TP-Link 3G/3.75G Router :: Exception Keywords / Domains For Access Control?
May 7, 2013
Region : Austria
Model : TL-MR3420
Hardware Version : V2
Firmware Version :
ISP :
I'd like to make exception keywords in the Access Control but I don't know how I could possibly do this. E.g. I have put in the keyword "apple" to be blocked, so if a domain has the keyword "apple" in it, it will be automatically blocked. What can I do, however, if I want to make an exception for the domain "appletree.com"? I haven't found any way to make an exception to specific domains or keywords.
View 2 Replies
ADVERTISEMENT
May 21, 2012
I would like to use the web access control that is on the DIR-615 along with my 2Wire modem/wireless router. Is this possible? If not is is possible to put the 2Wire modem into bridge mode and purchase a second wireless modem to run along side the DIR-615 that I have so that I can have two separate wireless networks that have two different web access controls in place?
View 1 Replies
View Related
Aug 5, 2012
Is there a way to block keywords and also customize the default page given when access is restricted?
View 1 Replies
View Related
Apr 23, 2012
I have a situation where I have tenants connecting to my wireless network and paying towards the internet bill. I am able to control this by using MAC filtering, but I have just realised that this only works for wireless clients.
Is there a way to replicate this for the router's Lan ports? Or possibly even just disable Lan access. The router model is a D-link DSL-2750U.
View 2 Replies
View Related
Apr 3, 2012
I'm configuring ASA 8.4 for SSLVPN allowing Web Portal access with group-url. I've noticed that if I put certain keywords after slash mark on group-url, client access would be denied by http 404 error.
Here's my configuration:
tunnel-group test type remote-access
tunnel-group test general-attributes
default-group-policy test
[Code].....
View 3 Replies
View Related
Oct 24, 2012
I have tried to setup access control by setting up a policy that restricts certain MAC addresses during a period during the day from certain websites. I set up the website filter and a schedule and selected them for the policy. Instead of blocking just the websites on the filter list during the time setup in the schedule, it blocks all websites all the time.I made sure that I setup the policy to 'block some access' NOT 'block all access'.The only thing that seems to work is that only the computers with the MAC address selected are effected.
View 3 Replies
View Related
Mar 2, 2010
I may be doing it incorrectly, but I'm trying to configure web access rules. I first set up access control and tell it to use the website filter. I've tried configuring it by both MAC address and IP address (separately, not simultaneously), but it still allows the listed sites in the web filter to get through. Is there something else I need to block or am I not doing something correctly? The network is on DHCP reservation, so IP addresses are always the same. MAC addresses, as I mentioned, don't work, either and they are fixed and logged in the router.
View 9 Replies
View Related
Dec 31, 2011
DIR655 with 1.33NA firmware. I'm trying to determine how to block access to the internet for a specific LAN computer when the user knows how to change a MAC address. I don't want to turn MAC control on and grant only to listed computers - the list doesn't accommodate enough MAC addresses, and the client has wireless and wired since it's a laptop. I also don't want to set static IPs on all of the devices since some cannot accommodate that feature.I'm thinking that reserving an IP address isn't ultimately the solution either, since assigning the IP isn't going to work if the MAC changes. how to use access control under these circumstances?
View 1 Replies
View Related
May 23, 2011
I have 60+ website domains to allow on my network using Website Fitering. Is it possible to expand it or is there another router out there that has a large amount of domain allowing or blocking?
View 1 Replies
View Related
Feb 26, 2008
When attempting to configure access controls from the advanced menu I enable the access control checkbox. I then follow the configuration wizard completing each step as directed by the wizard. When I complete the wizard and try to save the rule I get the following error message regardless of how I complete the wizard. "Name can not be empty string". Yes, cannot is misspelled in the message. I have tried every combination of choices in the wizard and many combinations of naming the rule to no avail.
This did work properly on a previous firmware version, probably 1.04 or 1.05. I have not tried back loading to the previous versions to see where it did or did not work. I don't know how well the router goes back and don't really care to reload all the settings again by hand if the automatic recovery doesn't work.I want to use this feature to control what hours certain machines on the network have access to the internet.
View 15 Replies
View Related
Jan 9, 2010
I'm trying to block internet access to a range of IP addresses using the Access Control function of the DIR-655 router. Unfortunately, the router does not allow me to block a range of IPs. Instead, I can only create policies based upon individual IPs or MAC addresses. I have over 60 machines I want to block Internet access and I'd hate to have to type them in individually. How do I go about blocking all Internet access (HTTP/FTP/email/everything) for a range of IP addresses? They will have to be able to continue to use the internal LAN.
View 3 Replies
View Related
Aug 8, 2012
I want to do what I thought would have been a simple enough task - block my kids phone/computer after certain hours. Instead of blocking the specified MAC address(es), all my computers does not have internet access. As soon as I disable the policy, internet access is on again. Here's what I did:
[code]...
View 4 Replies
View Related
Nov 3, 2011
My firmware is 1.35NA and have a schedule established. When I try to add a policy for access control, I can select a policy name but when I hit "next", I get an error stating "Internet Explorer has stopped working" and wants to close. I was able to add policies previously but can not any more.
View 3 Replies
View Related
Jan 25, 2012
Trying to set up a simple schedule for keeping the kids from staying up all night. I'd had this working on a Linksys WRT54G till it bit the dust. I just want it to block internet after midnight. My problem is that the schedule is triggering the block unpredictably.?
View 3 Replies
View Related
May 2, 2011
I have several laptops at home that connect via wireless connection tot he DIR_655. Using the MAC address of those laptops, I want to prevent them from going to certain websites.Under 'Advanced" and "Website Filter", I addes several domain names (websudoku.com for example). I selected "DENY computersaccess to ONLY these sites". I then saved settings.I then went to "Access Control". I clicked on "Enable Access Control".I clicked on "Add Policy" to cdreate a new policy for one of the laptops.When I boot the laptop and go to one of the websites, it still allows me access. The URL/domain name is correct.
View 5 Replies
View Related
Apr 10, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP :
Setting up access control for one PC. I just want to block all internet access to one PC during a certain time. It seems like my only options in the Access Control page in the GUI is to block websites or domains.
View 4 Replies
View Related
Jan 21, 2013
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : TL-WDR3600_V1_120820
ISP : Cox cable
It doesn't matter how I set it up, once the policy is enabled nothing can get through. This is the same for "deny" or "allow" as default. Is there bug with this new firmware TL-WDR3600_V1_120820??
View 2 Replies
View Related
Aug 28, 2011
For some reason I can't get Access Control/Webaccess Filters working on my Dir-655 w/ 1.35NA. I've tried it with MAC and IP Address without any success. I've also enabled/disabled/enabled DNS Relay, recreated the rules, recreated the filters, etc. Nothing.
View 14 Replies
View Related
May 4, 2011
I'm trying to set up a website filter on my DIR-601. I created a policy for 2 MAC addresses, with a schedule from 10AM-6PM, selected "Block some websites", and disabled logging. Under website filter, I added some entries, and selected "DENY computers access to ONLY these sites". When the policy is enabled, and I try to access one of the blocked websites, it gets blocked correctly ("The URL access was denied by administrator.") However, for all other websites, I get "server unexpectedly dropped the connection" errors, eg "Safari can�t open the page [URL] because the server unexpectedly dropped the connection. This sometimes occurs when the server is busy. Wait for a few minutes, and then try again." or in Chrome "No data received. Unable to load the webpage because the server sent no data." This happens with ALL non-blocked websites. I'm using hardware version A1, firmware version 1.01NA.
View 2 Replies
View Related
Apr 2, 2013
I have an EA4500. I am trying to block a specific site based on keywords in the webpage address. how to get the EA4500 to block sites with based on keywords.
View 1 Replies
View Related
Apr 24, 2012
I'm trying to set parental control for one of the kids in household, url...2gaming2Every Day 06:00 - 22:43 (meaning from 6am to 10:43pm he can acces ONLY those two sites, correct?)but, when I turn parental control on, all internet is off for him even allowed sites. Time right now is 21:44 gmt+2 and my router time is set right, so I don't know why it doest work?
View 14 Replies
View Related
Oct 3, 2011
We have an RVS-4000 router that we use as an Internet gateway on our school network. I am trying to set up an Internet Access Policy to block some specific websites by URL using a domain name. I set up the policy, and added a PC to the list using the mac address, and the blocking did not work. I went back to the list and added the IP address of the same PC, the policy still did not work to block the domain. I rebooted the router, cleared the Internet Temporary files and history on the PC, and the policy still does not work. It acts like it is going to block access to the website because it takes a long time, but it will eventually connect.
View 7 Replies
View Related
Mar 2, 2012
in office we have a broadband internet to 6 systems one router .I want to control the partcular system internet
View 1 Replies
View Related
Dec 12, 2012
I am having some issues with creating an ACL for my gateway router.I want to block external access to my network 192.168.1.0/24 from internet so i set up the ACL on the WAN port of my 7200 router asI am using named extened access list -
{
deny ip any 192.168.1.0 0.0.0.255 log
permit ip any any
}
and i applied this inbound accesslist on the WAN port of router as
"ip access-group acl-in in"
Now i have blocked the external traffic to my network 192.168.1.0/24 but the issue i am having is i am also unable to reach outside now. All i want is to block external traffic on the router WAN port but allow internal traffic to outside. Did i miss anything in the access list?
View 5 Replies
View Related
Apr 2, 2013
Region : UnitedKingdom
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :
Looking at the manual for this router in regards to bandwidth restrictions.When you set up the Rules under Bandwidth Control does this setting shared by the IP range or does each IP in the range get that amount of bandwidth?
View 1 Replies
View Related
Oct 2, 2011
Why does my E1200 forget my Parental Control Password? This happens almost weekly and I have to use the "forgot password" option. It asks my security question, I answer it and set the new password to the same password it keeps forgetting. Why does this happen? Also, is there anyway to have total 24hr control on the Block Internet Access?
View 4 Replies
View Related
Jan 20, 2011
What is the maximum number of websites or keywords Linksys WAG160N can block?
View 1 Replies
View Related
Jul 24, 2012
I've set up my E3000 (and the WRT54g it replaced) to use dynamic DNS (using dyndns.org) to forward a domain to a particular IP address on the network. Works awesomely.
I now have a situation where I am setting up a local network (no internet access) where I want a few other local users (an iPad and a laptop) to be able to access a couple websites (let's say x.me and y.me) on a machine also connected to the router.
As an aside, It seems (just from casual testing) that if I am on a machine on my local network and I try to access my dynamic domain (that I route through dyndns.org) and it seems to resolve right away without going out to the internet. Is this correct? Does it automatically route anything on lan directly?
View 4 Replies
View Related
Sep 28, 2009
I've been having a weird issue lately with my WRT310Nv2. Sometimes when we, and by we, I mean two different computers (one Mac, one XP PC), try to go to a website, it will point us to an entire diffrently website. For example, earlier today I attempted to go to Twitter and twitter.com appeared as some random Blogger website. I've had issues where Amazon.com kepting point to UPS.com, or Facebook.com pointing to MySpace.com, etc.
I haven't been able to pinpoint a regular pattern, except the fact that it is most likely the wireless network, since the Windows PC (Server 2003) plugged directly into the router has never had this issue.
View 9 Replies
View Related
Dec 14, 2011
When I try to print over the network I'm getting a dicom toolkit exception error. Any idea what this means and how to correct.
View 1 Replies
View Related
Oct 29, 2012
So i see tons of threads here and on google talking about dns issues with their linksys router but I never see a solution other than to locally change the dns servers on the client machine to prevent it from using the linksys router dns. My router is the WRT310Nv2 running the latest firmware but I see others are affected as well. url...My issue is this router continues to fail dns resolutions and I have to either reset it or tell my client machine not to use my router as a point of dns resolution.
1. Why is my router failing to resolve domains correctly?
2. Is there anyway to fix this from the router?
View 7 Replies
View Related
Nov 27, 2012
We have a small office and already have a firewall in place that uses content filtering. I am looking for a low cost wireless access point that I can place behind my firewall that will allow me to control access by a username and password list, not just the passkey.
Does this exist without having to go to an Aruba or Ruckus type enterprise WIFI product?
View 1 Replies
View Related
May 7, 2013
On our public wi-fi network we have an acceptable use policy page that users must accept in order to access the internet. However I would like to exclude a few devices from having to do this. We have a couple of Kindle devices from a vendor that they configured to automatically connect to the internet for updates twice a day. But they cannot accept the policy so they are blocked.
View 3 Replies
View Related
