Just replaced my old di-524 with dir- 815 and now i have very slow internet ,LAN and wireless,if i hook the di-524 back up internet is back to normal was
going for faster internet and more wireless range.
I'm currently subscribed to Comcast's 22/5 Internet service. Internet upload speeds on both wired and wireless are about the same at ~ 5 Mbps. Wireless download speeds range from .5-3 Mbps. Wired or Wireless, I receive LAN speeds of ~32 Mbps or 3-4 MB/s. The noticeable issue is wireless internet download speed. I have tried every configuration possible with my router, updated drivers on devices, firmware and tested everything I could on all PCs, and even used the XBOX 360's media extender network tuning feature as a tool in my investigation to find this bottleneck. All reports point to internet download speed. Again, general LAN and internet upload speeds relatively meet expectations. The wired download speeds are slow at times, but consistently meet expectations.
My current Setup:
Wifi
A4 1.33NA
WPA2 Only - Personal
802.11 Mode : 802.11n only
Channel Width : 40MHz
Channel : 1
[code].....
Region : Brazil
Model : TL-WR841ND
Hardware Version : V7
Firmware Version : 3.13.9 (Last)
ISP : NET Virtua
I've bought a TL-WD841ND and was using it normally.
After I arrived from a trip, the internet speed by wireless and by cable is only 0,5~0,7 Mbps...
My internet connection is 10 Mbps, and if I plug direct on the modem, there comes the real speed (9,7 Mbps), but connecting by the router, the speed is 1/20 of what should be. Before my travel i was using it normal, and no one has changed any configuration.
So i've updated to the last firmware avaliable on the website. So i've rebooted it and the "configuration" LED keeps flashing...
I would like to know if this led flashing is normal: (here is a video that i've done: [URL] and what could be happening. ps: connecting by cable, the internet speed is also the same (even after the factory settings reset)...
Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
Region : Netherlands
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
ISP : Ziggo
I currently have a issue with my TP-link WR941N.When I first connected the router I had a good internet speeds of about 70 mbps. My max provided by the ISP is 120Mbps but 70 was acceptable for me. Recently however the connection is terrible. I regularly have a speeds of 6Mbps via the router, When i directly to the modem via kabel I get a speed of 120Mbps. Therefore I ruled out that the connectivity problem is due to my ISP.
Yesterday, my linksys router broke down suddenly. I went to the store and bought a new one, a d-link DIR-615. After plugging it in and setting it up, i tried loading web pages and it worked ok. It wasn't as fast as my linksys router but it was fine. When i tried loading youtube videos, that wasn't the same story. The videos didn't load. It started playing but then stopped after a couple of seconds. When i connected my computer directly to the modem, the videos loaded fast. There seems to be something wrong with the video streaming.
View 9 Replies View RelatedI have been using my DIR-655 for about 2 weeks now with Road Runner wideband services. Starting yesterday my internet became very slow and I discovered the cause was the router. I tried resetting it to factory settings and things will be fine and run smoothly for about 5-15 minutes but after that it goes back to being extremely slow. My speed tests would go from 10ms (normal) to 250-450ms. Before this issue occurred the Dlink was perfect, had full speeds. I am running a wire Ethernet connection.
I am currently using revB and tried upgrading firmware to 2.01NA which had no effect, but make my internet seemingly go back to normal for the first few minutes then nosedive again.I have also changed my speed/duplex settings in Network Config to 1gbs Full Duplex. I've also disabled QoS, and still no change. Not sure what else to do.
When directly connected to the modem everything seems fine. The modem is also the provided Motorola SBG6580 which I have called Time Warner to set the modem into bridge mode and have the DIR-655 connected to it.
With DIR-655 connected to PC
With Modem connected to PC
Okay i just got the DIR-615 N Router and at first i was getting 40 ping on speedtest.net but now I'm getting 360 ping which is really frustrating since i upgraded because my old one was having troubles and also when i get to the check connection in the setup i am getting Your new router does not appear to be connected properly.
View 3 Replies View RelatedRecently I have noticed my internet get slow. I use a comcast cable internet connection that is directly connected to my dlink DR 655. I use the megapath internet speed test [URL] when testing my internet speed. Have a laptop that is usually on wireless and an XP workstation that is connected to the 655 directly with static IP.
I would be browsing the internet and all the sudden the internet would get really slow. This would happen on both my desktop and the laptop and my speed test on both machines would be around .3 Mbps. When this happens I would go and connect the laptop with the ethernet pot directly to the modem. Of course a reboot of the modem has to occur before a connection can be made so once I do that all the sudden my internet is back up to par (12 Mbps). I go ahead and put my network back to the way it was and it all goes back up to 12 Mbps. I have called comcast several times and they are telling me it my router.
This picture shows a snapshot of some windows from the laptop. The CMD ipconfig on the bottom left shows the laptop network settings when connected directly to the modem. The CMD ipconfig on the upper left is the network settings when connected to the router. The web page on the right shows the WAN network settings when the 655 is connected to the cable modem.
Notice the DNS servers, they are different when the 655 is connected to the modem versus when the laptop is connected to the modem. Could this be part of my problem? I have not seen were I can manually change 655 DNS entries ... is there a way to do this? Or should I not even be worried about it?
I upgraded from Vista 64 bit to Win 7 64bit and one of the first things I've noticed was that youtube videos take forever to load, I use to stream on 720p videos in realtime but now even 360p can struggle to load, 480p videos you have to pause for 30 seconds. Oddly, speedtest indicate my full 15mbps down and 1mbps up, regular downloads go fast but streaming youtube, vimeo, or anykind of videos take a while.
My initial guess was that it has something to do with the Wi-fi PCI card. I have D-Link dwl G-550 and on windows compatibility center it says its not supported. Windows 7 automatically detected and installed its own drivers, it works ok.
This only started about a week ago and everything was working fine before then. My router is causing my internet to be slow (I know this because it goes at normal speed when I am connected directly to my modem)
View 1 Replies View RelatedI`m new here I recently purchased the dir-615. I started configuring with cd but i couldn`t get past the step where it should verify if cables are plugged in , so I did it manually. Some pages won`t load , internet speed is slow ( Both wireless and lan speed ) . I am using a PPPOE connection , I even got my ISP to check my settings, and he said it was alright but it reduces my speed by a lot. Usually I download with 1 MB/s with the router on wi-fi I hardly get 50 kb/s and on lan max is 100 kb/s.
View 1 Replies View RelatedI have recently bought a TP Link wireless usb adapter (TL-WN727N). Initially I had some issues with drivers but solved that and my internet was working perfectly for around 2 days. However recently the internet speed has dropped down to extremely low speed periodically for no apparent reason. I can be downloading something at around 700kBps one moment then only have 100B/s the next. [CODE]
View 3 Replies View RelatedI have recently had trouble with my wireless D-link WBR-1310 Router. Two days ago everything was working fine, my wireless connection from the router to my macbook was fine and the wired connection to my desktop pc was also fine. I went to bed and when I woke up the next day everything was still ok. About 3 hours after I had first turned on the PC that next day my wired connection started spiking and dropping connection frequently, maybe every 5-10 minutes or so. I play world of warcraft and I also use Mumble VoiP Program and my pings in both are over 800 constantly now making it impossible to stay connected to either program. Sometimes it will drop down to regular numbers (25-50ms, I play on eastern servers as I am in NY) but then rapidly jumps back up into the 1,000's. My wireless connection is still fine though nothing has happened to that, only my wired connection is messing up.
I've tried changing my speed and duplex settings on my onboard NVIDIA nForce 10/100 Mbps Ethernet which is what im using but it hasn't worked. When connecting directly through the modem the problem seems to stop so its definitely the router.
Wireless Router: D-link WBR-1310
Hardware Version: B1
Firmware Version: 2.02
[Code]......
Just got my fiber Internet 100/100mbit and connected it to the D-Link Dir 655 AP. I only get about 30mbit out of it. I've scanned and tried to change to channel 1, 6 and 11 with no luck, same speed. There is no electronical devices between the AP and the PC. When i go into task manager in Windows, it says i'm connected to the ap with 130mbit. I got the latest firmware.
View 14 Replies View RelatedI got a new DIR-655 RevB today, and set it all up. It works fine right now in terms of speed, but certain websites (specifically, facebook.com) load very slowly on wireless. I've tried on two computers with different browsers / operating systems and it still loads slow. I also have comcast which I use a linksys router with, and it loads instantly. Connecting through wired works. Also, I get no slow down when connecting wirelessly if I use a VPN. When I do a speed test, I get my full speed, so that's not a problem.
A few things I have tried:
-Changing the wireless channel
-Disabling QoS
-Disabling traffic shaping
-Changing DNS servers
-Transmit only N/G
-Reducing MTU size
-Disable Dynamic DNS
-Disable advanced DNS service
-Connect to facebook through SSL and not
-Turning router off and on again
Also as a side, unrelated problem, whenever I enable a few ports to be forwarded, I can't connect to the internet when either wired or wireless?
Just bought a new DIR-655 Xtreme N Gigabit Router 3 days ago. Have 5MB fiber and consistently receive 4.7-5.0MB when connected directly to my laptop (windows XP, Dell wireless 1390 WLAN Mini-card, 802.11g only). I followed the CD instruction to set up the router and when connected wirelessly I consistently get 2.4 - 2.7 MB. When I connect a cable from the router to my laptop, I get the 4.7 - 5.0MB that I get when connected directly. I've tried a second laptop (Vista, 802.11g only) and when connected wirelessly I get 4.7-5.0 MB. A friend of mine who has a laptop (Windows 7, g/n) also connected at 4.7-5.0 MB.
View 1 Replies View RelatedHaving some issues with my wireless connection which only seem to occur after 12-1AM, my signal according to windows 7 seems be lowered which results in anywhere from 2-10 seconds stall in service, sometimes even disconnecting me all together.
I get no issues during the day of any sort where i have 4+ other devices constantly using the router but I'm the only person in the house that uses the internet this late in the night so I'm completely stumped on what the problem could be.
Using the Dir-655 router with B1revision with 2.0 firmware, connected with an older wireless G adapter.
I originally installed my DIR-655 as a wireless access point, not using the wired ports at all, and it worked fine like this. Trouble with my trying to set up my Bell router/modem with port forwarding prompted me to change my configuration so my Bell router /modem is now only a modem, and I am using the DIR-655 as a wired as well as wireless router. I have a separate network server and so don't use the DHCP on the DIR-655, and I only use one port to connect to a separate gigabit switch that serves the network.
I am finding that the wireless connection works really well with the few wireless devices I have connected (mainly an apple tv, and a MAC book) but my wired connections to the internet "feel" slow, sometimes with a significant delay before links to sites are established. I click a link, and wait for several seconds before the site shows up in the browser; sometimes after that the same site seems to respond at normal speeds, other times there are added delays.
Is there something in the DIR-655 settings that would cause this? The wireless connections seem fine.
Should I be looking at a new router/modem (rather than separate boxes)? If so what would be the equivalent D-Link model?
I am using a DIR 825 and I experience slow data transfer speed within my internal network under the wireless connection (2.4 Ghz), 2 Mbs. I can videostream from the internet OK, no problems there, but when I want to transfer data between two external HDD (NAS devices) it can get as slow as 2 Mbs.
View 1 Replies View RelatedI recently changed internet provider and rented a D-Link N 300 Router. On most days everything works well. However on some days the internet connection on my new laptop that has Intel Centrino Wireless-N 130 network adapter get really terrible (usually on Friday and Saturday). At first I thought that the problem was with provider, but now I find out that my old laptop that does not support 802.11n (only 802.11g) has excellent internet connection (at the same time when the new laptop struggles).
How can I troubleshoot what is causing this problem - the laptop network adapter or the router? Is there some setting for network adapter to force using 802.11g?
My laptop is running Windows 7, if that matters.
I recently bought a new TP-Link TL-WR741N, I'm transferring data from my desktop wired network, windows 7 to net book windows xp wireless. i'm getting only 2 mbps.
View 3 Replies View RelatedJust bought a dir-655, set it up (all though the wizard wasn't working, it kept getting stuck on step 5 of 7) so I just configured everything manually.I'm getting 2.4 MB/s speeds wirelessly.I was expecting much better, my wireless g linksys router did just slightly lower than that. My xbox 360 can't even stream HD without buffering every few mins. It also will just stop, and be unable to see the media for a couple minutes (when doing HD).I have wireless setup as WPA2, and the devices I use wirelessly are N devices. I have the router setup to only use wireless N.
View 14 Replies View RelatedRegion : Netherlands
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 130129
ISP :
I've this dualband wireless router since a week.Now I found out, NFS is working very slow (actually NFS is not working at all).I have a Mede8er and a synology NAS server connected to the TP-LINK WDR3600 router.I have movie directories shared on the NAS using NFS.when I go to the NFS locations in my mede8er it takes very long before I can see the NFS mapping.When I connect the Mede8er straight to the Synology NAS server (Cross Cable connection) NFS is working as it should be.So the TP-LINK WDR3600 cannot handle the NFS protocol?
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 0.4 v0005.0 Build 130217 Rel.62075n
ISP : TM Streamyx
I have internet speed : 8Mbps.
The status of Internet in the modem config as foloows:
UpstreamDownstream
Current Rate (Kbps)636 10240
Max Rate (Kbps) 900 23412
SNR Margin (dB) 12.8 23.5
Line Attenuation (dB) 8.1 1.1
Errors (Pkts) 0 0
from the above informations the upstream is 636 Kbps but when I did the speed test it show me that the upload not more than 300 Kbps.
I used another modem D-link modem and the upload is more than 550 kbps when I used speed test.
Actually the upload is very slow by using TP-link modem and when I used another modem the upload is double speed.
I just bought a DIR 615 (firmware 4.0) which I am using as an access point linked to a Netopia router. The Netopia has QoS enabled and needs to keep it, however I was hoping to use the DIR615 without QoS. I am using a ReadyNas Duo as storage for music, videos etc.Now, here are my issues which I think are all linked.
1) I have a very slow connection wireless, between 1'500 and 2'000kbits/sec download. This was not the case with my very old Linksys router
2) When I try to rip a CD from iTunes to the NAS, it brings up error messages of lost connection and impossibility to rip in the middle of the songs. I did not have that problem with the Linksys router neither.
3) I would like to change the QoS parameters to see how it affects this connection issue, as well as change other Wifi parameters, but they show up as greyed out and I can't change them. (I feel that the DIR 615 might inherit some parameters from the main router, since it is used as an Access Point).
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
I've connected a usb hard drive to my TD-W8968 and shared the root folder via storage sharing.When I try to copy files to the hard drive from my computer the transfer speed it about 700 Kbytes/s. When reading from the drive to the computer I get 2000 Kbytes/s.This is way below the 30000Kbytes/s that can be delivered to/from the drive when it's connected to the computer's usb. I've tried several usb drives and for all I get the same results.Is there a way to increase the read/write speeds for the usb connected devices?
Region : Malaysia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.13 Build 120605 Rel.38634n
The connection is slow when I connect my notebook to the TP-Link TL-WR1043ND wireless router. If I connect my notebook directly to to the ISP modem, the connection speed back to normal.
Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 121225
ISP : Online
Recently I replaced my Linksys WRT54G for a TP-Link WDR4300. But unfortunately this did not result in an increased speed.On both the 5GHz and 2.4GHz speed is limited to roughly 2.5-3 MByte/s, which is OK for watching movies etc. but I could reach those speeds with the 802.11g router as well!
I'm using the WDR4300 as access point, so I disabled DHCP server and NAT functionality, left the WAN port empty. And I set fixed IP in the subnet range of my modem/router. (horrible Speedtouch device). All works fine and stable, but too slow.
In the wireless settings I tried the 20 and 40MHz bandwith, disabled WMM, tried to lower the transmission power, tried to set a fixed channel. But all those changes do not have a significant influence on the transfer speed. (both on 2.4 and 5GHz) I'm the only 5GHz access point in my neighborhood, so interference cannot be a problem.
The clients indicate a link speed of 300mbps very close to the router, and this drops to indication of 54mbps further away, but effective link speed remains fairly constant (and stable!) (I find it strange that indicated link speed already drops at 3 meters with clear line of sight to the router)
I did the tests with fixed IPs on two laptops and no devices connected on the LAN ports, to rule out problems caused by the modem/router or other clients.The tests were done using a Lenovo x220 and Asus Zenbook, both with Intel dual band 802.11n wifi interfaces. The Lenovo reaches 22MByte/s via the Cisco access point at my work (with less signal as at home).
Region : Denmark
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Arrownet
I purchased a WDR4300 yesterday and have set it up. The internet is running smoothly although the transfer speed is rather slow. When transferring from my computer to my Seagate GoFlex Home i get about 6 - 8 mbps with Wireless N. The router is set to only use Wireless-N and my laptop has the latest drivers. I have also tried other computers in the house and the speed is the same. The GoFlex Home is connected to the router via a LAN cable. Prior to updating i used a Linksys WRT54GL and managed speeds of about 3 or 4 mbps over its G only connection. As for transfers between 2 computes the rate is about 1 - 3 mbps
As for distance the Wireless router is only about 1.5 meters from the laptop (across the room) with nothing in between them to cause interference. I have also checked what channels my neighbors use (using inSSIDer) and picked 13 as there is only 1 other person nearby on that channel and they are quite far away.
Region : UnitedKingdom
Model : TD-W8961ND
Hardware Version : Not Clear
Firmware Version : 3.0.0
ISP :
I was using dsl connected to pc with ethernet cable, on line streaming movies were fine, now with TP LINK ADSL2+MODEM ROUTER streaming has become very very slow using wireless, signal is excellent, web surfing is fine, do I need to change setting to improve streaming?
Region : Others
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : wr841nv8_en_3_13_27_up_boot(121101)
ISP :
I followed TP-Link's guide to set up a WDS connection between my two brand new WR841ND router. It theoreticaly "works", but the network is extremly slow. Copying a ~100 Mb sized file to another computer on the other side takes more than 10 minutes or more, I don't know exactly, because I shut down the process after 10 min. I pinged the "slave" router with 200 packets, and I realized that every third, fourth and fifth packet has more than 500 ms time. The minimum is 4 ms, the longest was 566 ms.
Router A (Master)
Connects to the internet/ADSL
DHCP enabled
[Code].....
I bought the two router from the same dealer, at the same time. Both have the same firmware. I checked all the chanels, and 5 is the only free one, but the situation is the same on every chanel.
What can couse this very slow transfer speed?
Region : UnitedStates
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 0.10 v0005.0 Build 120516 Rel.45877n
ISP : HiPointInc
Network Status.jpg
I've upgraded my line connection from 4mbps to 20mbps.I've also checked my status with HiPoint and on 192.168.1.1 which is shown on the attachment. No problems.
Max Downstream is 25612kbps but Current is only 4396kbps.Do I need to configure anything? Btw its directly connected to my PC?
1 newer build computer connected to D-link 655 via Cat6.1 laptop computer connected to same D-link 655 via Wireless N minicard. (Intel) (130Mbps connected) Router on a 10 foot shelf, always have full bar in wireless strength on 2nd computer.
Both computers can upload and download as expected from the internet. Transfers between the two computers though are slow. Both computers are loaded with Windows 7. Transferring files to or from the laptop transfers at 1.5MB/sec to 2 MB/sec.
