses?!So we should have (with hindsight) bought a fresh version of the ACS 5.x rather than an upgrade.
View 1 Replies
View Related
Jan 22, 2013
I'm planning to upgrade our WLC 2504 from 7.2.111.3 to 7.4.100.0 but the cisco site says "WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be managed, Version 1.3 is not yet available to download at this point of time" Is it something about NCS? we have only 1 cisco WLC 2504 and 6 1142APs.. Also let me know is it possible to go directly from 7.2 to 7.4 ?
View 8 Replies
View Related
Sep 17, 2012
We have some new WISM2 running 7.0.116.0, but now we need to upgrade their license to suport 1000 APs. So I am looking at upgrading the software to 7.2.110.0. We are running WCS at the moment and got NCS with the new WISM2, so going to 7.3 and buying Prime Infrastructure is not an option at the moment, thus we are going for 7.2.
The thing is I can't seem to find much info about this upgrade. Is 7.0->7.2 a smooth upgrade? Do we need to do any configuration changes to the WISM2 or LAP1242? We are running H-REAP, will the change to FlexConnect be affected? I can't seem to find anything regarding requirements for 6500/SUP for running WISM2 7.2, do I need a certain software for that?
View 5 Replies
View Related
Apr 25, 2013
I am planning to upgrade WLC from 7.2.103.0 to 7.2.110.0 due to some bug, but I wanted to know if it is compatible with WCS - 7.0.240.0 and NAC Guest server version 2.1.0, I am made some search but I couldn't get to proper conclusion.
View 8 Replies
View Related
Mar 25, 2013
In order to enbale HA SSO on our two 5008 WLC's, I plan to upgrade them to 7.3 / 7.4 (currently 7.2)Right now 7.3.112.0 is the latest release. We do not have any 1600 series AP's, which requires 7.4.any reason going for 7.4 directly..or not going for it?
View 5 Replies
View Related
Feb 11, 2013
I want to update an AIR-LAP1522AG-N-KP. I want to use TFTP. The problem is that my laptop does not ping any of the interfaces of LWAP.For example:Laptop 192.168.1.100 / LWAP Gigabit0 192.168.1.101 - - ping fails . I have experience using AIR-LAṔ1242AG , or the process is different?
View 5 Replies
View Related
Jun 29, 2011
Since we have now got a go for upgrading the IOS I have a little difficaulties finding if the current IOS will upgrade correctly to the advised version without any loss.Current version is (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF7 In the realease notes for IOS 12.2(33)SXJ I can't find any upgrade matrix or upgrade train.Will this version upgrade without causing any mishaps on current WiSM(ver.1) and switch config?I didn't get any adequate answer, but since NO ONE did mention any repercussions, we did the upgrade......and we did loose configuration !Still the WiSM (version 1) is working all right, but where did the related WiSM configuration go?.How can you do a span session if you have no interface to tie onto?
View 7 Replies
View Related
Dec 3, 2012
I am planing to upgrade 2 of my 5508 series WLC from 7.0.116 to version 7.2.111.3. I understand that legacy AP's are no longer supported. Is the upgrade straight-forward just like other code upgrades?
View 19 Replies
View Related
Jan 18, 2012
Any info on performing this upgrade. The release notes that I have looked over make it sound like if I want to do the data migration that I must first upgrade the MSE to version 7.0.201.204 and then go to 7.0.220.0. This is only what I have come up with, this isn't clearly stated from what I have read. How to performe this upgrade with the data migration?
[URL]
View 1 Replies
View Related
Mar 12, 2013
I want to upgrade the WLC 5500 from 7.0.220.0 to 7.3.112.0, coul be any risk if i do the upgrade..?
View 2 Replies
View Related
Feb 20, 2012
After upgrading, ping times from clients has gone from ~10ms to ~2500ms. I have a Cisco 7500 Flex controller, when running controller code version 7.0.220.0 client performance was as expected. When using code 7.2.103.0 performance is terrible. I have tried upgrade to 7.2.103.0 and clean configuration (reset) with 7.2.103.0 with the same results.
I have tested using 3502i APs with the signal metrics (from AP) reported by the clients (all testing close to these figures):
Signal Strength : -48 dBm
Signal to Noise : 49 dB
AP's are in HREAP/Flex mode. The WLANs use HREAP/FlexConnect local switching. I have tested WLAN's with WPA2-PSK and 802.1x/WPA2 with the same results. I have tested several clientsoperatign systems , laptops, ipads, iphone. All experience consitent poor ping latency peformance on both 2.4Ghz and 5 Ghz when using controller code 7.2.103.0.
I have switched between 7.0.220.0 and 7.2.103.0 several times and the results are consistent; good performance on 7.0.220.0 and terrible performance on 7.2.103.0. I would like to use 7.2.103.0 for its enhanced FlexConnect features but this is a real show stopper.
View 8 Replies
View Related
Apr 26, 2013
We have WCS running 7.0.164.3...We had upgraded WLSE to WCS a few years back.
I am planning to upgrade WCS to 7.0.240.0... What is the procedure of upgrading WCS in this case? I am not quite sure about the procedure as our WCS was a WLSE before.
View 3 Replies
View Related
Apr 19, 2013
I am planning to upgrade the WLC code and I have about 133 RAPs/MAPs/1131 APs that already joined the WLC. Will I have a problem with my MAPs when the WLC starts upgrading the code. Some MAPs will have 3 hops to connect to a RAP.
View 11 Replies
View Related
Jan 24, 2012
I have run into a major issue with an autonomous Cisco 1142AP. We were in the midst of a firmware upgrade when something went wrong and caused the AP to reboot in an error mode. Basically the unit was flashing Blue, amber, red. We unmounted the unit from the wall, connected to the console, and it would now only flash red over and over. We pulled out the cisco guides and performed a factory reset on the unit. This still does not work. and the contents of our flash directory is empty. All we get is a ROMMON AP prompt on the unit. If I issue a set command, I can see the default settings for IP, netmask, etc.
I cannot access the unit via the network, even after setting IP info and matching it up to my laptop. Since I have no network connectivity, I can't TFTP a new IOS file to the unit. I am stumped. How to get the config as if it was out of the box, or an alternate way to TFTP to the unit? [code]Notice the lines in red, I must have typed someting incorrectly.Now once the unit boots after being reset, I cannot even type in the CLI. Someting majorly screwed up here. Can the bootstrap be reinitialized?
View 3 Replies
View Related
Feb 3, 2013
Our company has a customer with a Cisco 4402 WLC and a code version of 4.2.130.0 . The customer wants to upgrade the code to 7.0.230.0. Is there any flash size requirement when upgrading to 7.0.230.0? (upgrade train: 4.2.130.0 ----> 4.2.209.0 ----> 7.0.230.0), How can I find the flash size?
View 2 Replies
View Related
Apr 2, 2012
I want to upgrade all my controllers (a mix of 4400 and 5508) to 7.2.103.0 from 7.0.116.0. Can I make that jump or should I do incremental?
View 7 Replies
View Related
Sep 28, 2010
A customer has wireless LAN controller with version 4.2.205.0 and i want to upgrade it to version 7.do i need to upgrade the controller to intermediate version or i cant directly upgrade it.
View 2 Replies
View Related
May 21, 2013
How to upgrade the IOS of the Integrated wireless AP in a Cisco 881W using TFTP server (I do have software)Router side is not an issue it is the integrated AP that gives problem?
View 14 Replies
View Related
Feb 14, 2013
I have succeeded in turning the AP from autonomous into LWAPP mode with the Ugrade tool. The AP has been loaded with c1130-rcvk9w8-tar.124-10b.jda due to the upgrade tool version 3.4,After reboot, the AP appears on the vwlc (YES!) however as you can see in APvwlc.jpg the AP now have version 3.0.51.0.I need the AP to be loaded with version 7.3.101.0 with FlexConnect mode.
View 24 Replies
View Related
Jun 16, 2013
upgrade on the wireless controller 2504 from 7.0 to 7.4 is direct upgrade.My customer faced problem by upgrading the software 7.0 to 7.4 directly and the image hang.how should proceed recover the image 7.4/
View 7 Replies
View Related
May 21, 2013
Currently I am using WLC 2504 with Software version 7.0.220.0. I am having some issues with Windows 8 clients they can't connect and I read on couple of review that wlc needs upgrade software.
I checked and latest versin is 7.4. Can I go to this version directly or I have to jump step by step.
View 3 Replies
View Related
Nov 3, 2012
i have cisco 1260 Access point with standalone ios ap3g1-k9w7-tar.124-23c. i download new IOS to connect the AP to the controller the new ios is ap3g1-k9w8-tar.124-23c.JA5.tar. upgrade th AP to LAP. is it just install ios like in router & switch by tftp?
View 1 Replies
View Related
Nov 6, 2012
I have 3 ap541n's in a cluster. I have upgraded 2 of them to 2.04 firmware. The third did not take the upgrade well and hung during the process. I have tried factory reset it but to no avail.
The AP's are on a simple network - they get their IP's via DHCP.
View 1 Replies
View Related
Nov 7, 2011
I ##have a customer with WLC 4402 in use, running software version 7.0.98.0, and supporting 11 APs at present. The customer wants to enlarge the WLAN, which involves increasing the number of APs. I #####have purchased a new WLC5508, and have installed it onto the network alongside the 4402. the 5508 is running software version 7.0.116.0. Because the wireless network is critical to the user, we want to move the APs over to the new controller while the network is up and running, then remove the 4402.
However, when we set the 5508 as the master controller, or tell one of the APs to use the 5508 as its primary controller, the AP connects to the new controller, downloads the new software version, attempts to load it but reports an error with the unzipped file size of the software and fails to boot. formatting the flash on the AP, then disconnecting the 5508 from the network and rebooting the AP allows it to connect to the 4402, it downloads the older software and boots as normal. A new AP, if connected to the 5508 in a test scenario (ie no 4402) connects, downloads and boots perfectly.
I #have the upgrade software to allow the 4402 to be upgraded to 7.0.116.0, but I am concerned that, if this is installed, the existing APs will then fail to boot from the 4402 or the 5508.all APs are 3502s, running IOS version 12.04(23c)JA when connected to the 4402 and 12.04(23c)JA2 on the 5508.
View 7 Replies
View Related
Mar 24, 2012
I 'm trying to upgrade WLC 4402 up from 5.1.151. After upgrade to 5.2 or higher https interface is inaccessible. If I use any other previous version, all is OK. Somewhere I found recomendation to open http before upgrade and use it at first. It works, but what to do next? To stay on http only?
View 1 Replies
View Related
Apr 23, 2013
my client claimed that right after thry upgraded their WLC 4402 to version 7.0.220.0 from the version that came preinstalled (factory) the can no longer console into the device. They were able to console into the 4402 before the upgrade but now they can't. I'm thinking that maybe they upgraded straight to the new version and didn't verify to see whether they were allowed to upgrade directly to that version 7.0.220.0 or if they needed to upgrade to a intermediate version , the proceed to upgrade to the 7.0.220.0.
View 3 Replies
View Related
Jan 29, 2012
We are looking to upgrade our 5508 wireless controller from 7.0.98.0 to 7.0.220.0. Reason being, we have experienced a lot of access points disassociating from the controller as well as client authentication issues. Upgraded from 7.0.98.0 to 7.0.220.0 and any issues during the upgrade or after the upgrade?
View 3 Replies
View Related
Jan 9, 2013
I upgraded the firmware on my wap121 and the URL redirect option is now gone. The docs all talk about using Captive portal but that is only on a wap321. How can I get the redirect back so customers who connect to my network see the site for our bar before they go on the internet?
I upgraded from the 1.0.0.3 to the latest (1.0.2.3)
View 9 Replies
View Related
May 3, 2012
WLC-4402-25-K S/W - Primary and Secondary Controllers were running 4.2.130 to begin with. Customer upgraded remotely using NCS - Primary to 4.2.209 and then to 7.0.230 and all that went fine and is in Production.
Then customer upgraded Secondary also using NCS also from 4.2.130 to 4.2.209 in preparation to upgrade to 7.0.230 and he lost contact with the controller. Sent a technician to site to troubleshoot by connecting to Serial Port. Technician #ESCAPED out of the boot sequence and from the BOOT MENU tried to boot the Primary Image and it failed with CRC error on Flash. He then tried to boot the Backup image and had the same problem. He then tried to manually load 7.0.230 - ER (Boot Software) using TFTPD32.EXE and that went fine. He then tried to load 7.0.230 "aes" S/W - The big over 70 MB file and went through most of the file transfer but failed saying:
ERROR: Transfer Failed.
TFTPD32.EXE said something like "Data Packet too Short or some such thing". Sorry did not write down what TFTPD32.EXE said.
Then we thought "may be" a power cycle of the unit is required after the ER Boot Loader Image was loaded. When we did that the unit died. That is - no communication with the Serial Port. We don't think we have any choice other than RMA - Do we?
Customer says he did read and follow this link - especially Table 10-1. {URL}. He said he used NCS to do the Upgrade. I a not familiar with NCS.
View 2 Replies
View Related
Dec 9, 2011
After much investigation I finally found what I thought was the firmware upgrade for my WAP4400N access point, I downloaded the file which is a .img file which seems a bit off I think. Anyway when I go to the admin page it decides its an unknown file format. Could someone explain what I am supposed to do with it!
I have to say I am very dissapointed with the whole support function of this site it is very hard to navigate and when you do think you have the correct link, its not. How very helpful!!! I suppose there are networking gurus who look after multi 1000 user systems who understand how the site works and think its fantastic. I support 5 PC's and 7 laptops on top of my normal job, it should be easier.
View 2 Replies
View Related
