I am building a new computer to replace my existing one. is there a way to transfer my existing network to the new computer when I install the routers software? I don't want to redo all the devices that are connect wirelessly that are using it for internet connection.
View 1 Repliesit's across 3 floors and the current setup is a single wireless router DIR655 (1st floor), but the WiFi suffers greatly on the floor below/above.
I have sourced 3x D link switches and 2x more DIR655's and would like to have all machines/consoles/phones etc in the household on the same network. Is it possible to keep one DIR655 as the main wireless connection and have the other as pure AP's as well as keeping the same SSID?
As part of my course, I have to install a brand new network, including cabling, setting up equipment etc in a room whilst ensuring that the current network system for that room is still running without any issue. How to do this as it includes taking out/changing the infrastructure in relation to cabling?
View 5 Replies View Relatedearlier today my modem died so I looked around and found an old modem (D-Link DSL-300T) lying around so I decided to use that one instead of purchasing a new one. It always worked great in the past, but when I tried it today I can only find a connection on this computer (garbage computer), the other 2 computers in my network can't connect to the internet, they can't even connect to the network at all. Oh and the router I'm using is a D-Link DIR-100. This computer is running windows XP, so is another one in the network and the one I want the connection to work on is running windows 7.
View 1 Replies View RelatedEarlier today my modem died so I looked around and found an old modem (D-Link DSL-300T) lying around so I decided to use that one instead of purchasing a new one.It always worked great in the past, but when I tried it today I can only find a connection on this computer (garbage computer), the other 2 computers in my network can't connect to the internet, they can't even connect to the network at all.Oh and the router I'm using is a D-Link DIR-100. This computer is running windows XP, so is another one in the network and the one I want the connection to work on is running windows 7.
View 11 Replies View RelatedI am about to buy a Netbook from HP with windows 7 Starter.But a few days back when I tried to connect my friend's laptop to my network using WiFi ,it accessed the Internet but did not detect any other XP computers on the Network neither could I ping them nor could I access their shared folders.
2)And What is N Draft?? and how is it different from WiFi-N?
3)And can I set up Guest Network so that I can give the connected computers Internet access but no Shared Folder access..
The modem connects to a D-Link DIR-655 which connects to a computer (Vista) and a switch, the switch then connects to another computer (Win7) and an xbox. the problem is that the vista computer will randomly connect and disconnect from the internet/ network. The vista computer also generally runs very slow on the internet. The Win7 computer runs perfectly and there is never an issue, so I'm wondering if the problem has to do with the vista computer not being connected to the switch? It is not an issue with the router, I have tried two already and the same issue occurs.the vista computer is running with a Gigabyte GA-EP45-UD3R which has a Realtek 8111C LAN chipset.
View 5 Replies View RelatedLooking at getting an older second computer onto the internet. We have a wireless connection on the primary computer so I was looking at the TP-Link TL-WN321G USB network adapter, or the TP-LINK WN350GD PCI network adapter.The end goal of course is to get the old computer onto wireless, but not sure what the best way to do it is. I'd think the motherboard would accept the PCI card though we do somewhat lack USB facilities. The computer uses a USB hub which I'm not sure if it would impact on internet speeds at all.
View 3 Replies View RelatedI'm desperately trying to set up my old D-Link DI-524 on my parent's Toshiba laptop...I'm visiting and going thru withdrawals! I've installed it, run the wizard etc but it doesn't work...not even wired. I've tried various cable configurations and I get nothing. Both cables are good and work just fine connected to the modem. I've reset it a few times, upgraded the firmware and still nothing...I'd think I'd at least get it to work hard wired. My laptop can see the network I set up even...but no data transmission. I'm not a wireless expert, but I need to become one fast!
View 3 Replies View RelatedMy home desk top is set up with D-Link Xtreme N Dual Band Router. I have no problems accessing the internet on my desk top computer. I am trying to access my home wireless network through my HP laptop computer. The wireless network status is Limited or no Connectivity. I've tried the "repair" button with no resolution. The wireless connection is set to automatic.
View 1 Replies View RelatedI run a minecraft server over an ad hoc network, but every time we start the server up again, we have to find the new IP address, edit the server files, and re-enter the new IP address onto all the computers.Is there a way to make it so an Ad Hoc always boots with the same Ip Address?
View 2 Replies View RelatedI have multiple devices running on my home network. Every once in a while my wireless router starts playing up and I have to reset it.Whenever this happens, it changes the internal IP addresses of the devices. Is there a way to make the router keep the same internal ip address for each device? ie Laptop stays at 192.168.1.8I have a few forwarded ports for remote access to certain pieces of software, so each time the address changes, I have to go in and change these details, which is quite frustrating.
View 7 Replies View RelatedI have a wireless repeater (NETGEAR Universal Wifi Range Extender WN2000RPT) thats been giving me issues lately when attempting to use it to connect an xbox 360 I have to xbox live. The Xbox and the repeater are connected by an ethernet cable so there is no wireless connection going on between them. My router (Cisco WRVS4400N Wireless-N Gigabit Security Router with VPN) located in the basement of my house, and the extender is on the second floor of my house. The xbox that I want to connect to the internet is located on this second floor and because of the distance between it and my router a normal xbox wireless networking adapter doesn't seem to be working.Anyway, if I plug in the extender and let it get a connection, and use it right away to connect, i have no issues. The connection will also usually remain working for a while after I first get it working. The problem comes after I'm done using the xbox and i shut off the console and the tv. When I come back to the xbox later and turn it on, the networking extender still shows it has a full connection and is working properly on the outside with the green lights, but the xbox will not connect and it will tell me the extender is not assigning an IP automatically (DHCP turned off), when I know for a fact it is turned on. It is almost like the extender freezes after I leave it alone and on for a while. When this happens I usually unplug it and let it connect, and everything works as it should again. After a while its gotten a little annoying having to do this every time I need connection.
View 5 Replies View RelatedKeep a log of my own (Wan) IP-adress. It should look up my own IP-address and write it away to a log, so that I can look up a few weeks or months later what my IP-adress was on a certain day. I am using a router at home.
View 6 Replies View RelatedI would like to know if it is possible to add a second router to my home network.
My son wants to use his Nintendo DS online but the device does not have WEP capability, it can only deal with the less secure WPA option.
I am not willing to drop my preferred WEP just to facilitate one device, but I do have a spare router and I am wondering if it were possible to hook the second router up and allow him to connect using WPA?
I have two dir655 routers that are connected. The second router is not setup as a wireless access point, but I am open to that if it will work. The second one is going to serve as a public wifi in a business, with a separate SSID. The first one is going to handle the local business network, with its NAS and printers. How would I prevent the public wifi from accessing the first router?
I have tried the guest wifi partition setting, however it still allows access to the lan devices on the first router. It does partition with the second router properly though, but thats not worth anything to me cause there are no lan devices on the 2nd router.
Would it work right if I turn the 2nd router into a access point, disable the dhcp server, and set it up with the guest wifi partition?
ASR performs the function of ISG. The number of subscribers until 10000. This number is constantly growing.Because of the economic address space subscribers surf the Internet through NAT.Now the task to keep logs of all translations or binds. Need to store the information about what time, certain internal IP address using the external IP.
View 19 Replies View RelatedI am installing a network that has two SG500X-24 switches as core and several SG300-52 switches as access switches. I've seen in the SG500X-24 datasheet that there is a True Stacking feature. But in the data sheet there are not a lot of details about it. My doubt is the following. If I configure the two SG500X-24 switches as a single switch through stacking them, can I connect one SG300-52 switch to these two SG500X-24 switches through two cables (both configured as a LAG in the SG300-52 and in the SG500X-24 stack, one cable per SG500X-24), the the first cable connected to the first SG500X-24 switch and the second cable connected to the second SG500X-24 switch and keep both connections active?
View 3 Replies View RelatedI have been testing WiFi devices such as the iPhones and iPads connectivity with the following setup:
1. 3502i AP
2. WLC 5508 SW 7.0.98
3. NGS
The i-devices have iOS v4.2
My goal is to have the guest user i-devices maintain the credentials (username and password) when they login again to the wireless network. Like if the device sleep, I think definitely they would loose those IP address issued by the DHCP. Once the guest user uses them again and connect them to the wireless network the user would not need to type-in those credentials on the Web Authentication page directed by the WLC.
The credentials are issued by the sponsor who created them on the NGS. It seems that there are WiFi problems with these i-devices. But somehow, I'm looking for a solution that would automated the logins like a checkbox if you want to be kept signed in, on Yahoo or Stay signed in for GMail.
Have a WLC 5508 running 6.x code with LAP's providing wireless for our internal laptops (WPA2 and EAP-TLS). I want to provide guest wireless which goes out a different port on the WLC to a guest firewall/cable modem. However, we want to prevent our internal laptops from being able to use the guest wireless. I have RADIUS (IAS) and LDAP for my AD available. We would prefer not to have use Lobby Ambassador and just have the guests use a simple password or web passthru. Guests may be laptops or smartphones. What options are available? I have tried a test setup using dynamic vlan assignments from RADIUS using the IETF flags, but can't seem to get it to work. Is there a way to identify the SSID is being used at the RADIUS server?
View 13 Replies View RelatedHaving problems with my wireless router, dropping and keeping connection active. For some odd reason I keep dropping connection either wireless or wired. I have a total of 5 items going through this router. 2 of them are wireless and the other 3 are wired. The wireless items are a desktop computer that is using the Wireless USB adapter to get online. Sometimes it drops and most of the time it doesn’t have any problems. I have a laptop that sometimes the connection goes from strong all the way down to no connection at ALL. It starts at 54MBPS to down to the RED X over the wireless manager. Forgot to mention both of these machines are Windows XP. If I reboot the laptop, it comes up without any problems.
Sometimes I tell Windows XP to manage the Wireless connection and tell it to disconnect and re-connect again, it goes. Now for the wired items, I have 2 gaming systems and another computer plugged directly up to the router. For some odd reason when I double click on the internet, on the computer that is hooked directly to the router, it says page couldn’t be found. I know that there is connection and there is nothing running in the task tray except for the Anti-Virus and Firewall. The browsers that I am using are Internet Explorer 8 and Mozilla Firefox 3.0.10. Also checked on the back of the machine to see if I have link lights and everything is flashing. Finally, when I click the homepage or refresh button about 2 or 3 times, it goes through.
think that I am overloading this Router and it can’t handle it. I might have to look into sending "Keep Alive" packet setting on the router.
We have a Linksys E1200 modem and I have been having problems with keeping my son from using the wireless interenet. I did change the password and that worked for about 24 hours and then he was able to get onto it again. He has a nintendo dsi and he is smart enough to figure out how to dismantle any parental controls on his gaming device. I think that he resets the modem in order to get back onto the internet in order to use his gaming device. Someone told me that you can register each item individually in order to keep kids from using it but I have no idea as to how this works. We have two iphones, a lap top, and two tablets.
View 7 Replies View RelatedI have a Cisco 877W-K9 router, and I for the life of me can not work out how to enable multiple SSIDs on the AP whilst keeping them all to the same VLAN?
I know this may seem silly but basically for our clients we setup WPA-Enterprise for one SSID and WPA-PSK for the other to help ease migration between the two etc, however all I can seem to do at the moment is create multiple VLANs and use ip unnumbered vlan1 to sync them all into one, but this seems really silly.
how to sending out the wireless network from computer A to computer B if we used a lan network to computer A
View 12 Replies View RelatedI have a home network running all Mac computers (though can run Windows VM if necessary) and a pair of USB printers. The wireless router and cable modem are in one room, but the printers are in another. I'd like to find the most practical way to add the printers to the local wireless network without sharing them from a computer. I've tried that for a while, but don't want to leave a laptop connected 24/7 just to enable wireless printing (rather defeats the purpose of a portable computer). I don't have any wired network lines in the home, and am not excited by the idea of running any cables.
View 5 Replies View RelatedThere is already a laptop running wirelessly through the D Link DIR 615. I want to add another to the network and cannot. What do I need to do to pick up the wireless network already running?
View 5 Replies View RelatedI have a question about my windows systems(XP and Vista) re-connecting to my network folders when my computers restart. I have some shared network folders on my Synology DS410. And then i mapped a network drive to use those folders.But every time i restart my computer i get the message "cannot reconncet all network drives"I have to put in my username and password everytime. I choose Remember login and password.How can i fix this so it automatically connects to these on restart?
FYI...
1 computer - Windows Vista Home Premium
1 computer - Windows XP Home
Both connected via wired LAN
My iSCSI drives connect just fine on restart. Just not my mapped network folders.
My computer is a 32 bit, Win7 SP1 with Pentium Dual Core 2.6 Ghz and 2Gb of Ram on a wired network. My wife has a similar system using a wireless network. She can ping my IP Address, but I cannot ping hers. We both have full access to the Internet. We are using the same workgroup, and both computers have file and printer sharing enabled and IPv6 addresses and DNS server addresses selected automatically.The problem appears to be with my computer?
Here are my system stats:
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 32 bit
Processor: Pentium(R) Dual-Core CPU E5300 @ 2.60GHz, x64 Family 6 Model 23 Stepping 10
Processor Count: 2
RAM: 2013 Mb
Graphics Card: Intel(R) G41 Express Chipset, 782 Mb
Hard Drives: C: Total - 76308 MB, Free - 49226 MB; D: Total - 286167 MB, Free - 52893 MB; M: Total - 38154 MB, Free - 7 MB;
Motherboard: ASUSTeK Computer INC., P5G41-M LE
Antivirus: Microsoft Security Essentials, Updated and Enabled
I am sure this has been asked before, but how do you put in your own computer name into the MAC filtering?
View 2 Replies View Relatedmy D-Link DIR-600 router cannot connect to my computer and it cannot access internet connection
View 11 Replies View RelatedPlug in D-link download drivers but computer can't find D-link reboot plug in after downloading drivers wont see it.
View 1 Replies View RelatedI recently bought the D-link DWA 556 wireless adapter. I tried installing it but the computer couldn't find it in the device manager. I tried 3 different slots and I had the same problem each time.
I called tech support and he said that my motherboard must not be compatible with the card. I don't think this is the case but it was the only advice he could give me. I have an MSI P67A-G45 board. I removed all drivers from my previous card before installing the DWA 556 because I heard they can clash with each other.
I have a DIR-615 router that I can not see the characters that you have to type just a read X on login screen on any computer running IE9 even the emulator on the dlink site shows this problem.
View 7 Replies View Related