I run a minecraft server over an ad hoc network, but every time we start the server up again, we have to find the new IP address, edit the server files, and re-enter the new IP address onto all the computers.Is there a way to make it so an Ad Hoc always boots with the same Ip Address?
View 2 RepliesKeep a log of my own (Wan) IP-adress. It should look up my own IP-address and write it away to a log, so that I can look up a few weeks or months later what my IP-adress was on a certain day. I am using a router at home.
View 6 Replies View RelatedI have multiple devices running on my home network. Every once in a while my wireless router starts playing up and I have to reset it.Whenever this happens, it changes the internal IP addresses of the devices. Is there a way to make the router keep the same internal ip address for each device? ie Laptop stays at 192.168.1.8I have a few forwarded ports for remote access to certain pieces of software, so each time the address changes, I have to go in and change these details, which is quite frustrating.
View 7 Replies View RelatedI have a wireless repeater (NETGEAR Universal Wifi Range Extender WN2000RPT) thats been giving me issues lately when attempting to use it to connect an xbox 360 I have to xbox live. The Xbox and the repeater are connected by an ethernet cable so there is no wireless connection going on between them. My router (Cisco WRVS4400N Wireless-N Gigabit Security Router with VPN) located in the basement of my house, and the extender is on the second floor of my house. The xbox that I want to connect to the internet is located on this second floor and because of the distance between it and my router a normal xbox wireless networking adapter doesn't seem to be working.Anyway, if I plug in the extender and let it get a connection, and use it right away to connect, i have no issues. The connection will also usually remain working for a while after I first get it working. The problem comes after I'm done using the xbox and i shut off the console and the tv. When I come back to the xbox later and turn it on, the networking extender still shows it has a full connection and is working properly on the outside with the green lights, but the xbox will not connect and it will tell me the extender is not assigning an IP automatically (DHCP turned off), when I know for a fact it is turned on. It is almost like the extender freezes after I leave it alone and on for a while. When this happens I usually unplug it and let it connect, and everything works as it should again. After a while its gotten a little annoying having to do this every time I need connection.
View 5 Replies View RelatedI am building a new computer to replace my existing one. is there a way to transfer my existing network to the new computer when I install the routers software? I don't want to redo all the devices that are connect wirelessly that are using it for internet connection.
View 1 Replies View RelatedI would like to know if it is possible to add a second router to my home network.
My son wants to use his Nintendo DS online but the device does not have WEP capability, it can only deal with the less secure WPA option.
I am not willing to drop my preferred WEP just to facilitate one device, but I do have a spare router and I am wondering if it were possible to hook the second router up and allow him to connect using WPA?
I have two dir655 routers that are connected. The second router is not setup as a wireless access point, but I am open to that if it will work. The second one is going to serve as a public wifi in a business, with a separate SSID. The first one is going to handle the local business network, with its NAS and printers. How would I prevent the public wifi from accessing the first router?
I have tried the guest wifi partition setting, however it still allows access to the lan devices on the first router. It does partition with the second router properly though, but thats not worth anything to me cause there are no lan devices on the 2nd router.
Would it work right if I turn the 2nd router into a access point, disable the dhcp server, and set it up with the guest wifi partition?
As part of my course, I have to install a brand new network, including cabling, setting up equipment etc in a room whilst ensuring that the current network system for that room is still running without any issue. How to do this as it includes taking out/changing the infrastructure in relation to cabling?
View 5 Replies View RelatedASR performs the function of ISG. The number of subscribers until 10000. This number is constantly growing.Because of the economic address space subscribers surf the Internet through NAT.Now the task to keep logs of all translations or binds. Need to store the information about what time, certain internal IP address using the external IP.
View 19 Replies View RelatedI am installing a network that has two SG500X-24 switches as core and several SG300-52 switches as access switches. I've seen in the SG500X-24 datasheet that there is a True Stacking feature. But in the data sheet there are not a lot of details about it. My doubt is the following. If I configure the two SG500X-24 switches as a single switch through stacking them, can I connect one SG300-52 switch to these two SG500X-24 switches through two cables (both configured as a LAG in the SG300-52 and in the SG500X-24 stack, one cable per SG500X-24), the the first cable connected to the first SG500X-24 switch and the second cable connected to the second SG500X-24 switch and keep both connections active?
View 3 Replies View Relatedit's across 3 floors and the current setup is a single wireless router DIR655 (1st floor), but the WiFi suffers greatly on the floor below/above.
I have sourced 3x D link switches and 2x more DIR655's and would like to have all machines/consoles/phones etc in the household on the same network. Is it possible to keep one DIR655 as the main wireless connection and have the other as pure AP's as well as keeping the same SSID?
I have been testing WiFi devices such as the iPhones and iPads connectivity with the following setup:
1. 3502i AP
2. WLC 5508 SW 7.0.98
3. NGS
The i-devices have iOS v4.2
My goal is to have the guest user i-devices maintain the credentials (username and password) when they login again to the wireless network. Like if the device sleep, I think definitely they would loose those IP address issued by the DHCP. Once the guest user uses them again and connect them to the wireless network the user would not need to type-in those credentials on the Web Authentication page directed by the WLC.
The credentials are issued by the sponsor who created them on the NGS. It seems that there are WiFi problems with these i-devices. But somehow, I'm looking for a solution that would automated the logins like a checkbox if you want to be kept signed in, on Yahoo or Stay signed in for GMail.
Have a WLC 5508 running 6.x code with LAP's providing wireless for our internal laptops (WPA2 and EAP-TLS). I want to provide guest wireless which goes out a different port on the WLC to a guest firewall/cable modem. However, we want to prevent our internal laptops from being able to use the guest wireless. I have RADIUS (IAS) and LDAP for my AD available. We would prefer not to have use Lobby Ambassador and just have the guests use a simple password or web passthru. Guests may be laptops or smartphones. What options are available? I have tried a test setup using dynamic vlan assignments from RADIUS using the IETF flags, but can't seem to get it to work. Is there a way to identify the SSID is being used at the RADIUS server?
View 13 Replies View RelatedHaving problems with my wireless router, dropping and keeping connection active. For some odd reason I keep dropping connection either wireless or wired. I have a total of 5 items going through this router. 2 of them are wireless and the other 3 are wired. The wireless items are a desktop computer that is using the Wireless USB adapter to get online. Sometimes it drops and most of the time it doesn’t have any problems. I have a laptop that sometimes the connection goes from strong all the way down to no connection at ALL. It starts at 54MBPS to down to the RED X over the wireless manager. Forgot to mention both of these machines are Windows XP. If I reboot the laptop, it comes up without any problems.
Sometimes I tell Windows XP to manage the Wireless connection and tell it to disconnect and re-connect again, it goes. Now for the wired items, I have 2 gaming systems and another computer plugged directly up to the router. For some odd reason when I double click on the internet, on the computer that is hooked directly to the router, it says page couldn’t be found. I know that there is connection and there is nothing running in the task tray except for the Anti-Virus and Firewall. The browsers that I am using are Internet Explorer 8 and Mozilla Firefox 3.0.10. Also checked on the back of the machine to see if I have link lights and everything is flashing. Finally, when I click the homepage or refresh button about 2 or 3 times, it goes through.
think that I am overloading this Router and it can’t handle it. I might have to look into sending "Keep Alive" packet setting on the router.
We have a Linksys E1200 modem and I have been having problems with keeping my son from using the wireless interenet. I did change the password and that worked for about 24 hours and then he was able to get onto it again. He has a nintendo dsi and he is smart enough to figure out how to dismantle any parental controls on his gaming device. I think that he resets the modem in order to get back onto the internet in order to use his gaming device. Someone told me that you can register each item individually in order to keep kids from using it but I have no idea as to how this works. We have two iphones, a lap top, and two tablets.
View 7 Replies View RelatedI have a Cisco 877W-K9 router, and I for the life of me can not work out how to enable multiple SSIDs on the AP whilst keeping them all to the same VLAN?
I know this may seem silly but basically for our clients we setup WPA-Enterprise for one SSID and WPA-PSK for the other to help ease migration between the two etc, however all I can seem to do at the moment is create multiple VLANs and use ip unnumbered vlan1 to sync them all into one, but this seems really silly.
I switched from Time Capsule with AirPort to E2000 and have a problem with configuration.I use the same IPs as in AirPort and E2000 gives me an error:"The WAN IP address cannot be the same subnet as the Guest Network IP address" and I can't save configuration.But in my opinion they are different.I use "Static IP" option and I have IPs from my ISP: [code] So WAN IP is different subnet as LAN and I don't know what to do now. It worked with these settings in AirPort and here I can't proceed.
View 2 Replies View RelatedI am having an issue where occasionally the Sidewinder starts to see my internal RFC 1918 address instead of the configured external address of my firewall. This is for peering between the two. The error they see on the Sidewinder is:So instead of seeing the external peer address he sees a 10.220.3.18 address. We are not sure what triggers this becuase normally he see's my 63.117.98.222 address.
View 5 Replies View RelatedI have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 7 Replies View RelatedIs it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies View RelatedI have a Linksys WRT54GS v5.1 router running firmware 1.52.5.I am trying to use Linksys IP Phones SPA942, but these do not seem to be able to log on and just show "Initializing network" even though the MAC address appears in the router with an IP address.The strange thing is that I already have 4 SPA941 phones that work with no problem and just log on to the network.Is there something about the SPA942 that I need to configure differently, I have factory reset it with sucess, but still unable to log on to the network.
View 1 Replies View RelatedIs it possible using any module in CW to get the MAC address and IP address of all switchports on a 6500?
View 6 Replies View RelatedI have been trying to clone my PC's MAC onto my Linksys WAG120N adsl2+ modem router .
I click the the clone my PC's MAC button in the MAC address clone tab. I get the following error :
"Mac address cannot be the multicast address"
The MAC address starts with 1C:C1:XX:XX:XX:XX
I even tried to update the firmware.
I recently switched routers to the DIR-615 and I'm trying to troubleshoot why one of our laptops keeps losing the IP address and gets a self-assigned IP address. I see the following messages in the log, I am wondering if the reason codes are listed and explained somewhere? I tried searching the manual but could not find any information.
View 9 Replies View RelatedWe have an ADSL connection and use a D-Link DSL-320B modem. We have a D-Link DIR-120 router connected to this modem. This has worked perfectly fine up until today when we disconnected the router and connected a computer (call it A) directly to the modem because it was getting an unusable connection through the router for some reason. We later also performed a factory reset on the DIR-120 router.
Unfortunately, after the above steps the router did not receive any IP address (through DHCP) from the ADSL connection anymore. During my attempts to debug this I noticed that my laptop (call it B) didn't get any IP address either (when connected directly to the modem). I noticed the following syslog entries repeating over and over while trying to connect: [code]
At this point computer A could still get a connection just fine tho (when connected directly to the modem).
I then tried to change the MAC address of the router to an arbitrary one (a copy of computer B's MAC address but with the last digit increased by one). The router still did not get assigned any IP address. Finally I tried making the router clone the MAC address of a third computer (call it C). C has never been connected directly to the modem. Doing this worked. After cloning the MAC address of computer C the router is immediately assigned an IP address and the internet connection works as it did prior to all this.
Now, my question is, why would computer B and the original MAC address of the router not be able to get an IP address while two other computers worked just fine? Why would changing to an arbitrary MAC address not work while cloning the MAC address of another computer did? Could the router's MAC address have been blocked by the ISP for some reason (and what could cause this)?
but my situation seems more like a blacklisting of some MAC addresses rather then allowing just a single MAC address.
On my cisco IOS 12.4 router,Can i make it so only lets say mac address 11:22:33:44:55:66 able to use ip address 10.10.10.2?I want this so that only this IP can configure servers, and so if the computer using it is turned off, any other device cannot use the IP address.
View 6 Replies View RelatedI recently configured and installed a 1941ISR for a customer. The customer purchased a 25-User SSLVPN license with the router, and I configured it for remote SSLVPN access. This is working nicely except for one issue: when users initiate an SSLVPN connection request by browsing to the assigned webvpn gateway IP, they get the "There is a problem with this website's security certificate" browser message. They are in the process of working with their DNS hosting provider to get a DNS entry assigned to the IP address so the users won't have to specify an IP address in the URL address box, but they will continue to get the certificate error until/unless I can figure out how to resolve the issue.
I've tried the following "How to make IE8 trust a self-signed certificate in 20 irritating steps" that I found via another forum link but with no luck:
1.Browse to the site whose certificate you want to trust.
2.When told "There is a problem with this website's security certificate.", choose "Continue to this website (not recommended)."
3.Select Tools->Internet Options.
4.Select Security->Trusted sites->Sites.
5.Confirm the URL matches, and click "Add" then "Close".
6.Close the "Internet Options" dialog box with either "OK" or "Cancel".
7.Refresh the current page.
8.When told "There is a problem with this website's security certificate.", choose "Continue to this website (not recommended)."
9.Click on "Certificate Error" at the right of the address bar and select "View certificates".
10.Click on "Install Certificate...", then in the wizard, click "Next".
11.On the next page select "Place all certificates in the following store".
12.Click "Browse", select "Trusted Root Certification Authorities", and click "OK".
13.Back in the wizard, click "Next", the "Finish".
14.If you get a "Security Warning" message box, click "Yes".
15.Dismiss the message box with "OK".
16.Select Tools->Internet Options.
17.Select Security->Trusted sites->Sites.
18.Select the URL you just added, click "Remove", then "Close".
19.Now shut down all running instances of IE, and start up IE again.
20.The site's certificate should now be trusted.
I followed all 20 irritating steps to the letter, but am still getting the security certificate nat.Now when I “Continue to this website (not recommended)” and click on "Certificate Error" at the right of the address bar, the certificate error windows says “Mismatched Address”.Is there a way that I can get this fixed without resorting to a 3rd party CA?
I need to change the ip address on my router same ip address as myDlink router?
View 6 Replies View Relatedone of my friend can tell me my ip address by using gmail. He don't have any software to know the ip address. but he can tell me my ip address. how did he know it. is my wi-fi not safe? or other? and can we know it any way?
View 6 Replies View RelatedWhat is WAN IP address
View 2 Replies View RelatedWe have moved house recently and changed internet provider. The laptop and x-box have both connected ok. However the main pc will not connect. The wireless router says that it is connected but the icons of pc-router-internet is not connected. when you hover over the pc icon, there is no IP address.
View 1 Replies View RelatedHow exactly do you change your IP Address?
View 8 Replies View RelatedMe finding my friends IP. I know its not good finding others IP but i need that seriously.
View 4 Replies View Related