Cannot Connect To The Same Network With Wired And Wireless Computers
Nov 2, 2012
I have a dell desktop running windows vista that connects to my wireless router with a cable. I have an HP laptop that is running windows 7 that is wireless.When I look at network computers on the dell I get an error message that says that the computer is not accessible. The same thing happens when I try to log onto the desktop from the laptop. When I try to run the network wizard from the desktop, I see see connect to the internet, connect to a wireless router or access point, setup a dialup connection and connect to a workplace.None of them make sense but I tried connect to a wireless router and got a message that said to set it up manually or set up a flash drive, neither of which makes sense. I tried set it up manually and all that happened is the router setup screen opened up.I tried the same thing on the laptop and the setup the network wizard opened a screen that said choose a wireless router or access point to configure, but nothing ever showed up on that screen.
Our wireless clients that connect through our AP541N cannot see other computers on the network. They can ping other computers by IP and host name and access the internet OK. Mapped network drives can be connected initially but are very unreliable and always end up disconnecting. Restarting the computer does not work. When these computers are wired they see the network as expected. why my wireless network would behave differently then the wired? The wired and wireless networks are on the same VLAN. The wireless clients are all Windows 7 systems.
I use a Ethernet Powerline adapter.Right now, there are 5 other computers on my wired network, and i don't know what they are. What are they doing there, and how do i get them out?
I'm sort of new to networks so I'm not sure if this is even possible but what I'm trying to do is set up a wired network between computers but leave the wifi on the computer as how it connects to the internet. I'm using two computers connected through a lynksys router(not connected to the internet) and ethernet cable, and one of the computers has a wireless card that connects to another router that is connected to the internet. i can set up a network between the two computers but then the one can't connect to the internet(even though it says it is connected the network with internet),
I have set up a wireless network in my home using s d-link N+ 300 DIR-655 and the desktop that is directly connected to the modem and router can connect to the internet and my laptop can access the wireless network and get online but I have another desktop that cannot connect to the wireless network. It can see it but when i try and connect i get the message that it was unable to connect or sometimes that i was able to connect but have limited connectivity.
The facility provides WiFi access. I'd like to configure his router to access the facility's WiFi, as WAN access to the internet while providing DHCP service to the wired ports. The idea is to use the 4 wired ports to provide inter-connectivity to each other and internet access via the router's wireless connection via wireless for internet access by the wired client machines.I'd also like to firewall the wired devices from access by other users of the facility Wireless network.Can I do that? How do I configure the wireless aspect of their Belkin Share 300N? What other settings do I have to set.
I have a Windows 8 Pro laptop, and a new Windows 7 Laptop. When I try to setup the connection so that I can share files and folders between the two computers, I am asked for the User name and the password. I see the password in the homegroup, but entering it does nWhat is the user name in this case? My computer name or the other computer name or something else
The netbook was working fine on wireless network; didnt use it for a couple of days - now I cannot conenct wired or wireless; cannot see the wired or wireless modem , only MSN dial up. But the wireless modem light is blinking steadily. Otherwise the netbook is working OK - it even seems to boot up quicker than it used to)(I would reinstall the OS but it didnt come with OS DVD or a DVD drive ; so I didnt create a backup when I bought it. I have since purchased a USB DVD drive; this is one of two identical netbooks I purchased on black Friday - other one works perfectly?
My laptop is the E6420 and I cant connect to the Internet, the little wireless icon doesnt even show up in the taskbar. tried to set up a new network, didnt work, it says the modem's been removed. but no other info.
I'm desperately trying to set up my old D-Link DI-524 on my parent's Toshiba laptop...I'm visiting and going thru withdrawals! I've installed it, run the wizard etc but it doesn't work...not even wired. I've tried various cable configurations and I get nothing. Both cables are good and work just fine connected to the modem. I've reset it a few times, upgraded the firmware and still nothing...I'd think I'd at least get it to work hard wired. My laptop can see the network I set up even...but no data transmission. I'm not a wireless expert, but I need to become one fast!
I'm having trouble connecting my 360 to the wireless router to gain Internet access.I use my phone's Wi-Fi to gain internet access with NO issues. My current setup: NetGear Wireless router is connected to my D-Link wired router, and I can access the internet no problem. (10 MBPS down, 5MBPS up)When I try to connect the 360 to the Netgear Wireless router, it connects to the Network, but Internet test it reads "DNS error - The router or modem may mot be automatically providing DNS settings. Try a manual DNS setting instead."(Next suggestion) "DNS Error - If you have a PC that can successfully browse the web, check it's network properties to find the DNS address it uses..."Now, I have XBMC running on my computer, and the 360 can access the network so it shows up under Video Apps so I can see a file list to stream movies. When I try to run a movie, it says I must download an update - so I can't watch the movies at all.I juso set it up so I can access the Network AND Internet.Again, Netgear wireless router (which 360 connects to) connected to D-Link wired router.
I'm sure it's on here but because I dont understand the name of what I'm looking for, I'm having trouble searching. My main network is setup for wireless via a netgear wndr3700. I'd like to use my old linksys wrt54g v5 to connect to that network wirelessly and allow me to connect my xbox via wired ethernet. Basically instead of buying a wireless adapter for the xbox, i'd like to know if/ how i can use my linksys router instead.
I just loaded up my machine with Windows Vista Home Basic and wanted to connect my another laptop to it via Wireless AdHoc network. I created a wireless adhoc network from the network and sharing center. But was unable to connect the other laptop to it. Everything is ok. My WLAN is on, drivers are also latest.[code]
I have an hp g62 laptop and it has an Atheros ar9285 wireless adapter and a realtek pci-e ff ethernet adapter. For some reason just recently neither will connect to my netgear cable wifi router. I have two smartphones,xbox and two other laptops that connect with no problem. Everything is configured correctly that i can tell and both drivers have been updated. still nothing, it trys to connect but keeps saying identifying then it says no internet access. also i have disabled firewall and entered the security paraphrase twice just to make sure.
I'm trying to connect my two computer (XP and Win 7) using a crossover cable. I set the the IP as 192.168.0.1 and 192.168.0.2.The computers can see each each other and I can access the public folder of the win7-machine on my XP-machine. However, if I try accessing the xp-machine it says:
I have had a netgear router for some time now (WNR2000) for three home computers, all Windows Vista+ and recently had to buy a new wireless adapter for one of them (WNA3100). Previously, all computers were connected to a security-enabled network called 'Johnson'.I installed the new adapter via the wizard and it ended up creating a new network entitled 'NTGR_zhOXSTT8ZSXtTUsaRd5lXfrq-WPS'. Johnson has now disappeared from the list and no other computer is able to connect to this new network. I tried changing from WPA2 to WEP and changing the password in hopes that the other computers will be able to login but it didn't work.
I've been using "Linksys by Cisco Wireless-N Home ADSL2+ Modem Router WAG120N". I can restrict internet access to only 8 computers using their Mac adresses but there are no ore entry fields for Mac adress than 8. What shall I do when I need to block internet access to more than 8 computers say 20 computers on wired LAN? I don't like the option blocking the internet access via IP address. I found they are not that effective as the option Mac adress
We have a customer which is using ISE with 802.1X in order to authenticate computers. All the computers have their own certificate and most of them can be authenticated fine! The issue is that some computers cannot be authenticated.The port configuration the authenticator (Cisco WS-C4510R+E IOS 151-1) are configured exactly the same: [code]
But for some reason some PC cannot be authenticated. A wireshark capture on the computer not working shows that the computer receives a EAP Request Identity and also send a Response Identity to the switch but then nothing happens more: So the process is stucked in the EAP-Response/identity. I attach a debug capture on the switch for one of the computer which cannot be authenticated.
is it possible to connect between 2 networks (different ips)? i have a wired ethernet group n a wireless group, my printer is on the wired group, my laptop on the wireless one.
I just brought my new PC build over to my grandmothers house and I can't connect to the internet on her connection. All I did was plug her Ethernet cable into my port on the back of my motherboard. I didn't touch any other cables or settings. It seemed to recognize there was a connection but said it was public and was trying to identify it. Then, I was unable to connect to the internet.
I've got an RV042 router at home and am connected from my office via the QuickVPN client ver 1.4.1.1.2. I can ping the RV042 and log into the administration page and make changes. However, I can not see other computers on the remote network. I can not ping them. When I open my Network page, I still see the computers on my local network.
All machines are running Windows 7 Ultimate. ISP is Comcast at both locations. WAN IP's are dynamic, but have not changed in over a year. Local IP's on the remote (home) network are static..[url]....
It all happened pretty suddenly, from 1 day to the other, suddenly i was unable to connect to my home network. I started to troubleshoot, search forums etc. But no luck. I triedand look for the problem myself and found that thenetwork was enabled but it stayed on "identifying network". By clicking buttons from here and there on thecontrol panel i found something like a network recognition or something like that and a yellow little prompt appeared on the top of the explorer saying something like the network idetification was disabled, so i clicked and selected enable but it prompted again, so i just entered to the advanced network recognition center and noticed that on the public and private tabs netowrk recognition was disabled, so i clicked enable on both and saved changes, but the changes dont save, its like if i wasn't on a administrator account (but i had no error messages, it just wont enable).
I have successfully configured my Cisco RVS4000 for VPN Access, and Installed QuckVPN on my client machine. I can connect using QuickVPN no problem, but I cant access anything on my network. When I try pinging any of my servers I am unable to do so. I can ping my gateway thats about it.
I have a home wireless network and my service provider is Suddenlink. I use a DLink modem and have two Tosiba laptops. All of this has been working fine until this morning when one of the laptops won't connect to the internet. when I run the trouble shooting guides on it I get messages that the problem is that the modem won't connect to the internet. However, the other laptop (this one) is working fine. when I look at the network map i see both computers and a green line to the modem. on this computer, there is also a green line from modem to internet. the other computer shows a res x on the modem to internet line. this is a sudden change i have restarted the computer the modem and the router. I can also conenect this computer to the internet via a mifi that I have but not the other laptop. there are no red x's on any of the hardware when I go to the "manage" computer.
DSL Internet Router (Dynamic IP) -> Linksys RV082 -> Firewall PC -> LAN
DSL Internet Router: 192.168.3.0/24 Linksys RV082 WAN2: 192.168.3.0/24 Linksys RV082 LAN: 192.168.5.0/24 Firewall (2 Nics): Nic1 is 192.168.5.0/24 and Nic2 is 192.168.1.0/24 LAN: 192.168.1.0/24
RV082 WAN 2: Configured with a DHCP IP Address from DSL Internet Router so it has 192.168.3.0/24 range IP. Load Balancing enabled Static Route added on RV082: 192.168.1.0 mask 255.255.255.0 gateway 192.168.5.x interface LAN Firewall PC is completely Open as i was using it before.
I had a Fortgate 60B and everything worked fine, then a bought a RV082 and now i can get this up and running properly.The thing is this....whit the actual setup i have, computers only can navigate through HTTP web pages, other ports seem to be closed, but if the Firewall PC was blocking this i guess i'll know because it shows a message on screen when a policy is being applied. If i try to open HTTPS Pages it doesnt work, Even a simple pinng to google.com doesn't work from my LAN (192.168.1.0/24), but if i connect a computer on a local port on RV082 i can PING and i can browse anywere i want.
It seems to be that Firewall PC is causing problems but i execute a tracert to [url]...., the packet get stuck in the RV082.What im thinking is that maybe the RV082 doesn't allow to go trhu at all if the traffic comes from other networks that doesn't belong to the one configured on its LAN side.By the way the Firewall PC connected to the RV082 directly navigates perfectly.
PS. The reason im using Firewall PC is because that way is much easier and flexible to handle policies for Internal users than in the RV082 Router. I use this ume basically to set up VPN IPSEC and Dual WAN Load Balancing.
I cannot connect to a PPTP on the outside of my network.We have a RV082, port 1723.It says verifying username and password but then disconnects.The error log says Blocked IP Spoofing.
just got internet today and set up the wireless on the router using a laptop connected through LAN. All computer now connect to the router through wireless except the the laptop that was used to set it up.
i have a laptop and a desktop, everything was working fine until i messed with something in the router settings by accident, i changed some type of security setting and then changed it back because i was testing something.. at this point i had to remake the network for some reason, whcih was no problem i put in the pin and security code and i was able to connect through my desktop with no problem.. a few hours later i realized my laptop could no longer connect.. i recieved the unable to connect error.. i read that it could be the security settings, so i assumed i switched something before by accident and i restored to factory defaults...
after i did this my laptop could connect to the internet but my desktop couldnt connect! so it basically reversed itself.. i dunno what could be the problem.. i tried 2 of the 3 authentication modes because i am afraid if i try the 3rd i will lose internet completely then i will have no clue what to do..
