Trying to set up a simple schedule for keeping the kids from staying up all night. I'd had this working on a Linksys WRT54G till it bit the dust. I just want it to block internet after midnight. My problem is that the schedule is triggering the block unpredictably.?
View 3 Replies
I may be doing it incorrectly, but I'm trying to configure web access rules. I first set up access control and tell it to use the website filter. I've tried configuring it by both MAC address and IP address (separately, not simultaneously), but it still allows the listed sites in the web filter to get through. Is there something else I need to block or am I not doing something correctly? The network is on DHCP reservation, so IP addresses are always the same. MAC addresses, as I mentioned, don't work, either and they are fixed and logged in the router.
View 9 Replies View RelatedI bought a TP-Link TL-WR841N which i have managed to setup up properly, i am able to connect to the wireless and get internet access. However the minute i walk out of the room or a few meters away i am disconnected and i can't re-connect, i get the "windows cannot connect to TP-LINK" message. The signal strength in on excellent and i know it works because when i stand near it, it works perfect.I phoned TP-LINK technical support who were pretty useless and couldn't fix the problem.
View 3 Replies View RelatedI've been able to copy files to the WD drive attached to my DIR-655 router but Ghost gets an error even though is recognizes the drive is connected.
View 4 Replies View RelatedI have configured my CIsco 2911 router and there seems to be something wrong with my configuration regarding subinterface 0/0.102 The hosts on this subnetwork cant access the Internet and i cant spot the error.
Here is my running config on this matter.
class-map type inspect match-any LAN_TO_WAN
match access-group name LAN_TO_WAN
class-map type inspect match-any WAN_TO_LAN
match access-group name WAN_TO_LAN
class-map type inspect match-any GRE_TO_WAN
match access-group name GRE_TO_WAN
class-map type inspect match-any WAN_TO_GRE
[code]....
I am purchasing a new DIR 600. It pings properly, but didn't access internet. I am using HP Desktop and ORTEL broadband connection.
View 1 Replies View RelatedI have tried to setup access control by setting up a policy that restricts certain MAC addresses during a period during the day from certain websites. I set up the website filter and a schedule and selected them for the policy. Instead of blocking just the websites on the filter list during the time setup in the schedule, it blocks all websites all the time.I made sure that I setup the policy to 'block some access' NOT 'block all access'.The only thing that seems to work is that only the computers with the MAC address selected are effected.
View 3 Replies View RelatedDIR655 with 1.33NA firmware. I'm trying to determine how to block access to the internet for a specific LAN computer when the user knows how to change a MAC address. I don't want to turn MAC control on and grant only to listed computers - the list doesn't accommodate enough MAC addresses, and the client has wireless and wired since it's a laptop. I also don't want to set static IPs on all of the devices since some cannot accommodate that feature.I'm thinking that reserving an IP address isn't ultimately the solution either, since assigning the IP isn't going to work if the MAC changes. how to use access control under these circumstances?
View 1 Replies View RelatedI have 60+ website domains to allow on my network using Website Fitering. Is it possible to expand it or is there another router out there that has a large amount of domain allowing or blocking?
View 1 Replies View RelatedWhen attempting to configure access controls from the advanced menu I enable the access control checkbox. I then follow the configuration wizard completing each step as directed by the wizard. When I complete the wizard and try to save the rule I get the following error message regardless of how I complete the wizard. "Name can not be empty string". Yes, cannot is misspelled in the message. I have tried every combination of choices in the wizard and many combinations of naming the rule to no avail.
This did work properly on a previous firmware version, probably 1.04 or 1.05. I have not tried back loading to the previous versions to see where it did or did not work. I don't know how well the router goes back and don't really care to reload all the settings again by hand if the automatic recovery doesn't work.I want to use this feature to control what hours certain machines on the network have access to the internet.
I'm trying to block internet access to a range of IP addresses using the Access Control function of the DIR-655 router. Unfortunately, the router does not allow me to block a range of IPs. Instead, I can only create policies based upon individual IPs or MAC addresses. I have over 60 machines I want to block Internet access and I'd hate to have to type them in individually. How do I go about blocking all Internet access (HTTP/FTP/email/everything) for a range of IP addresses? They will have to be able to continue to use the internal LAN.
View 3 Replies View RelatedI would like to use the web access control that is on the DIR-615 along with my 2Wire modem/wireless router. Is this possible? If not is is possible to put the 2Wire modem into bridge mode and purchase a second wireless modem to run along side the DIR-615 that I have so that I can have two separate wireless networks that have two different web access controls in place?
View 1 Replies View RelatedI want to do what I thought would have been a simple enough task - block my kids phone/computer after certain hours. Instead of blocking the specified MAC address(es), all my computers does not have internet access. As soon as I disable the policy, internet access is on again. Here's what I did:
[code]...
My firmware is 1.35NA and have a schedule established. When I try to add a policy for access control, I can select a policy name but when I hit "next", I get an error stating "Internet Explorer has stopped working" and wants to close. I was able to add policies previously but can not any more.
View 3 Replies View RelatedI have a situation where I have tenants connecting to my wireless network and paying towards the internet bill. I am able to control this by using MAC filtering, but I have just realised that this only works for wireless clients.
Is there a way to replicate this for the router's Lan ports? Or possibly even just disable Lan access. The router model is a D-link DSL-2750U.
Region : Austria
Model : TL-MR3420
Hardware Version : V2
Firmware Version :
ISP :
I'd like to make exception keywords in the Access Control but I don't know how I could possibly do this. E.g. I have put in the keyword "apple" to be blocked, so if a domain has the keyword "apple" in it, it will be automatically blocked. What can I do, however, if I want to make an exception for the domain "appletree.com"? I haven't found any way to make an exception to specific domains or keywords.
I have several laptops at home that connect via wireless connection tot he DIR_655. Using the MAC address of those laptops, I want to prevent them from going to certain websites.Under 'Advanced" and "Website Filter", I addes several domain names (websudoku.com for example). I selected "DENY computersaccess to ONLY these sites". I then saved settings.I then went to "Access Control". I clicked on "Enable Access Control".I clicked on "Add Policy" to cdreate a new policy for one of the laptops.When I boot the laptop and go to one of the websites, it still allows me access. The URL/domain name is correct.
View 5 Replies View RelatedRegion : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP :
Setting up access control for one PC. I just want to block all internet access to one PC during a certain time. It seems like my only options in the Access Control page in the GUI is to block websites or domains.
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : TL-WDR3600_V1_120820
ISP : Cox cable
It doesn't matter how I set it up, once the policy is enabled nothing can get through. This is the same for "deny" or "allow" as default. Is there bug with this new firmware TL-WDR3600_V1_120820??
For some reason I can't get Access Control/Webaccess Filters working on my Dir-655 w/ 1.35NA. I've tried it with MAC and IP Address without any success. I've also enabled/disabled/enabled DNS Relay, recreated the rules, recreated the filters, etc. Nothing.
View 14 Replies View RelatedI'm trying to set up a website filter on my DIR-601. I created a policy for 2 MAC addresses, with a schedule from 10AM-6PM, selected "Block some websites", and disabled logging. Under website filter, I added some entries, and selected "DENY computers access to ONLY these sites". When the policy is enabled, and I try to access one of the blocked websites, it gets blocked correctly ("The URL access was denied by administrator.") However, for all other websites, I get "server unexpectedly dropped the connection" errors, eg "Safari can�t open the page [URL] because the server unexpectedly dropped the connection. This sometimes occurs when the server is busy. Wait for a few minutes, and then try again." or in Chrome "No data received. Unable to load the webpage because the server sent no data." This happens with ALL non-blocked websites. I'm using hardware version A1, firmware version 1.01NA.
View 2 Replies View RelatedIm having a problem with my wireless. My whole family is connented. to wireless. But when we all use it together it goes so slow. Like 4 some times only 2 people using it at the same time.
View 9 Replies View Relatedi had an extra network under my wireless networks that was just called "network" which was not connected to anything, but since i had this, on the bottom right of my screen where it normally showed the bars for the wireless connection, it had the bars grey with a red X on them, but my connection worked fine still.I am using windows 7 64x bit. I always use a wireless connection on my laptop.
View 6 Replies View RelatedI have 2 computers, One running Vista 32, Desktop.Another, Laptop, Win 7 64bit.Both computers have given Error 651 when using PPPoE wired connections, usually at the peak of the day.My ISP says that Error 651 is the problem, while I am starting to think its the amount of bandwidth their giving my neighborhood/home.Also, can that dosen't work,how to fix the overall problem of my Internet shutting off at peak hours?
View 2 Replies View Relatedwhen I couldnt turn on the wifi from the switch. It remained orange(which is its off state) and so I went to the device manager and the wifi adapter was shown there but with an exclamation mark. Showing the error "the device cannot be started(code 10)". So I uninstalled and rebooted, only to get the same error when it got reinstalled.
View 19 Replies View RelatedI have a Netgear CVD31T modem delivered by my internet provider. I can't change any settings on the modem. My connection speed is 30 gb up and 5 GB down.Until now I used a Linksys WRT54GV ver. 2 router to share my connection between my computers and NAS server and it worked ok. In speed tests I normally get approx 25 - 28 GB speed. To optain more speed on my LAN I want to buy a GB router. And here started my problems. First I tried a D-link DIR655, then a Netgear WNDR3700 and latest a Linksys E3000. I all 3 occations my WAN speed droped drasticaly down to between 3 - 5 GB speed, at under a ping test I have a loss of between 10 - 30 % and time on approx 50 ms.If I connect my PC directly to the modem or re-connect my old router it works perfect. I have tried to replace cables etc. etc.
View 5 Replies View RelatedLast night on the xbox 360 i was suddenly experiencing alot of lag on other peoples voices. i took no notice of it and the next day i went on my laptop and alot of websites wouldn't load properly.i can go on google,obviously this and my hotmail(after having to wait a long time for the hotmail to load), but others such as ebay will not load. I cannot even access my router settings by typing in my ip address, instead i get a message saying the page cannot be found. also i was disconnected from xbox live with the internet to xbox live part not working. Obviously the first thing i done was turn the router off and back on but it hasn't made any difference.
OS Version: Microsoft Windows Vista Home Premium , Service Pack 2, 64 bit
Processor: Pentium(R) Dual-Core CPU T4200 @ 2.00GHz, Intel64 Family 6 Model 23 Stepping 10
Processor Count: 2
RAM: 4055 Mb
Graphics Card: Mobile Intel(R) 4 Series Express Chipset Family, 1804 Mb
Hard Drives: C: Total - 290204 MB, Free - 141170 MB; E: Total - 14999 MB, Free - 5644 MB;
Motherboard: Dell Inc., 0G848F, , .5MDJWJ1.CN7016697U05OT.
Antivirus: AVG Anti-Virus Free Edition 2011, Updated and Enabled
how u would evaluate the effectiveness of the home entertainment (PC,console, Windo media centre
View 1 Replies View Relatedive been having some issues with my internet, i had an attack on my pc recently by some american orginization, ive reinstalled new windows on my pc, reset my modem, and nothign seems to work, i have too many tunnel adapters in cmd ip config i think, bell canada hooked up my internet lines and they actually joined two or more wires together and strung them up on the neighbours fence and mine and even wrapped it around a tree branch, god knows why they would even do that, maybe they think when the tree grows it will cost me money to fix it and theyll earn from thier mistakes instead of learn from them... anyway this is my ipconfig test results as explained in previous post from someone.Windows IP Configuration[CODE]
View 1 Replies View RelatedSome Trouble With My Wired Internet Connection,basically it worked somedays other days it cut off and didnt work for a few days,i phoned virgin media who sent me a new modem.Everything is set up and activated and it worked for about a day,now it has stopped working even though the computer says im connected,everytime i try internet explorer or firefox i get a white screen and every webpage i try fails,but if i bring up utorrent i can see that my internet is connected because it begins to download the ebooks
View 17 Replies View RelatedSo I have an HP Pavilion dv9000 laptop with window 8 installed and when I try to connect to the internet I keep getting an error that says the "Ethernet" Adapter is not working properly. I used to be able to go on the internet and then my dad had my computer for a while and now it's not working.
View 7 Replies View RelatedI recently replaced a Linksys wireless router with a Netgear wireless router(provided by Comcast) to the modem in my house. I used my HP Pavilion as the computer to run the setup disk and the wireless wizard to link the new router to the modem. I unplugged my HP from the router and proceeded to setup my computer on the wireless network.
View 14 Replies View RelatedWhen I check the strength sometimes it indicates it's good if I'm practically sitting on top of the router, this seems to eventually degrade to low until finally the connection drops.Repairing' with XP repair facility doesn't work. I can forget about getting a connection if I move further away from the router. At the moment I'm relying on using an ethernet cable snaking across the dining room, which isn't really practical with a toddler and a dog racing around. Recently a friend put a bigger HD in and before this it was working fine, so I suspect that it may be due to this. I think it's due to the wirless card in the laptop, as I have a number of other devices in the house which all work fine.
View 4 Replies View Related
