I am trying to setup a Wireless Home Network that extends to 2 different Parts of a Large House. Since the House is large 1 Router does not have the Signal strength to cover it all.I have a second wireless Router , a Spare Lan switch and 150ft Ethernet Cord to connect everything.
This all leads me to think that I missed some setting on Router 1.Though I cant figure out what I missed. As i said My Laptop is getting and IP and connected through the Cat 5 cable just fine. Should Router 2 not be able to simply pull an IP from the IP pool Router 1 and use Router 1 as its default Gateway?
My Belkin N150 wireless router monitor has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you us a solution is available.I can not figure out why my wireless router doesn't work sometimes.I need to be able to access this to get to the router settings. I don't know if my wireless is being highjacked or what.
I used Cisco connect to set up guest access with a secure password. Cisco Connect now indicates guess access is allowed and shows the password. However, when I actually try to connect to the guest network, it shows no security at all, and I can join the network without a password.
Model : TL-WDR3500 Hardware Version : Not Clear Firmware Version : ISP :
As we say, I followed all the directions but I am unable to setup the ftp server on this router. I even disabled Norton's firewall but am unable to access the server via WAN.
Region : UnitedStates Model : TL-WDR4300 Hardware Version : V1 Firmware Version : 3.13.23 ISP : Comcast
I have no problems connecting on a 5 GHz band or wired to the router. However any device connecting on 2.4 Ghz gets barely any bandwidth and drops after running for a short time. I have test numerous devices and have the same issue. What was odd is a device on 5GHz that worked fine had the same issue when connecting on 2.4 GHz which seems to say it is only that band. I have an old router that works fine on 2.4 GHz on channel 1 with all the security settings I used on the 4300.
Region : UnitedStates Model : TL-WDR4300 Hardware Version : V1 Firmware Version : latest ISP : Clear
Get GMT throws an error. I set known good public NTP servers, still get error. Also power cycling or rebooting the router seems to drop manual time settings, as well. I am using WDR4300 as a wireless access point, does that matter? Maybe I don't need time in access mode? It is connected to the Internet and is providing internet access to clients.
I have had the Netgear 3300 Dual Band for three years. Everytime I wanted to access using my laptop, I had to choose between 2.4G and 5G connection. For about a month now, the 5G does not show up. It doesn't show up as a network to select no matter what device I use. I have reset the router and updated the firmware. Both connection lights are blinking. I recently purchased and IPhone 4 and still I do not have the option of selecting 5G.
Region : Argentina Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP : Region : Netherlands Model : TL-WDR4300 Hardware Version : V1 Firmware Version : TL-WDR4300_V1_121225 ISP : Ziggo
Set up the WDR4300 with a USB drive connected (Platinum MyDrive CP 500 GB USB 3.0).Enabled the Media server, shared the entire drive, stuck an test .avi on there.My laptop has no trouble playing it from the attached storage, my Xbox sees the folders and files, recognizes them as playable formats but then does nothing once I hit play to get the file going.If I copy the exact same file to the shared folders on my laptop, navigate from the Xbox to that location it streams within the second.Also tried the same thing with a 16 Gb USB thumbdrive, same result.
Region : Argentina Model : TL-WDR4300 Hardware Version : V1 Firmware Version : Region : Others
I have Enable WDS Bridging and run Survey which detect the other SSID to be joined with the correct MAC address.I had filled the password of my second THOMSON v 585 V7 with the correct Auth Type both routers broadcast on channel 11.But my TP-Link 2543ND cannot made it work.I also disable DHCP and changed my LAN ip to 192.168.1.2 and can access it over my lan.
Region : Australia Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP :
I've been using inSSider on Windows and trying different settings on my 4300 to get wireless n @ 300MHz working with no luck. The maximum I seem to be able to get it to run is 144MHz.
Is this a fault with the router or the firmware? Since the router is advertised to run at 300Mhz, then by rights if it does not or cannot, then TP-Link owes everyone a refund, at least in Australia because this counts as false advertising.
I had a similar issue with my 1043ND as well. Has anyone got a 4300 working at 300 MHz?
Region : Canada Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP :
I recently bought the N750 wireless dual band router and I would like to setup a bridge with another router that I'm currently using.
I have followed the instructions in the documentation [URL]. But I've had 0 success in getting this to work.
How to get this feature to work?
Additional info:
I followed each step to the letter. In the last step when my router reboots I noticed that the System light doesn't flash. Which indicates that there is a system error (according to the user manual). But I'm unable to determine what the system error is because I can no longer log into my router's Administration page anymore.
in the instructions (link above) it says to disable DHCP, so I manually assign an IP address to my computer setting the gateway IP address to the IP address I manually assigned to my router. I can see that a connection to the router is established, but I'm unable connect to the internet and when I type in the IP address of my router I'm unable to get into the administration menu.
I checked the wireless connections on my source router and I don't see the IP address of the N750 router.
Region : Spain Model : TL-WDR3600 Hardware Version : V1 Firmware Version : 3.13.23 Build 120820 Rel.73549n ISP : Portal Wimax
I have enabled USB Print Server on the router and managed to print from my main PC (connected by cable to router).
However, I cannot get it to work on my laptop.
I connected my laptop running Windows 7 x64 by cable to router, ran the USB print server software (latest version downloaded from web site). The USB server software sees my printer (Canon Pixma iP4200). It appears in the list to auto-connect but there is an X against it and if I try and set it to auto connect, I get the error "the port of auto-connect can not be a LPR/Raw TCP/SMB port". Apart from the occurrence of the printer I had installed before (so, yes the printer driver is installed), the USB-server printer does not appear in my system printer list.
Region : UnitedStates Model : TL-WDR4300 Hardware Version : V1 Firmware Version : 3.13.23 Build 120810 Rel.44064n ISP : COX
Trying to set up my Samsung ML-1430 printer using a Mac OS 10.6.8. Downloaded and installed the TP-Link_UDS_Printer_Controller. The printer controller found the printer and and it is now connected as the "Auto-Connected Printer" but it does not show anywhere to be selected so I can print to it. Tech support suggested uninstalling and reinstalling the software which I did. Still no option to print to it.
Region : Hongkong Model : TL-WDR4300 Hardware Version : V1 Firmware Version : TL-WDR4300_V1_121225
Even I have upgraded to the newest firmware for WDR-4300, it still not allowed me to connect to a windows PPTP VPN. It worked when I changed to use my old router. On the other hand, when I turned the hardware NAT, I found that the Cisco VPN connection would be dropped after I used for a few minutes. Similarly, it worked when I changed to use my previous old router.
I'm a bit new at this and I wanted to know if this is possible with the RV042 or if there's a better product to use. Our server is at located at location A and locations B and C telnet to the server via a VPN. We're looking at getting another ISP at each location as a backup and abandon older modem backups.
Would I setup a VPN tunnel between (A and B) and (A and C) for each ISP? Also I had a question on local IP addresses and if this would work
location A, ISP 1 -> location B, ISP1 local IP 192.168.1.1 remote IP 192.168.2.1 Public IP aa.aa.aa.aa Public IP bb.bb.bb.bb [ code]....
Belkin Setup / Router monitor application has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available.
When I try gaming on my computer and someone else is gaming on the ps3 or is on another laptop I run into lots of lag. I've upgraded my internet service for more bandwidth, I forget exactly how much it is. Anyway, I want to connect my normal devices on the 2.4 and my two gaming computers and ps3 on the 5.0. How do I do this and how do I know if my computers and ps3 are even compatible with the 5.0?
The Network adapter for one of the computers is atheros ar8152 NDIS 6.2
I would like to configure port forwarding in such way that connections to both WAN interface on identical ports will be redirected to a single host in a private network. When I issue command: ip nat inside source static tcp 10.10.10.X 8080 interface g0/1 8080 everything is fine, until I add the second command: ip nat inside source static tcp 10.10.10.X 8080 interface g0/2 8080
After that, the first statement is just replaced by the second one, not added to configuration.
I got Windows 7 Enterprise-32 bit which cannot run some old programs,games,etc.So i decided to install Windows XP professional, but there's a huge problem: The internet does not work when i change to XP, but when i change back to win 7 it works again. Should i call my internet provider?Unplugging,creating,disabling the internet does not work,also it's not the problem with firewall.
Region : UnitedStates Model : TL-WDR3600 Hardware Version : V1 Firmware Version : ISP : Centurylink
I'm using a WDR3600 router, and I'm having difficulty with getting internet access on the 5 GHz band. Right now the router is broadcasting in both 2.4 and 5 GHz as two separate APs. The 2.4 GHz band works perfectly fine, but when I connect to the 5 GHz band my device is not assigned an IP address and cannot connect to the internet (or even the router configuration page). Unfortunately, I don't have another device capable of accessing the 5 GHz band, so I can't check to see if the computer is at fault, but both the computer and the router have worked together with no problems before, and this computer has done fine in accessing other 5 GHz bands.
Below is the config has done on my 881g but the dual NAT failover is not working.I have a easy vpn over NAT (easy vpn firewall: 10.10.10.2 behind the router).
1. After completed the config, I shut down the FastEthernet4, cleared the nat translations, found that nat translations are happening on to Cellular0 with error ( Incomplete ESP translations: 0 esp_conn=0x85A91FF0, hanging off nat entry 0x85A7D1D0)But still the easy vpn is not up as I am not able to ping the remote devices.
2. If I reboot the router then the nat translations are happening with no above error and easy vpn is up and I am able to ping the remote servers. Below is the config, what needs to be done to achieve the NAT failover and easy VPN up.
interface FastEthernet4 bandwidth 2048 ip address 206.206.206.2 255.255.255.240 ip flow ingress ip nat outside ip virtual-reassembly duplex auto speed auto interface Cellular0 ip address negotiated ip nat outside ip virtual-reassembly encapsulation ppp dialer in-band dialer string gsm dialer-group 1 async mode interactive ppp chap hostname. [code]
I am trying to setup a Dynalink Wireless 4 port modem and Network Connection is showing Local Area Connection Network Cable Unplugged,Firewalled, Broadcom Netlink (TM) Ethernet even though the LED light on the cable is flashing, indicating the cable is probably working. I am operating Windows XP Version 2002.
I have my RV042 set up in Dual WAN mode and both WANs are working properly. I would like to configure WAN1 to handle all traffic, unless it fails and then have everything to go to WAN2. Pretty much what Smart Link Backup does, however with that enabled only 1 of the WANs is live at any given time. I'd like both WANs to always be live as I'm going to see the second one as a back-door into the network. Is this possible to do with routing? I tried setting a routing rule to have everything to go WAN1, but when WAN1 goes down, nothing is rounted via WAN2.
The internet at my parents house has recently gone on the fritz..the wireless router is a N600 Wireless Dual Band Router WNDR3400..The computers of the house are able to connect to it..But it does not allow internet connections..The 3 computers are an HP Laptop running windows 7.a Dell Dimension E521 Running windows 7 & and an older HP Walmart special running XP.They can connect to outside systems and through a wired connection to the Modem from Cable vision. They replaced the wireless router and the problem continues.Internet is capable by plugging directly into the Cable vision router,unfortunately do not have the cables to try through the Netgear router to test that out..
I just bought a linksys wireless n dual band router e2500 and i want to make my old wrt54g router as an access point. how do i do this and where to start?
I am trying to get a NAC demo running and am having some issues with a Layer 2 OOB, Virtual GW configuration. Currently I have 3560G switches and would like to assign ports to a vlan based on user roles.
My Auth VLAN is 110 and maps to VLAN 11 Guest VLAN is 11 (172.16.1.0/24) Employee VLAN is 1 NAS Mgmt VLAN is 20 - CAS is 10.10.20.5 (this ip is setup on both eth0 and eth1 per documentation for L2 OOB Virtual GW) NAM Mgmt VLAN is 30 - CAM is 10.10.30.5 Untrusted (Eth1) switchport is setup as a trunk allowing only vlan 110 and has a native vlan 999 to blackhole traffic. Trusted (Eth0) switchport is setup as a trunk allowing vlan 1, 11, 20 and has a native vlan 998 to blackhole traffic.
I also setup a Managed Subnet on the CAS with IP 172.16.1.254 and VLAN 110.Switchport controlled by NAC is access vlan 110. When a machine connects an snmp trap is sent to CAM and is forced into vlan 110. If I try to put the port in another vlan CAM puts it back to 110 immediately. This all seems to be working well.The machine connected to the port gets a DHCP address from VLAN 11. When I initiate traffic from this machine, everything is blocked. If I open a web browser I do not get an authentication page. I also installed CCA 4.1.10 on the machine but it does not find a discovery host and the Login option is grayed out. The only way to get this machine to send traffic is to add a filter for it and force it to the ALLOW option. I did setup a default web login page but I seem to be missing something to get authentication to work. I am running version 4.1.8 with a demo license. The host running CCA is Windows Vista.
I would like to make a design with 4 Nexus 5596UP. 2 of them equipped with Layer 3 Expansion Module so they can serve as core layer and the other 2 Nexus used as Layer 2 for aggregation server layer.The 2 Nexus in the core layer will run HSRP and will peer with ISP via BGP for Internet connection The 2 Nexus in the aggregation layer will be configured as layer 2 device and have FEX and switches connected to them.What I am ensure of is how the vpc and port-channel configuration should look like between the 4 nexus. What I was thinking is to run vpc between the 2 Nexus in the aggregation layer and between the 2 Nexus in the core layer. Than I was thinking of connecting each Nexus in the aggragtion layer to both Nexus in the core layer using port-channel and vice-versa.
how to change our wireless setup. Currently, we have 2 Cisco AiroNet 1130 WAP's in the office that go directly into the 2 POE ports on our Cisco ASA 5500. These WAP's have 1 SSID and are using WEP for security. After demonstrating the flaws of WEP to my boss, he has agreed that we should use something more secure and I've suggested WPA. We want visitors to our office to be able to hop on our wireless but on a separate guest SSID with WEP.
I'd like the internal SSID to route to the ASA and take the default route to the internet (it will be our new fiber connection once it's installed in a couple weeks). The default route is whichever connection is working since our ASA 5500 will fail over when it detects an outage.
I'd like the guest SSID to route to the ASA and then go over our existing cable connection. This connection will be our backup once the fiber connection is installed. Since we won't be using it very often, but will be paying for it, I advised that we send all guest wireless traffic over this connection since 50/5 is plenty for guests.
The current SSID (which will be the internal SSID) has no VLAN. We do currently have a few VLANS on our network, one for voice (.42) and one for data (.100) and the default (.0). What device to I create the VLAN on (Cisco 5500?) and how to I setup the WAP? I need very basic instructions to start and I'm also trying to do this without causing downtime if possible.
I've attached a diagram of what it should look like. Red indicates our internal network and Blue indicates the guest network. I can send screenshots as well.
