I have a school running at the factory network and I was forced to find another ISP just for the school. How can I configure the router/VLAN to have the school in both factory network for exchange server and File server & and the second ISP just for internet.
View 1 RepliesI would like to configure a 3750 switch port to be able to use two vlans. I know you can do this with a voice and data vlan, but what about two data vlans ? Say I have two devices, one on a 10 subnet and the other on a 172 subnet, but i only have one wall jack for both devices to plug into. So I use a mini switch to connect both devices and connect the switch to the wall jack; and of course this all leads back to one switch port. When I go to enter the switchport access vlan 172 cmd, how would I also make it so the device on the 10 subnet could route out ?
View 9 Replies View RelatedCan you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
I can get to anywhere I want on the web except one IP, and I can't ping it either. What can cause this? (Security off)...
View 6 Replies View RelatedAm trying to understand how we can have multiple IP addresses on a single NIC and what are the restrictions on the same. If i can have two IPs from two different networks present on a single NIC, then why would i ever get a new NIC?
Also, i want to understand the concept of virtual IP and how it fits into this picture.
I have an older DELL power edge 2800. Currently we have 2 NIC's one for the WAN one for the LAN. I wish to increase my users access speed. Can I team and or bond up to Four NIC's on the LAN side and leave the single NIC for the WAN? I am having trouble finding any info on the net for pulling this off. I have 67 users and throughput is getting a little rough.
View 1 Replies View Relatedi have two LAN 1:=IP10.44.0.76 subnet:255.255.255.0 & gateway: 10.44.0.1 ; 2:=IP DHCP,i want to do work both network. how can its possible.
View 3 Replies View RelatedIs it normal for a pc to send broadcast to ip address that don't really exist? I am using wireshark to sniff my company's network activity and im seeing something like this.who has 192.168.2.102 tell 192.168.2.235
who has 192.168.2.103 tell 192.168.2.235
who has 192.168.2.104 tell 192.168.2.235
who has 192.168.2.105 tell 192.168.2.235
who has 192.168.2.106 tell 192.168.2.235
but ip address 192.168.2.102 - 192.168.2.106 are currently not being in use..
I heard about this little indy game called "Kerbal Space Program" and tried out the demo and loved it.I decided to shoot 'em $15 to support their efforts; this also gets me the "full" or I should say "most current" version.After getting the confirmation emails from paypal, I'm off to their webpage to download...now remember, I'd been on their website all day."Problem loading page", and "Connection timed out!" etc etc.I tried my usual troubleshooting methods of pings, tracerts, and direct IP address connecting, all with the same results.I then went to online chat with my ISP, Comcast.The tech told me with basic things I knew wouldn't work, but I humored him...Then he decided he'd try a few "remote connection resets"...on the second time my connection crapped out completely. After restarting my PC and doing a complete cycle of both my router and cable modem, I got back "online"...but not really. Any address I put in auto-sent me to the "Comcast sign-up page"...well I got this resolved after 2 hours on the phone with Comcast, but I'm still disturbed that whatever that technician did while I was in support chat with him effectively DELETED my internet service (I looked at my account from my cell phone and it had NO SERVICES listed at one point!). [code]
View 4 Replies View RelatedSorry, I realized that this should have been under web and email...not networking so I moved it there.
View 1 Replies View RelatedFor the past few days now, I haven't been able to connect to a single website. The website in question is [URL] I've tried everything that I can think of, but nothing is working.
I've tried multiple browsers (Chrome, Firefox, and IE), I've checked my host file and I've flushed my dns, restarted router and computer, and renewed/released the ipconfig. I can ping the website in CMD and all the packets go through fine, but attempting to connect via domain name or IP address with a browser does not work. Using a proxy also does not work. Connecting to my neighbors wifi does work.
Sometimes If I let it sit there and load for a long time, it will connect but only partially load the page. I'm also able to connect to the websites chat network and stay connected even while the rest of the site will not load.
I'm guessing it has something to do with my router. I have a westell router/modem which I'm pretty sure the firmware has been gimped by my ISP, Century Link.
i have one xp machine. i wnd to configure two different dial up connection in one xp machine for band width sharing.
View 1 Replies View RelatedI want to setup a virtual LAN setting in a single machine, whats the procedure?
View 1 Replies View Related
I've 4 ISP in my office. In my network all the machines are connected through unmanaged switches.Now if I need to shift any one machine to other ISP then I need to change his IP.Is the following possible:
I connect all the four ISP's to a machine(say Server), then I take out a wire and connect it to the switch so that I can distribute all the ISP into the network.Now on the basis of the MAC Address I can change the assign any ISP to any of the other machine in the network.Also is it possible that I can monitor their data usage as well as can CAP there bandwidth.
I need to put a few cameras, without a server, on a static WAN ip address. Do I just assign them a static LAN ip address(for example 192.168.1.200), make sure the port they use is open, then type the WAN static ip address then colon and the last address? Like this.....I'm making up the WAN address....45.34.55.334:200
View 1 Replies View RelatedI have two computers but only one of them has Hard Disk.I want to run both computers on that single Hard Disk by ntworking.
View 1 Replies View Relatedi have a wifi laptop. Is it possible with a router to connect to my bb wirelessly without using a host pc?
View 3 Replies View RelatedI'm looking to implement a single proxy server for two different VLANs. Both VLAN have outgoing traffic configured through different ISP i.e. traffic for users on VLAN1 is routed through ISP1 and traffic for users on VLAN2 is routed through ISP2. Inter-VLAN communication is enabled. The proxy server should route internet traffic for users in VLAN1 through ISP1 and for users in VLAN2 traffic should be routed through ISP2.
View 6 Replies View RelatedMy brother is using an insane amount of bandwidth, and being from Australia, we don't get very much unless we want to pay very much
View 5 Replies View RelatedI have some technical consultations that I would like to know which would be a better implementation.
I am seeking for clarifications whether putting VPN and firewall in a single software or separating both into separate software.
some of the servers are not pinging from one switch but they are pingable from other redundant distribution switch. So I took the IP addresses from the redundant switch, with that I found MAC addresses from the access switch.But when I tried to see to which ports these MAC are addresses are connected to, multiple MAC addresses are resolving to the same switchport. like 5 MAC's are showing to 1 port and other 3 MAC's are showing to other port, like this there are many. All these MAC's belong to virtual servers.
View 11 Replies View Relatedhow to connect 5 pc with single 3g modem i have router & switch
View 2 Replies View Relatedsir i have my router and i want to restrict it to my personal pc.
View 3 Replies View RelatedCan I connect two routers on a single internet modem. I need a router that is isolated from a public wi-fi connection. The routers need to operate independently.
View 2 Replies View RelatedI have two usb modem A and modem B. modem A could download at max of 300kbps while B could download at max of 700kbps. Since I am a frequent internet user, Im planning to use this two modem simultaneously so that I could have a max speed of 500+300=800+kbps. But I dont know if this would work. The problem with usb modem is that, when you connect the modem A in the internet while modem B is currently running, Modem B is being disregarded right? I was thinking of, say while im browsing and downloading, modem A would be use for browsing and modem B is for downloading. Or them may either share each connection for better performance.
View 1 Replies View RelatedI have a phone line and am using a adsl 2+ router for my pc. Now I wish to install a new Tp-link adsl 2+ wireless router for my lap which is used upstairs. and I wish to connect this wireless router to the same phone line with another splitter.
View 1 Replies View Relatedi am taking care of computer lab having 30 computer in it .all connected in lan with server.is it possible for me to switch off network or say internet for any single computer.(any software or anything)
View 2 Replies View RelatedHow to set a priority signal in single SSD ID in wifi ?
View 1 Replies View Relatedi have configured my network like below:
I have three lan ports in my server the IP is:
(1) IP: 10.10.10.2 SUBNET: 255.255.255.224
(2) IP: 10.10.10.34 SUBNET: 255.255.255.224
(3) IP: 10.10.10.69 SUBNET: 255.255.255.224
I have given IP as mentioned below to 1 to 30 pc connected in First Switch.
IP Starts From : 10.10.10.5 To IP : 10.10.10.30
Subnet Mask: 255.255.255.224
Gateway: 10.10.10.2
For 31 to 50 Pc in Second Switch
IP Starts From : 10.10.10.40 To IP : 10.10.10.65
Subnet Mask: 255.255.255.224
Gateway: 10.10.10.34
IP Starts From : 10.10.10.74 To IP : 10.10.10.85
Subnet Mask: 255.255.255.224
Gateway: 10.10.10.69
Pc are connected internally in separate switch. but can not connect all three switches & with server. Only Gateway 10.10.10.69 is connected with server.
how to connect a different ip addressing single system in different place. but we cann't change the ip address in manually
View 1 Replies View RelatedI've got two houses about 5 miles apart anyway the phone co let me have an off premesis extention at no extra charge two phones that use the same number in the two locations they said i can use my dsl at the other location but i would have to use the same modem/router at both locations iam pretty sure i cant use the dsl at both locations at once but is there a way i can set up two routers on the same phone line where i dont have to carry modem/router back and forth.
View 1 Replies View RelatedQuestion: how would STP or RSTP behave in a star topology with a hub in the middle?i.e. you have four switches all linked to the same central hub. Single links, no loops.Each switch would then get BPDUs from everybody.Going by theory, it should be OK since it still sees the root's BPDU and will see the link to the hub as the root port, despite presence of other BPDUs from other switches? No different from receiving an inferior BPDU from an upstream switch and a superior BPDU from a further upstream root switch.I guess I could lab it by turning off spanning tree on a switch to simulate a hub? I've never previously had to deal with STP issues where there are hubs that aren't strictly point to point bridging so to speak (ok they're not bridging but you get the drift).I've got a scenario I'm examining at the moment where this is the topology, except all switches have bpdufilter running hence effectively no spanning tree. I'm curious to know what would happen should I remove the bpdufilter.I realise there is zero benefit in spanning tree in this instance as I don't have any redundant loops to fall back on, but I'm reluctant to turn off STP on those vlans (since obviously theres stuff behind those switches). The BPDUfilter method seems like an elegant solution but I wonder if its actually necessary.(the hub is actually a VPLS mesh, most sites terminate PE to CE router but I'm playing around with switches as the termination points – run our own Q in Q, split vlans off before it gets to layer 3 as separation, etc.)
View 1 Replies View RelatedI just want to keep one PC as a server and one switch connect to it (For LAN). I want to connect multiple client/screen to that server, so I can use single servers for multiple screen/client.(Client machine will not have any CPU, they will utilize servers memory.)
View 1 Replies View Related