D-Link DI-524 - Computer Sees Wireless Network But It Won't Connect Even Wired
Jun 25, 2011
I'm desperately trying to set up my old D-Link DI-524 on my parent's Toshiba laptop...I'm visiting and going thru withdrawals! I've installed it, run the wizard etc but it doesn't work...not even wired. I've tried various cable configurations and I get nothing. Both cables are good and work just fine connected to the modem. I've reset it a few times, upgraded the firmware and still nothing...I'd think I'd at least get it to work hard wired. My laptop can see the network I set up even...but no data transmission. I'm not a wireless expert, but I need to become one fast!
So I have a WRT54G router since a couple of years now. Laptop (Win7 64bit), ipod, ipad, phones can connect to it without a problem, but new computer (Win7 64bit) can't. I can connect the PC via ethernet without a problem though.
I powercycled my devices, I changed broadcasting options off and then back on, changed my security mode, tried the MAC Cloning (after doing the MAC Cloning, I lost internet connectivity even through ethernet), resetted my security settings, changed SSID, I'm broadcasting through channel 11 2.462. I also tried deleting the HomeGroup
Important fact: the network is in the list of available wireless network, but Signal Strength is No Signal and I can't connect to it. My network adapter is ASUS 802.11n Wireless LAN Card, drivers are up to date. I've upgraded to the latest router firmware.
I have a Linksys Wireless G Model WRT54G2V1 using WEP encryption. I recently added a laptop. It can access various non-decured netowrks. It can see my home network but is unable to connect despite entering the correct passcode. how to get the laptop and secured network to communicate?
Have Win 7 on a desktop and laptop. Tried several ways through network wizard(novice on PCs) to setup network and no internet connection with either unit. The router sees the internet and the laptop picksup the network I setup but can not connect on either PC. I know I don't have a setting write and I do not know where to start again or what specifically to look for. We just want Internet on both PCs.
1 newer build computer connected to D-link 655 via Cat6.1 laptop computer connected to same D-link 655 via Wireless N minicard. (Intel) (130Mbps connected) Router on a 10 foot shelf, always have full bar in wireless strength on 2nd computer.
Both computers can upload and download as expected from the internet. Transfers between the two computers though are slow. Both computers are loaded with Windows 7. Transferring files to or from the laptop transfers at 1.5MB/sec to 2 MB/sec.
My computer is a 32 bit, Win7 SP1 with Pentium Dual Core 2.6 Ghz and 2Gb of Ram on a wired network. My wife has a similar system using a wireless network. She can ping my IP Address, but I cannot ping hers. We both have full access to the Internet. We are using the same workgroup, and both computers have file and printer sharing enabled and IPv6 addresses and DNS server addresses selected automatically.The problem appears to be with my computer?
Here are my system stats:
Tech Support Guy System Info Utility version 184.108.40.206 OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 32 bit Processor: Pentium(R) Dual-Core CPU E5300 @ 2.60GHz, x64 Family 6 Model 23 Stepping 10 Processor Count: 2 RAM: 2013 Mb Graphics Card: Intel(R) G41 Express Chipset, 782 Mb Hard Drives: C: Total - 76308 MB, Free - 49226 MB; D: Total - 286167 MB, Free - 52893 MB; M: Total - 38154 MB, Free - 7 MB; Motherboard: ASUSTeK Computer INC., P5G41-M LE Antivirus: Microsoft Security Essentials, Updated and Enabled
Installed E4200 with an iMac running MacOS X Version 10.6.8. Wireless connection works great. Also connected a wireless laptop without a problem. But can't connect a 2nd computer is wired. That is a PC running Vista. I know the wiring is good, because the E4200 is a replacement router in a network that was working fine.
I have a Belkin F5D8636-4 v2 N Wireless Modem Router. For some reason, it will only connect to the internet if the wired computer is plugged in and on. I tried starting the router without it plugged in and it kept trying and failing to connect to the internet. As soon as I plugged in the wired computer it connected to the internet. jhb019 has chosen the best answer to his/her question.Click here to view the answer that was selected.
I have a wireless network in my home. I reliably get solid connections on our various devices such as the Wii (netflix streaming), a net book, a laptop and Wi-Fi connections on android phones. When I first set up the 930L I thought it was defective because I couldn't get a connection. Until I did it in the same room as the router okay, that worked. But I move 2 rooms over and I no longer connect.
Seriously, I can go a few rooms away and easily stream an HD movie via netflix to my net book. But if I set up the 930L at the exact same location it will not connect. If I move the camera within about 20 feet of the router with only maybe 1 wall between them, it will connect.
At this level of wireless power it is nearly worthless for me. Is my camera defective or are all of them this lower powered?I am running a dlink router, 300N, WPA security. Like I said, I can connect if I'm literally 10 feet away. But any significant distance or anything more than a single wall in between and the router no longer sees the camera. And all other wireless devices have strong, reliable connections all through my house.
I am with Virgin media (UK) and have the 20mbps fiber optic connection. My area has recently been having problems with the broadband and Virgin has recently fixed these problems. However I used to get around 19mbps now that the problem is fixed my computer which is wired to the router gets about 0.4mbps downstream... However the 5 wireless computers all get 16mbps which is pretty good for them. Windows tells me that its a firewall issue and I currently can't use two programs, spotify and steam. They both have firewall issues, even if I turn off my firewall which is the windows one. I also have avast, and when I turn that off, still no good. I used OpenDNS, stopped using that flushed my DNS, that didnt work. I tried to optimize my computer settings, by changing various values in Regedit.All of this has done nothing. I should add that I have recently re-installed Windows 7 so on this fresh install it has never had decent internet speed. Which I thought was weird.. I have basically had these problems since the fresh install. All of my drivers are up to date.
have a computer that connects to the internet via a wireless network connection. The router to which it connects is not physically available.I have a device that I want to connect to the internet. However, it is a wired device. The device cannot reach the wireless router that the computer connects to.Is there any way for the wired device to connect to the computer as an intermediary? The computer has a built in wired network card (as well as a USB wireless device that connects to the wifi router).
I've been using D-Link DIR-600 wireless router for two months with my ISP, SmartBro. A week ago my internet went down due to heavy rain and technical support had a home visit yesterday to re-activate my internet connection. My net connection came back smoothly using a direct connection from modem to laptop.When I tried to connect the modem to my wifi router, the internet was not detected. Even if I reset the router settings, no internet connection was detected. Initially, I thought there is a problem with my wifi router so I connected the modem to our Edimax wired router but still it could not detect internet access. Every time I open a browser while connected to a router, this message is shown (see attached screenshot).
I tried using another ISP, Wi-Tribe with both wired and wifi routers and everything worked well. So now I assume the problem lies with my SmartBro ISP. I called the ISP hotline but they told me that they do not provide support for router connection problems; only with single, direct connect to a PC.I asked a neighbor IT technician to look into my problem but he too could not solve the problem.
I have a wireless router (TP-Link) which I want to use to extend my wired dorm room cable connection.The "blue" network cable currently goes straight into my laptop and I have no control over its configuration.Is it possible to plug the blue cable into the WAN port of my router and then wire the computer back into a LAN port?BUT that's not really the major problem. Mainly I would like to know how the router must be configured to allow me to use other wireless devices in my room (phone printer etc).Someone told me that I "just" need to use the "bridge" setting but that turned out to be complicated by warnings and messages about other SSIDs.Is "bridge" really the right mode? It seems it's for connecting two wireless networks together.
MY ISP is AT&T. I have their Westell DSL modem, with a bridged connection to a Linksys wireless router. The router is connected via ethernet to a dead computer: a 7 year-old Dell desktop that will boot up but shut down right away. I have been able to connect multiple laptops wirelessly to this network. I thought an ethernet connection was required in a home network such as mine? The cable has been plugged into a dead computer for several months and frankly I'd like to get rid of the desktop. What exactly is the ethernet requirement - just to be plugged into a port? Could I theoretically just yank the ethernet card out of the desktop and use it instead of the whole dead system?
Region : Canada Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP :
Just got my new TL-WDR4300 router. Set it up last night with the latest firmware. I can connect to Internet using a wired cable. However, I can't connect to Internet via wifi. I already tried 2 laptops (Vista & Win XP) and 2 tablets - I can see my wifi signal, connect to it (with my password), even obtained IP address (from ipconfig). However, when I tried to open a web page (eg google), it can't connect to Internet (always got timeout or service not found). Again, same laptop has no problem if I use a cable to connect to my router.
Region : Indonesia Model : TD-W8151N Hardware Version : V3 Firmware Version : ISP :
Recently I bought TD-W8151N wireless adsl router, I have one desktop computer that connected to TD-W8151N via ethernet and wirelessly to one laptop, IP Addr: 192.168.1.4, Subnet 255.255.255.0 and Gateway: 192.168.1.1 : desktop (LAN connection IP Addr: 192.168.1.3, Subnet 255.255.255.0 and Gateway: 192.168.1.1 : laptop (wireless connection) but I can't ping each other and also can't access the share folders between them., both computers can access internet. Is there anything I missed the configuration setting of the router? Before I use wireless, I connected this 2 computers using cross-type utp cable, and working good.
I'm trying to re-setup this EOL camera on a new router.I've been able to reset the cam to factory defaults and see it wired using dhcp. I then was able to change the address to a static address, still wired and still can see it with IE. However when I disconnect the rj-45 cable, power down and restart, I can't access the cam.
I have a dell desktop running windows vista that connects to my wireless router with a cable. I have an HP laptop that is running windows 7 that is wireless.When I look at network computers on the dell I get an error message that says that the computer is not accessible. The same thing happens when I try to log onto the desktop from the laptop. When I try to run the network wizard from the desktop, I see see connect to the internet, connect to a wireless router or access point, setup a dialup connection and connect to a workplace.None of them make sense but I tried connect to a wireless router and got a message that said to set it up manually or set up a flash drive, neither of which makes sense. I tried set it up manually and all that happened is the router setup screen opened up.I tried the same thing on the laptop and the setup the network wizard opened a screen that said choose a wireless router or access point to configure, but nothing ever showed up on that screen.
The netbook was working fine on wireless network; didnt use it for a couple of days - now I cannot conenct wired or wireless; cannot see the wired or wireless modem , only MSN dial up. But the wireless modem light is blinking steadily. Otherwise the netbook is working OK - it even seems to boot up quicker than it used to)(I would reinstall the OS but it didnt come with OS DVD or a DVD drive ; so I didnt create a backup when I bought it. I have since purchased a USB DVD drive; this is one of two identical netbooks I purchased on black Friday - other one works perfectly?
My laptop is the E6420 and I cant connect to the Internet, the little wireless icon doesnt even show up in the taskbar. tried to set up a new network, didnt work, it says the modem's been removed. but no other info.
My Windows XP computer cannot connect to the wirless connection. It used to work before but we installed a new router in our home when I try connecting to the network, it tries to connect but it refreshes and doesnt connect to the internet
I have a wireless network. For some reason my computer seemed to change regarding the settings, and I can't figure out what to do. Usually I can figure things out when the settings go wrong. I have a broadband connection, where it seems to want me to enter a phone number; I have a "LAN or High Speed" connection. Normally I click "Create New Connection", but it doesn't work.
I have just moved apartments and am trying to connect to the internet. The problem is that I can see the network I need to connect to and I am putting in the correct network key but it just won't let me connect to it. There are three other computers using the wireless so it isn't the modem... and my iPhone is working on it. I am wondering if it has something to do with the IP... I do not really understand any computer stuff but I am desperate for this to be fixed because I am in the middle of mid-terms.
I'm having trouble connecting my 360 to the wireless router to gain Internet access.I use my phone's Wi-Fi to gain internet access with NO issues. My current setup: NetGear Wireless router is connected to my D-Link wired router, and I can access the internet no problem. (10 MBPS down, 5MBPS up)When I try to connect the 360 to the Netgear Wireless router, it connects to the Network, but Internet test it reads "DNS error - The router or modem may mot be automatically providing DNS settings. Try a manual DNS setting instead."(Next suggestion) "DNS Error - If you have a PC that can successfully browse the web, check it's network properties to find the DNS address it uses..."Now, I have XBMC running on my computer, and the 360 can access the network so it shows up under Video Apps so I can see a file list to stream movies. When I try to run a movie, it says I must download an update - so I can't watch the movies at all.I juso set it up so I can access the Network AND Internet.Again, Netgear wireless router (which 360 connects to) connected to D-Link wired router.
I'm sure it's on here but because I dont understand the name of what I'm looking for, I'm having trouble searching. My main network is setup for wireless via a netgear wndr3700. I'd like to use my old linksys wrt54g v5 to connect to that network wirelessly and allow me to connect my xbox via wired ethernet. Basically instead of buying a wireless adapter for the xbox, i'd like to know if/ how i can use my linksys router instead.
somehow connecting my PC to my home network as if it was wired. Having a wired connection just won't work because my PC is far away from my modem and router. The reason I want to connect it wired is because I am getting terrible speeds, and the slowest. [URL]