I have one L3 Switch which is connected to three L2 switches and then three WAP4410N devices are connected to L2 switch. I configured three diffrent VLANs for my users. i want to configure like this:- one VLAN for wired user, one VLAN for Wireless and one another wireless VLAN for the Guest user. guest user must have limited access. how can i configured wi-fi VLANs to my Wi-Fi device.
View 2 RepliesDoes the WAP4410N support Dynamic VLAN assignment by means of 802.1x authentication?
The reason why I ask this; I am able to configure a SSID on a WAP4410N with WPA2-Enterprise, in combination with 802.1x PEAP network authentication. I can succesfully connect Windows, Windows RT, Windows Phone, iOS and Android devices. But.. I am unable to designate them to another VLAN based on access/connection policies. For example; I want mobile devices such as iPhone and Windows Phone to be assigned to a specific VLAN. The Wireless Access Point (authenticator) must be able to support that.
This is my setup:
Spplicants: Windows 8 / iPad / ...
Authenticator: WAP4410N
Authentication Server: Microsoft NPS (Network Policy Server)
I used 802.1x PEAP (Protected EAP) with password (domain user) authentication. In fact, the suplicants communicate with 802.1x to the authenticator. The authenticator communicates with RADIUS to the authentication server. NAP is not in between. It's just plain 802.1x authentication.
wether dynamic VLAN assignment is supported?
We are trying to setup a WAP4410N with 2 SSID's. One SSID for our private network and the other for guest internet access. On the VLAN and QoS page there is a setting for priority. What would be the suggested values for this setting? We obviously want our private network to receive priority over our guest network.Also, does VLAN Tag setting need to be on Tagged to determine private from guest traffic?
View 2 Replies View RelatedWe have two 3560G-TS-E running 12.2(35)se2, configured as HSRP. Both are running ntp config "ntp peer 210.72.145.44" and it's pretty well that they get the correct time. Yesterday I upgraded the second device to IOS 12.2(58)se2 and ntp doesn't work now. I checked doc that 12.2(58)se2 runs ntp default version 4 so I change to "ntp peer 210.72.145.44 version 3" but still not work. I put here "show ntp" result for different IOS.
IOS 12.2(35)
SW01>show ntp status
Clock is synchronized, stratum 2, reference is 210.72.145.44
nominal freq is 119.2092 Hz, actual freq is 119.2022 Hz, precision is 2**18
reference time is D2EF12A5.2EB2DCB2 (15:07:17.182 GMT Wed Feb 22 2012)
clock offset is -4.6616 msec, root delay is 57.50 msec
[code]...
Two 5548 switches running switch profile and it got out of sync (probably because one of the switches lost power before it has chance to save configure). Once the switch profile out of sync, you can't make any change to the switch profile any more, verification will fail.Is there any good way to get the switch profile re-sync without recreating it?
View 2 Replies View RelatedI have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
I have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
I have a Cisco SG200 26 Port Switch, 2 Cisco WAP4410N Access points, and a VLAN aware Router. I have created 4 VLAN's. For the sake of this conversation lets call them.
98 - Intel Vpro
99 - Management
100 - General
101 - Guest
The Access points are capable of doing V LAN tagging so I plan on having them tag a guest network as V LAN 101. That can get sent to the V LAN aware router and out. No problem. I have some devices, or management pages that I don't want accessible from the general network. (Intel V pro KVM, Remote Management Cards, AP Config Menus, Switch config menu...) . I need to be able to take a V LAN unaware device, plug it into port 1, and have it communicate with V LAN 98, 99 and 100.
From the broadband modem/router connected with a Gigabit 8 port unmanaged switch. Then, one WAP4410N is connected to the switch, wired connection for a distance of 90 meters. WAP4410N is set as an access point to the area. Then the second WAP4410N will be run as a repeater to the first WAP4410N. My question is that, can we set the second WAP4410N as a repeater, without the need for it to be connected to the switch via ethernet cable.
View 7 Replies View RelatedI added Linksys RV-016 16-ports VPN Router into the connection. RV-016 supported multiple subnets.
As mentioned in [URL], D-Link DIR-615 needs to be a device which could support multiple Vlan subnets. But unluckily DIR-615 does not support multiple Vlan subnets.
Therefore I added Linksys RV-016 in the the combination of devices. As what i found in RV-016 GUI setting, it supports multiple subnets.
Purpose outline:
1. Have to create two different SSIDs.
- SSID 1 for Management (able to view all other LAN devices)
- SSID 2 for guest and staff (unable to view all other LAN devices)
2. Create two VLANs in catalyst 2960s.
3. Create two subnets in Linksys RV-016 to accept two Vlans from catalyst 2960s.
Any experience of configuring RV-016 for the mentioned purpose above?
I did the config below but unable to obtain the ip from the subnet scope 10.10.9.0. The switch is in the layer 3 mode.
no spanning-tree
vlan database
vlan 2
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
[code]....
i am on pc i want same outlook on mac no delete on main xp pro home office pc. would like to received and send email from new mac book pro: fully synced between both?
View 1 Replies View RelatedI am trying to sync the vizio wireless tv to the router. I need the security code for the ubee router?
View 1 Replies View RelatedHow do I resync my wireless microsoft keyboard and mouse. I just switched out my power supply unit and now my keyboard and mouse is not working. It is a model 3000 and has a white usb receiver
View 1 Replies View RelatedI had been using a Linksys Wireless-N Router WRT350N with a Linksys Wireless-N Access Point WAP4400N. The router quit working so I upgraded to a Linksys Wireless-N Router E1550. The problem is, the new router doesn't sync with the old access point. how to setup the Access Point to sync with the new router?
View 1 Replies View RelatedI have 2 5508 controllers in a mobility group. Any good way to keep the configuration between the 2 controllers synched up?
I thought about copying the config from my primary controller to the secondary controller, but I would think there is a more elegant way to make this happen.
For test I used 2 Switch that name "ESW X" and "ESW Y" I have 2 network that I named "Network A" and "Network B" I build 2 VLAN for each network that named Vlan 2 for Network A and Vlan 3 for Network B, I don't use Vlan 1 because it's the default Vlan
Configuration ESW X:
port e1 : ACCESS PORT on UNTTAGGED Vlan 2
port e2 : ACCESS PORT on UNTTAGGED Vlan 2
port e3 : ACCESS PORT on UNTTAGGED Vlan 3
port e4 : ACCESS PORT on UNTTAGGED Vlan 3
port g3 : TRUNK PORT with UNTTAGGED Vlan 1(default) and TAGGED Vlan 2 and Vlan 3
[code]....
Each Vlan can't communicate between the two switch, I think they're a problem in my vlan/port configuration?
We have a L3 core switch with multiple VLANs setup. Is there a way to place an IPS so as to monitor the traffic passing between, lets say, VLANS 1-3 and VLANs 4-10?
View 3 Replies View Relatedsetting up two VLANs for my WAP: one for all local network and internet traffic and one for just (guest) internet traffic. I just purchased both devices but I don't know if I have the option for free Cisco phone support.
View 1 Replies View RelatedHow many VLANs does the ESW 500 switch support?
View 4 Replies View Relatednew to networking, I can not fully understand concepts like VLAN, so I would like to know whether it is possible to have a a few VLANs without a switch but over a bridge (created under linux - connecting a few virtual machines).
View 1 Replies View RelatedI have to admit I've never written my own Cisco configuration and I probably know just enough to break things. The last time I configured a Cisco was a few years ago, and the Wachovia people just told me what to type.
I have a Cisco WS-C3548-XL-EN and a Cisco WS-C3524-PWR-XL-EN "Inline Power" with default configurations and I want to setup VLANs. Basically, would this work?
SWITCH 1:Router on port 39, Wifi on Port 47, Uplink to 2nd switch's port 24 on port 48
Code:
en
conf t
interface VLAN10
no ip directed-broadcast
no ip route-cache
[code]....
And then I would test that it works, if it does issue #write memory, and it it doesn't powercycle and try again?
I'm Confused from the fact that Vlan tagging is done at access port and trunk port always gets tagged packets (untill its case of native vlan).But I still believe in other fact which says tagging happen only when a frame hit the trunk port which means trunk port gets untagged frame and tagging is not possible at access port.
Would like to know where actually this tagging happens ?
and also which command we can use to encapsulate 802.1q protocol to access port ? The way we do at trunk port is #switchport trunk encapsulation dot1q Is the above command applicable for access mode also?
I have a switch cisco c 3750 that has vlan information, how to remove vlan information.
View 1 Replies View Relatedi have a SG300-52 Switch, route mode is enabled, and it is using the latest IOS.I have created 4 Vlans in this switch, till this point its OK, but once i try to give ip addres to the created Vlan either from the GUI or CLI the switch is not responding. i have to go and manually reset the switch using a pin.
View 8 Replies View Related i was trying to set up a new SG300-52 L3 switch for switching and Vlan. The problem is that the vlans on this switch cannot get their DNS resolved. Probably a stupid thing i can't get to see, but i think it is a simple solution given switchin is not my expertise.So my setup:
- ISP Wan router: LAN ip 10.0.0.1, DMZ: 10.0.0.2 -> i have to use this router for ISP support. But it suckes, that's why we use own router for firewall, port forwarding etc.
- Nice Router: WAN: 10.0.0.2, LAN: 192.168.1.1
- SG300 L3 switch
This works. I can ping switch, nice router, ISP router and google's ip from VLAN 5.But i cannot ping google using host name. From within SG300 i can. So it has something to do with SG300 not doing DNS right.My Client on VLAN 5 has ip 10.1.1.5 / 24, default gateway and dns pointing to switch: 10.1.1.1.I have put an entry in DNS servers in SG300: 192.168.1.1 active (pointing to Nice router). On client leave default gateway pointing to switch. But put DNS server : 192.168.1.1
In our new Head office we have to set up a Network connectivity.Total our office 4 floors.In each floor we kept three cisco 2950 switch.We have L3 switch(cisco 3560) to connect the all the other switch.In our office total 5 departments.we have to create VLan for each departments in the switch.
We want to all user to communicate to each other.We have WAN connectivity in the router(cisco 2900) to connect the other office.First i want know how to physically connect all the swiches and finally with the L3 switch.How to configure the VLAN in both L2 and L3 switch.In our other client office one router to connect the both office.In the router how to configure and which protocol to use to communication.
Ip address:10.10.40.0/22
WAN IP :192.168.214.65/30
Are there any solution to connect VLAN 1002 configured in non-cisco switch to connect to Catalyst 6509?
View 2 Replies View RelatedI have the new firmware running on my SG500 switch. I've also just finished creating my VLANs. My issue is that I can't delete the old default VLAN .... VLAN 1. More importantly, I can't seem to get DNS to work on the switch.
When I set a DNS server, the VLAN defaults to VLAN 1, and the option is greyed out and can't be changed. Why is it VLAN1? Why is it greyed out? How do I get DNS to work on the switch, for services like Time Servers?
Planing to implement ARP out in all interface vlan at switche(6500,3500).It's useful to avoid unicast floating in the Switch.What are precaution to be take care during the implementation?
View 5 Replies View RelatedI'm having some problems with a D-Link switch. I believe it's filtering the management VLAN frames, which is really strange. If you look at the graph, you can see that the D-Link is connected to three switches by trunk links. I'll just use the numbers set in red on the graph to explain what's going on, it's simpler to see.So when I'm connected either to switch 4 or switch 5 (or the others on 5's level) I can use the management VLAN (ID = 1) to connect to all switches above number 3 (including number 3) but I can't get to switches numbers 1 and 2.The only way to connect to those switches is to either connect directly to one of their ports attributed to VLAN 1 or by connecting directly to switch 3. So that's why I concluded that switch 3 filters VLAN 1 frames. It's not switch 4 cause I can get from 5 to 3. But at 3, the frames stop.Also, this only happens for VLAN 1. We have some VoIP phones connected to switches 1 and 2 and their frames can communicate anywhere in the network.
View 12 Replies View RelatedI have a L3 core switch with multiple VLANs setup. Is there a way to place an IPS so as to monitor the traffic passing between, lets say, VLANS 1-3 and VLANs 4-10?
View 19 Replies View RelatedI am trying to set up a VLAN on my Netgear switch (GS105E). I want to create two separate networks and I want both of them have internet access.
I have configured port 1 and port 5 as vlan1 and port 2 to port 4 as vlan2. I plugged a cable from the router to port 5, and the computer on port 1 has internet access. However, the computers on port 2 to port 4 have no internet access.I had tried to create VLANs with the router but had no luck.