My host has an IP of 20.168.1.2 from a router DHCP. I have a virtual environment which has a DC and DNS and the IP is: 192.168.1.x how can I get access from my host to the virtual environment? What do I need to setup on the host OS? (Windows)
View 3 RepliesI have installed an Oracle DB (11.2) on a guest VM (Centos 5) and my host is Windows 7 Ultimate.I need to able to connect to the DB from windows.Ping status is as follows:
guest -> host - IP : Yes
guest -> host - hostname : Yes
guest -> guest - hostname : Yes
guest -> guest - IP : Yes
[code]....
VIRTUAL MACHINE ~ Can Guest OS become Infected Through Host OS ?If I setup and use a virtual machine running/containing both a Host OS and a guest OS ... do they remain completely separate entities when operating one or the other?My main concern is Virus related ... if for instance I'm Running Windows 7 as the host and XP as the guest and I get the host OS infected, will the guest XP OS also contract it by default because it is operating on the same disk?
View 1 Replies View RelatedWhat are the most common cause for a "could not connect to host" problem?The firewall is not blocking anything, and even with the firewall disabled, the problem still occurs. With "Server" service turned on, the problem still happens.Windows xplso the server couldn't find any trace of a connection attempt, so my attempts to connect never actually made it to the server.
View 5 Replies View RelatedI'm just wondering if its possible to ping an IPv4 host using the IPv6 host assuming that the NAT64 has already been implemented?
[code]...
I have a host that can successfully connect to a PIX 515E (7.x OS) via VPN Client; however, I have no IP routing to the LAN from the remote host.The VPN IP pool works finem,The LAN default gateway is the inside interface on the PIX; the network is flat L2 behind it.The default route on the PIX points out; no other routes are defined,The VPN remote host can be pinged from LAN hosts, but the VPN remote host cannot ping any LAN host, not even the PIX inside interface.
View 2 Replies View RelatedASA 5510
Ver 8.2(5)
I have been looking all over the place for the answer of how to allow clients on an IPSEC VPN to ping from host to host.
How is it possible to connect a host to a switch when they're in different subnets? I'm new to Networking and was thinking it may be achievable through VLAN configuration?
View 3 Replies View RelatedI've got an 1841 router acting as the firewall for a LAN. It also does NAT and acts as the dialer for a PPPoE DSL line to the internet.
All is working fine, except now I need to allow a Tivo device to connect to certain ports on the Tivo servers on the internet. I want only the Tivo to be able to do this. The problem is that NAT is happening before my outbound ACL is checked, so even though I've got rules to allow the Tivo's LAN address out on all ports, it never works. I've verified this using a syslog server, and can see my external DSL IP trying to connect to the Tivo servers and being denied.
I've done things like this at work by NATting the appropriate internal host to its own external static IP address, which allows me to write rules allowing only that external address to do stuff. But I don't have multiple external addresses to work with here.
I tried applying my outbound ACL to the LAN interface of the router in the "in" direction (and removing the same ACL from the Dialer interface in the "out" direction), but that broke other things like the router's own ability to ping out to the LAN or to see a TFTP server on the LAN. I could maybe fix all of that with rule changes and inspect statements on traffic going out toward the LAN (not sure of this, think so), but I'm wondering:
Is there a better way to let just the Tivo makes outgoing connections to certain ports?
Config pasted below:
!
! Last configuration change at 17:15:10 CDT Sun Jul 15 2012
! NVRAM config last updated at 16:27:14 CDT Sun Jul 15 2012 by someguy
!
[Code].....
My internet connection started to disconnect after an office mate used my PC. I thought it was just the cables but it's not. I pinged my ip address and its okay (sent=4; received=4). But when i ping Yahoo! and other websites, it said that "Destination host unreachable" (sent=4;received=0;lost=4;100% loss). What should I do to make my connection okay? I didn't ask assistance from our IT personnel bcoz they said if i want to reconnect/reinstall connection, I have to get an approved request from our bosses. And I don't like being asked bcoz they are like tyrant bosses.
View 2 Replies View RelatedWhen I try to ping ipv6.xsnews.nl on either of my Windows 7 computers, it returns "Ping request could not find host". But when I do it on XP, it succeeds. I have tried putting the W7 PC in the DMZ, disabling the software firewall but it doesn't work.
What I think it involves is having ipv6 installed on each. I tried to duplicate the setup of both the XP and a W7 computer, installing the gogo6 tunnel. But apparently it's not setup on this computer because the ping result is the same as on the third computer which hasn't had ipv6 installed. s not setup on this computer because the ping result is the same as on the third computer which hasn
Small office setup with a wireless modem/router. We have two computers that are identical HP Pavilion a6807c PCs running Vista Home Premium. Other computers in the office are a bit older and run either XP or Vista.Just purchased a new HP Officejet 7000 printer and connected it via a USB to one of the HP Pavilion Vista computers (which I will refer to as HP1). The printer works fine on HP1 using the direct USB connection.Set printer sharing, file sharing, and even public sharing on both HP computers (HP1 and the other one I will refer to as HP2). Workgroup name is the same. Can access HP1 and see the HP printer on HP1 from other computers in the office. However, when I try to connect to the printer from HP2 to HP1, it locks up HP1 and HP1 requires a hard reset. I tried installing the software/drivers on HP2, but HP2 still tries to install the drivers from HP1.I am not sure its a problem with HP1 as much as it is a Vista issue. The reason I say this is because I have been able to successfully use an XP computer (XP3) to connect and print to the Officejet on HP1.
View 1 Replies View RelatedWe have an ASA5510 with the IPS ASA-SSM-10 module installed. All is working well except event notification. When sending a test email from the SSM IPS, we get the error "could not connect to SMTP host". The Exchange SMTP host does allow traffic from the IPS and ASA. I can ping to the SMTP host by IP and name. What am I missing here?
View 3 Replies View RelatedI have created a RA VPN with a 5505 using Anyconnect client. My VPN functions perfectly, but now I am trying to limit access so that only one single host on my network can connect. To do this I tried creating an ACL permiting the host and denying all other traffic, but it does not work it seems every one can connect. how I can limit the outside access to a single host?
View 3 Replies View RelatedWe are using an ASA with 8.4 in transparent mode. Connection fails when a host on inside tries to connect to a server on outside. This server uses mac-address 0100.5E00.0000 to load balance but replies with real mac-address.Firewall logs "Deny TCP".ARP inspection is disabled.
View 2 Replies View RelatedI have a host machine (Laptop, Win 7 Home Premium x64) running Windows 7 Ultimate x64 on VMWare Workstation 9. I've got this system set up for UMDF driver development, because I need a target machine to debug drivers on. However, because I'm developing drivers for Win 7 (x86 and x64), I cannot connect to the virtual machine on via a simple network connection. Connection methods are outlined here.
I have tried a few different pieces of software (mostly Eltima software), and have Google'd every combination of phrases that I can think of. I can't find any information on this anywhere. I don't just need to share data between the machines, I need a more "physical" connection.
Does any know how to do this, or if there's another (preferably more simple) way of doing it?
Any problems with the guest network on the ea4500 with the cloud firmware? I am losing guest clients after about 24 hours and the re-authentication fails. you enter the guest password and nothing happens until you reboot the router.
View 2 Replies View RelatedThe Lg840g is a tracfone with wifi capability. I get strong wifi signal and connection at home, but receive failure to connect to requested host message when I open the browser. This phone works at wayport wifi, so I assume it's a compatibility problem with the router. Is there a fix? (Router works great with our Acer and Kindle tablets though.)
View 1 Replies View RelatedI purchased a WNDR3400v2 probably around two months back and since then I haven't had any issues with it. Now, I like to keep the security setting on WPA2-PSK for the security but my brothers and my own Nintendo DS don't support this security for connecting. So, since my previous router had a guest network, I decided to activate and deactivate that network with no security when it was needed (Half hour or less), and I haven't had any issues until doing this with the WNDR3400v2.
Basically what happens is, after disabling the guest network again, no wireless devices can connect to the router... PERIOD... Upon trying to connect it also says "You are unable to connect) right after it verifies the password. I spent a few hours trying to fix it but I haven't gotten anywhere really..
What I have tried-v
-Resetting the Router
-Powercycling the Router
-Resetting it to factory defaults and restoring previous settings
-Enabling and disabling the network
-Deleting the original network saved on the computers and connecting as if from a new network.
-Also tried restarting my computers
-Updating the firmware (For some odd reason I couldn't find any firmware last week..)
I researched it a bit and found some solid leads, but nothing that fixed the issue. The only "Fix" I could find was disabling the security and leaving it open.. Which I would prefer not to do for obvious reasons...
Router Type: Netgear Wireless Dual-Band N600 Router (WNDR3400v2)
Firmware: V1.0.0.34_1.0.52
My EA4500 has the newest firmware and is properly configured to support 20+ wireless and wired devices. It does this job well.Guest Access, however, is a problem. It works for about a day, then stops.Guests can access the login screen and enter the password. Then nothing happens. The screen appears to "load", but it does not connect.I have tried returning to default settings and reconfiguring and reupdating firmware. I have tried turning Guest Access on and off, as well as resetting the password.The only that works is rebooting the router. This is obviously not practical, especially for a contract client.
View 4 Replies View RelatedI have an E2000 setup with the Cisco Connect Utility. I have a MAIN account and a GUEST account setup.I'm recently having a problem where I can only connect wireless through the "Guest" account. I can connect to my MAIN account, but it states that I have "Limited Access".
View 9 Replies View RelatedGuestconnect SSID configured on 5508 WLC with Pass through athentication (NAC guest server). No issue with Laptops and Iphone/Ipad ver 4and 5. Only Iphone Ver 6 users unable to access Guest connect .
View 9 Replies View RelatedWe have been unable to connect our PSPs to the new E2000, and after several hours we're ready to throw in the towel and go get a different router!The PSPs only see the "guest" connection when using the scan option, but cannot connect to it. Even after manually adding both the main and the guest info we are STILL unable to connect either of the PSPs We had an older router from your company which we had no issues connecting 6 desktops, a lappy, 2 psp, 2 ds, 2 xbox 360, and a Wii, as well as our smart phones. After this recent "upgrade" to the E2000 the PSPs CANNOT connect no matter what we do. It gives many different error messages.
View 9 Replies View RelatedHow do I add a guest without the cisco connect software since they don't have upgrade for osx lion.
View 3 Replies View RelatedI just bought a E1000 and connected it to my cable modem. I can connect to the internet with my wired PC and wired Xbox 360 with no problems. For some reason on my wireless laptop I can only connect to the internet by the Guest connection. When I connect to the regular router SSID I get local only access, no internet.
View 2 Replies View RelatedIs it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies View RelatedI want to prevent guest from doing peer - peer communication on my Guest (5508) controllers. Is this a feature on the WLC or only by applying an ACL on the router interface?
View 2 Replies View RelatedAndroid users can connect to our hospital guest wireless but will not have connectivity. Our wireless infrastructure is WISM based with 2 controllers on 6509 platform. We have a mixed environment of 1231, 1252 & 3502 series APs.
Had issue connecting just Android devices? All other devices connect fine.
Ive been going over some exam questions and i got a question regarding diskless host. i have dont some googling but cannot find a overview explanation.
View 4 Replies View RelatedI am trying to find a way to find the netid and hostid of any given ip address, given any ip address, I know the left side the IP address is the netid and the right side of the ip address is the host id but I am pretty sure there is more to it than that.
View 1 Replies View RelatedAny service where a computer can host a website just about anywhere with an internet connection? As in... using the VPN as the connection so that no router port forwarding is needed?
View 3 Replies View RelatedThere are anonymous VPN services that let you hide your real IP address from the websites you visit.But can you host an HTTPS website from behind a VPN so that nobody knows your real IP address?
View 1 Replies View Relatedfind host by MAC Address
View 1 Replies View Related