D-Link DIR-601 :: Can't Gain Access To Router
Dec 24, 2012
I bought this router from a rummage sale, and it works great. The only problem is, I cannot access it to set up a password. I have downloaded the manual, and tried the troubleshooting. I disabled the firewall, did the reset button on the back of the router, but all I keep getting is "The Connection Has Timed Out" error message. I also went to the emulator site, but it said that there was no support any longer for that model. I have tried this on both Internet Explorer and Firefox. I personally have Windows 7, and on Comcast.
View 4 Replies
ADVERTISEMENT
Apr 10, 2013
Just got my Linksys EA4500 router today.The only confusing thing, not not well explained by Linksys . Is the USB storage set up.One thing (very important) Linksys has failed to explain how to gain access to the USB storage once connected to the router. Once the USB storage drive it set up. Or at least I think it's set up. Nothing shows up on my network page. So how am I to get access to the drive? If it don't show up?I need to know how to gain access to the USB storage drive that is connected to the Linksys router.
This is how I think it is to be set up. Again the instructions are not all that clear how to set up. And where is this widget on the homepage to be located?
View 4 Replies
View Related
Sep 25, 2011
connectig two computers into one modem
View 2 Replies
View Related
Dec 15, 2011
got problems connecting to any internet connection on a lenovo G555 laptop with a atheros AR9285 wireless network adapter. Can access all the connections with a different laptop but not my lenovo so I know it is not a problem with the routers.Tried doing a system restore, tried disabling the network device then re-enabling it, tried switching the wireless on and off as well as restarting the laptop but no luck.
View 1 Replies
View Related
Nov 15, 2012
Normaly all incoming IP addresses can use NAT to gain access. I would like to make a rule that only one IP address can connect to my router and use that port or range of ports defined.
Is there a way to configure a SRP 527W on such a way?
If not possible now, can I expect a software update ?
View 3 Replies
View Related
Jun 18, 2012
I have a Cisco 881 setup with the following VPN config.
[code]...
The client is able to connect just fine to the network via VPN, but I am unable to gain access to any of the local resources. I know 192.168.1.1 has SSH running and 192.168.1.50 has telnet running but if I try to connect to either using the correct program they just timeout. I am really at a loss on why the vpn connection connects but I can not gain access to any of the resources on the VPN network.
View 3 Replies
View Related
Aug 9, 2012
Can a router connect to a switch to gain additional ports (to both access the internet AND to maintain an internal / home network)?IP line to house, connected to modem, connected to 4-port router, connected to 8-port switch. Now, each of six rooms in my house has one Cat-5e (RJ-45) jack whose run terminates to the switch. In some of these rooms, I need two wired devices (wireless isn't an option for the devices). Can I use the LAN port of a spare, wireless router (to also use as an access point for cell phones, etc) to plug into the jack and increase the number of ports in that room to have a functional LAN and WAN? I have read tons of info on plugging switches into routers to increase the number of ports, but not the other way around. Plus, ripping open walls to expand the network isn't feasible either. My other thought, would be to replace the switch with another (2nd) router, by connecting the 1st and 2nd routers together, and have the runs terminate to the open LAN ports of both routers --= and then expand the ports in those rooms by also using additional, spare wireless routers.
View 14 Replies
View Related
May 21, 2013
I recently checked the output of one of my AP 3502AGN which are connected to a WiSM with the current 7.0.240.0 software. There I saw the following output:
show ap config 802.11b 3502AGN-1100c-1
Legacy Tx Beamforming ..................... ENABLED
Antenna Type............................... INTERNAL_ANTENNA
[Code].....
View 3 Replies
View Related
Oct 30, 2012
I am using Xirrus WiFi inspector to survey the signal in y house and I notice a very strong signal at 160dBmMy home signal is in the region of -60 dBm so I am surprised to see such a strong signal at 160I have attached a screen shot so you can see BTOpenzone and BTHomeHub-WM9R with a high power.
View 3 Replies
View Related
Mar 22, 2011
tell me about this antenna
View 4 Replies
View Related
Dec 8, 2010
I am currently working on a project where I need to design a complete wireless solution for a huge building. I performed the wireless rf survey by configuring the wap's to broadcast a SSID and walked around gathering rf coverage data. When configuring the test WAP's i did not join them to a lan controller ( AIR-WLC4402-50-K9 ) but simply created a static ip and ssid to broadcast but modified the internal antenna gain to +128 to change the direction of the broadcast. There are two other ap's already joined to the lan controller on a guest network (configured by another contractor) but when I go into the lan controller web gui I do not see anywhere that allows me to modify antenna gain on the individual WAPs. Also, once the waps join the lan controller they dont seem to be accessible via web. How I can I modify gain per wap?
View 14 Replies
View Related
Jul 7, 2009
What is the impact of incorrectly setting the antenna gain on a the b/g radio of an AP would have on a WLAN?
I've come across a site where around a 3rd of the AP's had their antenna gain set to 0. I can only assume that something missed setting this during setup. The site uses 1242ABG AP's and each has 2 4941 antennas and i believe the gain should be set to 4 x 0.5dBi
View 5 Replies
View Related
Oct 21, 2012
I have just moved into a new apartment that has a free wifi connection the problem is that my apartment is in the basement at the completly opposite side of the office and i cant get a strong enough signal to connect to the internet and im not very good with computers. the first time i tride setting up the repeater i was able to connect everything and get online but it had changed the ssid and when i tride to change it bacck to its origanil name i lost my internet connection and have not been able to get access the internet again.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: AMD Duron(tm) processor, x86 Family 6 Model 8 Stepping 1
Processor Count: 1
RAM: 479 Mb
Graphics Card: S3 Graphics ProSavageDDR (Microsoft Corporation), 32 Mb
Hard Drives: C: Total - 24385 MB, Free - 3678 MB; D: Total - 13776 MB, Free - 13649 MB;
Motherboard: , KM266-8235
Antivirus: None
View 3 Replies
View Related
Nov 12, 2011
what's the difference between High-power and High-gain wireless USB adapters.
View 5 Replies
View Related
Aug 18, 2011
The old router whit revision B2 was replaced under warranty with a new one which has the revision B5. The major problem: I can't access the router from WAN, even if I have the settings as shown below
View 2 Replies
View Related
Dec 22, 2011
I have an DIR-655 router firmware 2.00 Rev.B and from a few days i had some issues with the router.I have some problems with Wi-Fi and share-port and i want to make an upgrade.My wi-fi at some points disconnect me from the router.I mention that i cant access the router through 192.168.0.1 but wired i can.I've downloaded the firmware upgrade but it doesn't work.
View 3 Replies
View Related
Oct 5, 2011
I am using wireless internet via D link router.I am connected to the router but there is no access to the internet.There is a small yellow triangle appearing on the wireless Network icon at the right bottom corner of my laptop.I can browse and download but I am getting the message that no internet access.
View 10 Replies
View Related
Apr 24, 2012
I want to set D-Link DIR 655 as Access Point. For your information , I'm using D-Link 2750U (modem + router) as primary wireless router. how do I set D-Link DIR 655 as Access Point ?
View 5 Replies
View Related
May 28, 2011
I have a D-Link DIR-655 with an usb dongle DWA-140. I used to work with a Sitecom WL-341 router.I want to use the Sitecom WL-341 as an acces point to improve my wireless range at the top floors of my house.
What I want to create:
- The modem connects to the D-Link router;
- The D-Link router makes a wireless connection with the Sitecom router;
- The Sitecom router is now an acces point;
- I connect the Sitecom router with a cable or wireless to my desktop PC.
I don't want a cable in my house that connects the D-Link with the Sitecom. If I do this, not only will people get hurt getting up the stairs because of the cable lying there, it also isn't a pretty sight...
View 1 Replies
View Related
Jun 15, 2013
I've just installed DD-WRT (DD-WRT v24-sp2 build 21676) into my TP-Link (TL-WR1043ND) router. I've setup port forwarding for port 80 to my machine port 80 and it works well under LAN access (checked from my PC and cellphone connected to LAN).
I'm trying to access the testing server from outside through a web proxy, and other sites that check whether my public IP is up, but I can't figure out why I'm unable to access from outside while LAN access is fine.Server is on OS X Mountain Lion with disabled firewall.
I've find it strange to not have an Hairpin NAT issue (I'm able to access the server from LAN through the public WAN address), which is generally a common problem, but still, have this issue.
I've used a web based port scanner and it tells my serving port (9999, not 80) is open (other ports are not), even though I'm unable to browse it.I've learned people can access my server on 9999 port from outside! Now I don't understand why I'm unable to access it with the web proxy tools I've tried.
How can I check, from my machine, that It's serving content correctly, with some online tool or proxy that would access it from outside?
View 2 Replies
View Related
Oct 20, 2011
My router was working just fine when a lightning struck. I cant seem to connect to the router's configuration page (192.168.1.1) anymore, All the lights on the router are on and I tried to reset it to default settings several times but still it wont connect. I tried it on a laptop but I still cant get it to connect. I can surf the net just fine when using the ADSL modem though. I can ping the IPaddress 192.168.1.100 but can't ping the default gateway which is 192.168.1.1. I also tried switching to another cable just in case but to no avail.
Here are some info:
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersMiko Luis>ipconfig/all
[Code].....
View 1 Replies
View Related
Jun 16, 2012
I got a new TP-Link WR740N router and I'm having a problem with it. Everytime I enable security (WEP, WPA etc.) the signal on all notebooks will go "local access only" immediately, even if I use the right password. Router signal is always there, but Internet access will only be available if security is set to "unprotected" on the router setup. Funny thing is that my old router (Linksys WRT54) had WPA2 on and everything was ok.
View 4 Replies
View Related
Jan 7, 2013
I am having a problem in setting up my Router. Its "TP-LINK WR 720N". I have a LAN connection in the main PC and a further dialer like thing with user name and password is executed to access the internet. Each of the customers have diff IDs and passwords based on the bandwidth of the connection. The problem is that first am i connecting the Router in the right way? I put the main LAN cable into the Router's WAN port and the Other Ethernet wire i put is that from PC's Lan port to Router's LAn port. Is this right? I am confused because in the guide a modem is also mentined and i think thats for DSL users...
If i use the above settings, my LAN gets connected and the dialer also works and gets connected but when i access the internet from it, that doesn't work and no webpage opens.
Similarly, the Wireless connetion is displayed in the Laptop and when i access it, it gets connected, but it has a yellow exclamation mark in it, and the same goes here that the internet does not work. My internet connection id fine because i am sing internet no using main Lan ports of Pc, so i guess the problem i s with my Settings...
View 2 Replies
View Related
Jan 3, 2012
I just acquired an Ipod Touch and am trying to set it up to connect to my exisintin DIR-615 router. It is about one year old, but I have misplaced all the info I had on it, including any password info. Trying to use the blue lit button on the right side of the router does not allow access to the Ipod, nor my daughter's Apple computer.
Are there changes I need to make or special procedures for Apple products?
View 1 Replies
View Related
Apr 4, 2012
I have a DIR 655 which I am trying to use as a pure access point for a network based on a Comcast SMC Modem/Router On the DIR 655 I have the DHCP turned off and on the Internet Connection I have given the DIR 655 a static address of 10.1.10.2 with Gateway and Primary DNs 10.1.10.1 (The SMC is 10.1.10.1) I have the DIR 655 connect to the SMC Lan to Lan. DIR 655 is G only to deal with and IPAD issue....
The wireless devices get an internet connection BUT... I can only contact the DIR 655 wirelessly the SMC does not show the DIR 655 as connected I can not ping the DIR-655 from the SMC. I can " see" the static addresses I have given to two network cameras but they don't not respond to Port Forwarding I have assigned at the SMC (that is more for info as I realize that might be a SMC issue) . How to make the DLIK visable to the wired network.
View 14 Replies
View Related
Jul 27, 2012
I've had my DIR 615 router for quite some time. The hardware version is C1, firmware 3.01 originally. It's been fine for the most part (asides from connection issues now and then with the internet - which we rectified by unplugging modem and/or router). A couple nights ago we had a storm and the next morning the router would not connect to the internet. I tried unplugging the router and modem a number of times but could never establish a connection. The internet globe LED was originally orange but after I cut off the power, it never came back on. I tried a number of different cables between the modem and router and could not fix the issue. I bypassed the router totally and the internet works fine. After a lot of failed attempts, I decided to reset the router and reinstall it with the disc. I followed the instructions and kept getting error 322 that the router could not be found. I tried 3 different computers and 5 different wires to fix the problem but to no avail. I kept encountering the same error on each computer. Since the router can't be seen, I must bypass it totally to get any internet access so trying the online setup doesn't work because I can't connect to the router and then to the modem since there is no internet access. So now I'm stuck. I'm not sure if my router is damaged from the storm. All other lights work (LAN and wireless icon) but I can't get any internet access through the router. I'm not sure if I should just go buy another router or not. The installation checks out fine until connecting power to the router and then it can't be found.
I am running windows 7 and vista on different computers and laptops and used setup 4.1.7141.2
View 1 Replies
View Related
Nov 14, 2011
I cannot access my router through IP address or dlinkap. I am trying to connect a bridge for the living room in my house.When I do an IPCONFIG my default gateway as weird characters in front of the actual IP fb23:ff23 etc.
View 4 Replies
View Related
Mar 11, 2013
Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :
I set my TL-MR3020 to AP to act as a repeater to boost my wifi signal in the living.My TL-MR3020 is able to ping the main router but there is no internet access (no Internet light) on the TL-MR3020 . The main router ip is 192.168.1.1 and TL-MR3020 IS 192.168.254.0I followed exactly the instructions on how to configure the TL-MR3020 from TP-Link website and everything seems ok except no internet
View 3 Replies
View Related
Nov 5, 2012
A friend of mine has a network with the following setup: D-Link DSL-2500U for ADSL, connected straight into a Telkom DG834GUv5 (locally rebadged Netgear) which has 2 PCs connected via cable, and 2 laptops via Wireless. A cable runs from the Telkom into a standard IPLink switch, which merely extends a cable into a D-Link DIR-615 running DD-WRT that has 2 computers connected, and shares wireless to a couple laptops.
At the moment the network is somewhat unstable, and recently the Telkom router has been giving serious problems, even after resetting to default. I want to try make the network a bit simpler and more stable. Firstly, I want to remove the IPLink switch, which merely extends the cable. Is an Ethernet Coupler what I need? Both cables are definitely under 100m combined (probably under 50m).
Now the big thing is a replacement for the Telkom (rebadged NetGear). Should I get another D-Link DIR-615 or is there a better solution? Their budget is between $40 and $60 US. Is it best to stick to the same brand, considering both devices are D-Link at present?
View 1 Replies
View Related
Jan 14, 2012
I just bought the 655, mainly for school/Xbox. My parents use it also, but I bought it for myself mainly (shh). I set it up correctly and got connected, but suddenly I wasn't allowed Internet access. The router connects to my laptop, but won't get Internet access. I called customer service and he didn't know what to do. We tried everything he knew and nothing worked. I don't want to return the router cause I read it was very good, but I need internet for school. I have Rev. A and F/W 2.00.
View 8 Replies
View Related
May 21, 2012
I would like to use the web access control that is on the DIR-615 along with my 2Wire modem/wireless router. Is this possible? If not is is possible to put the 2Wire modem into bridge mode and purchase a second wireless modem to run along side the DIR-615 that I have so that I can have two separate wireless networks that have two different web access controls in place?
View 1 Replies
View Related
Aug 6, 2012
Im using d-link 855 router to block internet to certain machines, using access control within dlink and then in putting the ip for the right machines. But it seems the machines keep changing the IP adresses everything they boot thus getting internet access the next day.
View 14 Replies
View Related
Feb 26, 2013
I was trying to access the modem router as the admin but AT&T seems to have a pain in the butt security system from me making any changes. I wanted to forward some ports to setup my Synology DS212j Network Attached Storage (NAS). I connected my d-link router to the already setup modem router which I am now connected to. I have to run off to school but I was wondering, would I be able to forward the port off my d-link DIR-601 and be able to host my NAS server off that?
I don't have too much in-depth networking experience besides setting forwarding ports, setting static IPs, but I can't do that since I am not the admin for the AT&T router. I figure the password for the AT&T router is just defaulted to admin or blank but I haven't had time to fully test everything out.
View 4 Replies
View Related
