What Is Diskless Host
Jul 6, 2011Ive been going over some exam questions and i got a question regarding diskless host. i have dont some googling but cannot find a overview explanation.
View 4 Replies
ADVERTISEMENT
Servers :: What Is A Diskless Station In Bootup
Mar 10, 2011what is a diskless station in networking
View 1 Replies View RelatedPXEiSCSI Diskless Booting Using CCBoot?
Nov 9, 2012Currently working on a personal project to diskless boot several PCs of different configurations. Trying to use software called CCBoot only because it seams to be the easiest way of uploading the disk images to the server. My problem is that when booting the test machine it will not load from the TFTP server (times out).168.0.2 and is on a network with a Cradlepoint MBR95 router which provides DHCP. The server handles one of my ISPs and the router the other, but I don't think that will be a problem. CCBoot support highly recommends I use the software for my DHCP, but can use an existing DHCP server[CODE]
View 2 Replies View RelatedCan Pure IPv6 Host Ping A IPv4 Host?
Feb 10, 2011I'm just wondering if its possible to ping an IPv4 host using the IPv6 host assuming that the NAT64 has already been implemented?
[code]...
Cisco VPN :: Pix 515e - Remote Host Cannot Ping Any LAN Host
Jun 27, 2011I have a host that can successfully connect to a PIX 515E (7.x OS) via VPN Client; however, I have no IP routing to the LAN from the remote host.The VPN IP pool works finem,The LAN default gateway is the inside interface on the PIX; the network is flat L2 behind it.The default route on the PIX points out; no other routes are defined,The VPN remote host can be pinged from LAN hosts, but the VPN remote host cannot ping any LAN host, not even the PIX inside interface.
View 2 Replies View RelatedCisco VPN :: ASA 5510 Ping / Communication Host To Host
May 7, 2012ASA 5510
Ver 8.2(5)
I have been looking all over the place for the answer of how to allow clients on an IPSEC VPN to ping from host to host.
Net And Host ID Of Any Given Ip Address
Jan 16, 2012I am trying to find a way to find the netid and hostid of any given ip address, given any ip address, I know the left side the IP address is the netid and the right side of the ip address is the host id but I am pretty sure there is more to it than that.
View 1 Replies View RelatedCould Not Connect To Host?
Mar 24, 2011What are the most common cause for a "could not connect to host" problem?The firewall is not blocking anything, and even with the firewall disabled, the problem still occurs. With "Server" service turned on, the problem still happens.Windows xplso the server couldn't find any trace of a connection attempt, so my attempts to connect never actually made it to the server.
View 5 Replies View RelatedHost Website Anywhere Using VPN
Nov 2, 2012Any service where a computer can host a website just about anywhere with an internet connection? As in... using the VPN as the connection so that no router port forwarding is needed?
View 3 Replies View RelatedHost HTTPS Website Over VPN?
Jul 7, 2011There are anonymous VPN services that let you hide your real IP address from the websites you visit.But can you host an HTTPS website from behind a VPN so that nobody knows your real IP address?
View 1 Replies View RelatedFind Host By MAC Address?
May 12, 2012find host by MAC Address
View 1 Replies View RelatedCisco :: ACL To Block One Host From Another?
Oct 31, 2012I am learning to write ACL's along with a billion other Cisco things. The internet is not clear on how to do this exactly. At least in my research.
I have two host on the same subnet and I want to block all except RDP TCP port 3389 from one host to another.
I want to apply that Access-group to a switchport interface on my 3750 that belongs to the computer I want to protect from the other.
Host A: 10.1.1.10/24 -- I need to block all TCP and UDP traffic except for port 3389tcp
Host B: 10.1.1.60/24 -- I need to allow only TCP port 3389 from Host A to this one.
This is on the same switch so I can use an extended ACL like 101 or whatever.
This is almost starting to make sense to me but im still weak on extended ACL. I got basics down pretty well.
Ping From Host To Guest With NAT?
Jun 27, 2012I have installed an Oracle DB (11.2) on a guest VM (Centos 5) and my host is Windows 7 Ultimate.I need to able to connect to the DB from windows.Ping status is as follows:
guest -> host - IP : Yes
guest -> host - hostname : Yes
guest -> guest - hostname : Yes
guest -> guest - IP : Yes
[code]....
Downloading And Using Host Files
Dec 3, 2011I downloaded the HOSTS file from winhelp2002.mvps.org, hoping it would better my security. However, now some pictures that used to show either show the "Internet Explorer cannot display the webpage." or just have the X box thing. I'm guessing this problem results from the new HOSTS file. What should I do? Should I revert to my old file? If so, then how can I do this?
View 4 Replies View RelatedRDP Without VGA Driver On Host Machine?
Jul 8, 2012Basically, I am swapping my Atom/ION nettop (that I use as a file server, game server, torrent server etc. etc.) for one that has no fans and no mechanical HDD. I control it primarily via RDP, so I don't need to plug a keyboard or display into the nettop itself.
The new one I'm getting should be a step up due to the whole no moving parts thing, as well as the much faster CPU. But Intel, in their infinite wisdom, have not provided (and don't plan on providing) a 64bit graphics driver for the GMA 3650.
If I were to install 64bit Windows on this new machine without installing a driver for the graphics, would I have any issues using RDP? I'm not sure if the visuals are generated on the host or the client and whether it would matter either way.
Host Names For NAS And Xbox 360
Sep 17, 2011Is it possible to give me NAS and Xbox 360 Host names so that they show up in my DHCP Client list? Currently there are 13 devices connected, 11 of which have a host name but these two do not. It also shows the IP and MAC addresses of each connected device.I just want to make sure that all of the devices that are connected are what I would expect.
View 1 Replies View RelatedConnect From Host To Guest?
Apr 28, 2012My host has an IP of 20.168.1.2 from a router DHCP. I have a virtual environment which has a DC and DNS and the IP is: 192.168.1.x how can I get access from my host to the virtual environment? What do I need to setup on the host OS? (Windows)
View 3 Replies View RelatedCan't Host Minecraft Server
Feb 22, 2013I have this Minecraft Server hosted at TCP 25565.I don't use any router and is connected to an RG-Box directly.My Firewall is disabled and so is Avast!But still nobody can connect from anywhere. I gave them my external IP and nothing worked out.I did a "netstat -a" search, and yes, I do have a connection listening at this port TCP.Still, I get this "Connection timed out: Connect" error when trying to reach my server from anywhere out side of my network.I called my ISP regarding this problem, and they told me that they were only blocking port 24 and 25, all other ports is free to use. And they told me that I don't need to Port-Forward or anything, I just plug my computer directly into the RG-BOX, and I should be good to go. But I'm not.
View 4 Replies View RelatedHost Names And IP Addresses?
Sep 30, 2011I have been asked to do is locate some computers on the network and run a security scan on them. Well i pinged the host name and got an IP address. Then the network admin me look up the switch port that the computer is located on and so on. So i find 3 of the computers im looking for and when i get on the computer and look up the name but it does not match the name given to me. So i do an ipconfig /all and see that the computer has the right IP address and MAC address but not the same name. So my main question is, are these computers one in the same or is something messed up?
View 1 Replies View RelatedCan't See Shared Host's Name On Windows 7
Oct 16, 2011I have 3 computers connected to the same home network. i name them XP1, XP2, and win7. obvious from the names, two pcs are running xp and one is running win7. I shared all three in the network. XP1 uses static local ip while XP2 and win7 use dynamic local ip. on xp2 and win7, i could not see XP1's hostname on neither xp2's my network place, nor win7's network. However, i could access xp1 over using its static IP. what xp1's hostname is not shown on the other two's network places? is that because of xp1 is using local static ip?
View 6 Replies View RelatedCisco WAN :: 871 Can't Ping From Host
Jun 30, 2012I'm going through the CCNA training and I'm setting up my DHCP server on my 871 router. I have my cable modem into the WAN port on my router and have 1 host plugged directly into Fastethernet 1. I can ping any IP I want from the IOS prompt but I only have local access from the host. [code]
View 4 Replies View RelatedGathering Host File Entries?
Sep 9, 2012I work in a service desk in +100 company and lately i got a task to gather all the host file entries that are on our network's PC's.We operate on windows XP 32&64bit, W7 64bit. Is there any tool that i could use to scan all host files within our network. I tried google of course but maybe i type my search phrases in a bad way to find something useful to my needs.
View 4 Replies View RelatedCisco :: Can't Ping From Outside To The (online Host) PC
Aug 26, 2012I tried to ping from the "online host" PC to the outside,it succeeded. However, I can't ping from outside to the "online host" PC.
View 2 Replies View RelatedDetermine If A Switch Is Between A Host And A Target?
Nov 23, 2011I was attempting to troubleshoot a logon problem with some machines, when it was finally revealed that there was a managed switch between the host and the target preventing this.
How would I detect this in the future? (A tracert showed nothing between host and target.) Would Wireshark show me this info, with reduced TTLs?
getting a picture of all devices between a host and a target?
Host Names Do Not Resolve With Right IP Address
Nov 30, 2011where the host names do not properly resolve with the right ip address.Example, I ping a host name, it gives me an IP, but when I VNC into the workstation, it is a totally different host.
Adding DNS Without Modifying The Host File
Jan 19, 2012Windows 7 OS
I can ping and connect to servers by IP address from my workstation. However, Sys Admin wants everyone to use the DNS name instead. The only way I know to add DNS names is to modify the host file on the workstation. Sys Admin has forbidden users from modifying their host files.
How else can I map these IP addresses to DNS on a Windows 7 machine?
I have tried modifying the domain, thinking I can use the DNS entries on the domain server. Did not work. If this should be working maybe I'm not using the right domain? Any way to determine what domain to use?
I am decent in using command line, feel free to give non-GUI based answers.
Notes:
- I do know how to modify host files, including the Windows 7 work-around for having this locked out. But it's a "rule" by the Sys Admin not to do it. So I'm trying to adhere to the policy
- Sadly, asking the Sys Admin for the alternative tactic is not an option. Lame but true.
- I have scoured the internet for info on this issue. Everything I find either involves modifying files or enabling services on the server, or modifying the host file on the workstation. Even looking at the server settings is out (I don't have access).
Cisco :: How To Locate APIPA Host
Jan 25, 2013I'm receiving a lot of logs on my FW about host cannot receive correct IP address and get APIPA addresses (169.254.x.x).
Is there a way to locate them on network? From my core switch i cannot see them
Cisco :: Can't Ping From ASA To Host In GNS3
Apr 24, 2012I test all devices using ping command, from ASA to router was fine (on both interface) but not to Host , and host to router was fine, but only on directly interface(F1/0), and to ASA was not success. am i miss something in my configuration?
View 5 Replies View RelatedHow To Create A Domain Host Controller For Xp
Apr 11, 2012o create a domain host
View 2 Replies View RelatedCisco :: Can't Ping From Inside To Outside Host?
Jul 6, 2011configure my Cisco ASA5510 (asa version 8.3.1) so that one of the host (e.g.192.168.8.20) behind management interface can ping to the other host (e.g. 192.168.2.246) behind OUTSIDEinterface. I tried modifying the ACLs, NATs and ICMP statement, but still failed[CODE]
View 19 Replies View RelatedVirtual PC Using Different Internet Connection Then Host?
Feb 2, 2011Running a Windows 7 laptop plugged into a LAN using ethernet cable with internet.The built-in wireless nic on the laptop connects to a totally different internet network. I set up an XP Mode Virtual PC on the laptop with the intention that it would use the wireless internet connection.I set this up by installing Microsoft Loopback Adapter, then sharing the wireless nic to it. The Virtual PC is set to use the Microsoft Loopback Adapter as its network connection.My problem is that only the hard wired internet connection works.The wireless is connected and has an ip address, however no traffic flows through it until i either disable the cabled network or physcially unplug the cable. Is it possible to have my host laptop use the cabled internet connection and my virtual pc use the 2nd wireless internet?
View 1 Replies View RelatedConnect Host To Switch In Different Subnets?
Jul 28, 2012How is it possible to connect a host to a switch when they're in different subnets? I'm new to Networking and was thinking it may be achievable through VLAN configuration?
View 3 Replies View RelatedCreate A Network Between VMware And Host OS?
Jan 6, 2013how do i create network b/t vm ware and host machine ?
View 1 Replies View Related
