I have tried to setup access control by setting up a policy that restricts certain MAC addresses during a period during the day from certain websites. I set up the website filter and a schedule and selected them for the policy. Instead of blocking just the websites on the filter list during the time setup in the schedule, it blocks all websites all the time.I made sure that I setup the policy to 'block some access' NOT 'block all access'.The only thing that seems to work is that only the computers with the MAC address selected are effected.
I'm using my 655 as a WAP, so nothing is connected to the WAN port. Since I run a SBS2008 in my home, I also have the 655's DHCP disabled.If I enable Network Filtering, everything inbound/outbound on the LAN ports works except accessing the Admin page. Even if I put the connecting PC's LAN MAC in the tablet.
I may be doing it incorrectly, but I'm trying to configure web access rules. I first set up access control and tell it to use the website filter. I've tried configuring it by both MAC address and IP address (separately, not simultaneously), but it still allows the listed sites in the web filter to get through. Is there something else I need to block or am I not doing something correctly? The network is on DHCP reservation, so IP addresses are always the same. MAC addresses, as I mentioned, don't work, either and they are fixed and logged in the router.
DIR655 with 1.33NA firmware. I'm trying to determine how to block access to the internet for a specific LAN computer when the user knows how to change a MAC address. I don't want to turn MAC control on and grant only to listed computers - the list doesn't accommodate enough MAC addresses, and the client has wireless and wired since it's a laptop. I also don't want to set static IPs on all of the devices since some cannot accommodate that feature.I'm thinking that reserving an IP address isn't ultimately the solution either, since assigning the IP isn't going to work if the MAC changes. how to use access control under these circumstances?
When attempting to configure access controls from the advanced menu I enable the access control checkbox. I then follow the configuration wizard completing each step as directed by the wizard. When I complete the wizard and try to save the rule I get the following error message regardless of how I complete the wizard. "Name can not be empty string". Yes, cannot is misspelled in the message. I have tried every combination of choices in the wizard and many combinations of naming the rule to no avail.
This did work properly on a previous firmware version, probably 1.04 or 1.05. I have not tried back loading to the previous versions to see where it did or did not work. I don't know how well the router goes back and don't really care to reload all the settings again by hand if the automatic recovery doesn't work.I want to use this feature to control what hours certain machines on the network have access to the internet.
I'm trying to block internet access to a range of IP addresses using the Access Control function of the DIR-655 router. Unfortunately, the router does not allow me to block a range of IPs. Instead, I can only create policies based upon individual IPs or MAC addresses. I have over 60 machines I want to block Internet access and I'd hate to have to type them in individually. How do I go about blocking all Internet access (HTTP/FTP/email/everything) for a range of IP addresses? They will have to be able to continue to use the internal LAN.
I would like to use the web access control that is on the DIR-615 along with my 2Wire modem/wireless router. Is this possible? If not is is possible to put the 2Wire modem into bridge mode and purchase a second wireless modem to run along side the DIR-615 that I have so that I can have two separate wireless networks that have two different web access controls in place?
I want to do what I thought would have been a simple enough task - block my kids phone/computer after certain hours. Instead of blocking the specified MAC address(es), all my computers does not have internet access. As soon as I disable the policy, internet access is on again. Here's what I did:
My firmware is 1.35NA and have a schedule established. When I try to add a policy for access control, I can select a policy name but when I hit "next", I get an error stating "Internet Explorer has stopped working" and wants to close. I was able to add policies previously but can not any more.
Trying to set up a simple schedule for keeping the kids from staying up all night. I'd had this working on a Linksys WRT54G till it bit the dust. I just want it to block internet after midnight. My problem is that the schedule is triggering the block unpredictably.?
I have a situation where I have tenants connecting to my wireless network and paying towards the internet bill. I am able to control this by using MAC filtering, but I have just realised that this only works for wireless clients.
Is there a way to replicate this for the router's Lan ports? Or possibly even just disable Lan access. The router model is a D-link DSL-2750U.
Region : Austria Model : TL-MR3420 Hardware Version : V2 Firmware Version : ISP :
I'd like to make exception keywords in the Access Control but I don't know how I could possibly do this. E.g. I have put in the keyword "apple" to be blocked, so if a domain has the keyword "apple" in it, it will be automatically blocked. What can I do, however, if I want to make an exception for the domain "appletree.com"? I haven't found any way to make an exception to specific domains or keywords.
I have several laptops at home that connect via wireless connection tot he DIR_655. Using the MAC address of those laptops, I want to prevent them from going to certain websites.Under 'Advanced" and "Website Filter", I addes several domain names (websudoku.com for example). I selected "DENY computersaccess to ONLY these sites". I then saved settings.I then went to "Access Control". I clicked on "Enable Access Control".I clicked on "Add Policy" to cdreate a new policy for one of the laptops.When I boot the laptop and go to one of the websites, it still allows me access. The URL/domain name is correct.
Region : UnitedStates Model : TL-WDR4300 Hardware Version : V1 Firmware Version : 3.13.23 Build 121225 Rel.37950n ISP :
Setting up access control for one PC. I just want to block all internet access to one PC during a certain time. It seems like my only options in the Access Control page in the GUI is to block websites or domains.
For some reason I can't get Access Control/Webaccess Filters working on my Dir-655 w/ 1.35NA. I've tried it with MAC and IP Address without any success. I've also enabled/disabled/enabled DNS Relay, recreated the rules, recreated the filters, etc. Nothing.
I'm trying to set up a website filter on my DIR-601. I created a policy for 2 MAC addresses, with a schedule from 10AM-6PM, selected "Block some websites", and disabled logging. Under website filter, I added some entries, and selected "DENY computers access to ONLY these sites". When the policy is enabled, and I try to access one of the blocked websites, it gets blocked correctly ("The URL access was denied by administrator.") However, for all other websites, I get "server unexpectedly dropped the connection" errors, eg "Safari can�t open the page [URL] because the server unexpectedly dropped the connection. This sometimes occurs when the server is busy. Wait for a few minutes, and then try again." or in Chrome "No data received. Unable to load the webpage because the server sent no data." This happens with ALL non-blocked websites. I'm using hardware version A1, firmware version 1.01NA.
I have a simple set-up: a DIR-655 with 2 devices plugged in to it. The Plex Media Server runs on Ubuntu Linux and acts as the DLNA server to a PS3 DLNA client. Both are hard-wired with ethernet cables to the DIR-655. In this set up the PS3 has trouble discovering the PLEX server via DLNA. A 'search for DLNA devices' on the PS3 fails to return the PLEX. Eventually, after some strange time interval ranging from 2-30 minutes, the PLEX server will show up on the PS3's list.
I attached a simple ethernet switch to the DIR-655 and then attached the PS3 and Plex/linux server to it. The PS3 now finds the Plex DLNA server INSTANTLY ... without even having to scan for servers.
It appears that the DIR-655 is trying to be 'useful' in some way by filtering some sort of traffic; multicast/igmp I assume. There don't appear to be any settings in the GUI to alter the Multicast/IGMP/DLNA/UPnP behavior in the LAN ... other then "turn UPnP on."
Note that this is hardware B1 and firmware 2.00NA.
I purchased a Epson Artisan 835, which I am runnung wireless. When I try to check the ink levels from my laptop they are all greyed out. Epson tech said the Dir-655 was the problem and that I needed to get the router to give permission for the ink levels to go through.
I have fiber optic net, going into a TP Link 1043 ND router out in my garage.All of the 4 lan ports go into one of the rooms in the house. I also have two more routers of the same kind, one downstairs and one upstairs.They are configured in a way, that DHCP server is only turned on, on the one in the garage, the other two act as switches.My problem is that 50 % of the time I can't acces facebook, and some other random sites.The interesting bit is that when I chat with someone on FB, I can see what they write, but my message doesn't go through.The way it goes, is that I can browse on facebook for like 5 minutes, after that its unavailable for another 5 minutes.I can still access the site from my smartphone, but only if its not connected to the wifi network, meaning the problem is somewhere within my setup.I've already tried turning the router firewall off, but that doesn't make any difference.
I have yet another problem now with the DIR-825. I have a DAP-1522 that I connect my multimedia devices to like my TV, BD player, etc.
For added security, I use MAC filtering to only allow access to my devices that connect to my router. However, after several hours, the devices connected to my DAP-1522 can no longer connect and neither can I connect to them. The odd thing is that I can connect just fine to the 1522 itself. I NEVER had this issue with the DIR-655 so I figured it had to be the 825. After trying several things, I essentially narrowed it down to the MAC filtering.
If I turn MAC filtering off everything works fine all the time. If I turn it on, everything works fine for several hours, even up to a whole day, but then eventually my devices can no longer see or be seen.
i have router lynksys WRT120N and the latest 18.104.22.168 firmware. And the problem occured frequently. At about 13.00 i went out, wifi was working okay. At around 18.00 i returned home and i was trying to connect to the wifi with my android phone, and suprisingly it did not work. I tried on my laptop and on a android tablet. It did not work. The only thing that i could figure it out is to reset the router. I checked the settings, and there was no access policy e.g. time based access blocking.
I recently bough for a home lab a sg300-10 switch. I have enabled layer 3 routing on it and have come across a puzzling issue. The switch is the default gw on this network, and in front of the switch there is a cable modem (ip route 0.0.0.0 0.0.0.0 192.168.0.7).
I have a newly aquired asa 5505 that I just set up to the bare minimum configurations. I followed a cisco paper on how to create a "remote access vpn" setup for ipsec. I can sucessfully connect and establish a VPN, but when I try to access an inside resource from the vpn address, the asa blocks it.
Specific error is:5 May 09 2012 15:17:48 305013 192.168.1.2 80 Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src outside:192.168.1.220/53101 dst inside:192.168.1.2/80 denied due to NAT reverse path failure
I have installed a new ASA5510 with CSC, and everything is working properly except the access to websites using https. All sites/access to them seem to be blocked by the ASA. I have read that this access is by default enabled and I have tried to add configuration to allow https access to the firewall but without success. [code]
I have a Cisco RV042 Wired Router. I've got a static IP and a MS Small Business Server in my Router Network. I have forwarded the essential ports to use the IIS and the Exchange Server of my SBS2011 (HTTPS, HTTP, smtp, rpc). I have also created some access rules for these ports, but I don't have any access on my server services, if the firewall is activated.
Here are my Firewall Access Rules from the RV042 Web Interface:
I have applied named access-list in output direction on 1GE interface on GSR12400 (IOS XR 3.4),but there is no matches. Counters doesn't increase although access-list blocks or permits certain packets (access-list works as it should).
We have a small office and already have a firewall in place that uses content filtering. I am looking for a low cost wireless access point that I can place behind my firewall that will allow me to control access by a username and password list, not just the passkey.
Does this exist without having to go to an Aruba or Ruckus type enterprise WIFI product?
I'm trying to set parental control for one of the kids in household, url...2gaming2Every Day 06:00 - 22:43 (meaning from 6am to 10:43pm he can acces ONLY those two sites, correct?)but, when I turn parental control on, all internet is off for him even allowed sites. Time right now is 21:44 gmt+2 and my router time is set right, so I don't know why it doest work?
For our children, we use the parental control feature of the DIR-615 (RevD, FW4.11b15), which works excellently. I use the whitelist feature, so only trusted web sites can be accessed. Unfortunately the DIR-615 only has 10 entries in that list and I will soon need more. So I wonder if there is another D-Link router that offers a bigger list with maybe 50 or even 100 entries?