Easiest Way To Root My Toshiba Thrive?
Mar 22, 2012how can I root my Toshiba thrive 31.5.003 without messing anything up cuz I'm tablet eleterate an its brand new
View 1 Replies
ADVERTISEMENT
Linksys Wireless Router :: Cannot Get Toshiba Thrive To Recognize Wrt-1209
Dec 15, 2011I cannot get my Toshiba Thrive to recognize my router (wrt-1209) or the other way around. I am able to get on a neighbors non-secure network immediately. No problem with the other wi-fi connected computers on my network.
View 1 Replies View RelatedCisco Wireless :: 1400 - Equipment Cannot Bridge To Other Root Or Not-root Mode
May 3, 2013We have a problem with a Cisco 1400 Bridge. This equipment can not bridge to the other root or not root mode. I can see a message "Interface Dot11Radio0 Radio transmit power out of range" and the MAC Address of Dot11Radio0 appears with 0000.0000.0000.I set the local power to 18 but the MAC Address is still in 0000.0000.0000.
View 1 Replies View RelatedCisco Wireless :: 1300 Bridges Root And Non Root Can Associate / Ping Each Other
Oct 18, 2011i got the problem with 1300 bridges,root bridge with omni antenna and non root with sector antenna , it can associate and can pin each other , but whenever i try to browse several web pages its get timed out and radio was down.
View 5 Replies View RelatedCisco :: Working Configuration Between Two BR1310s In Root And Non-Root Mode
Jul 18, 2011Any working configuration between two BR1310's in Root/Non-root mode? The documentation is vary vague and i can't find anything more secure than WEP. Is it possible to use WPA with radius authentication?
View 1 Replies View RelatedCisco Wireless :: Associate Non-root Bridge Model 1310 To Root Bridge Model 1400?
Apr 24, 2012Can I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies View RelatedEasiest Way To Image About 15 Computers Over A Network Over Night?
Oct 30, 2012As the title says, I would like to know what are some ways in which a group of computers on a network can be imaged at the same time over night. The reason this must be done is because in the training room at where I work, each different training session configures the computers differently, so it would be nice to have them all start off from the same point, rather than a new instructor having to learn all of what the previous instructors had done to the computers.I know some ways in how to image multiple computers. A little background on the environment:
About 15 computers connected a cross a network
Must be repeatable, and remain available (no dismantling)
Image will be Win7 32 bit, with applications already on it
Must be able to run, and complete over night
The image must be pushed out from one computer to all of the others
The OS of the computer doing the pushing can either be Win7 or XP
Networking :: Easiest Way To Put RJ45 Jacks Onto Cat5
May 13, 2013Is there an easier way to connect an RJ45 connector to a Cat5 cable, rather than the traditional method of lining up the wires by hand, inserting them in the right order into the jack, and then crimping it? It just seems like it would be very tedious if you had to do this A LOT, and I've had a good bit of practice. I saw that they make "EZ RJ45" jacks.. but do they make anything else that can make it easier? I'm asking out of curiosity, and not necessity. I have no problem wiring them, but it's just something that I hate to do (I think a lot of people would agree that it's not the most fun thing to do in the world of networking).
View 13 Replies View RelatedLinksys Wireless Router :: E2500 - Easiest Way To Extend Connection?
Jul 13, 2011I just purchased a E2500 wireless router to upgrade from the previous G- router which I was using. I'm not very experienced in tech issues and would like to know, what would be the easiest way to extend my wireless signal through out the house. The E2500 which I just purchased does not cover all the areas in my household.
View 1 Replies View RelatedCisco :: 5508 / Easiest Method To Block Employees From Guest Network?
Jun 3, 2013We have WCS and several WLCs (WISMv1, 5508, 4402) all running the 7.0.240.0 code. The "Guest" SSID is "garden-walled" from the corp LANs. We used to have web-auth page that required ID / PW. This became unreasonable as IT Dept was getting requests at all hours for immediate access from guest / resident family memebrs. So we changed the web-auth to remove the the ID / PW and just display corp policy and have to hit a "continue" button to gain access to Guest SSID. Healthcare staff on the floor are not tech-savvy enough to want to use or perform Hotel Ambassador functions.The issue now is that we have employees with smartphones, tablets and even personal laptops conecting the Guest SSID. Sr. Mgt wants to find a way to stop the abuse.I do not believe there is any perfect solution to prevent employees from gaining access, but have been asked to find a manageable method to deter most employees from connecting to the Guest network. Looked at seing up MAC filtering in WCS, it seems that you have to enter MACs that you *allow* on to the network - by default, other MACs are blocked. I would rather have the template block the MACs listed in the csv file and allow access as the default.. We have several SSIDs. Our corporate SSID uses 802.1x and we use Microsoft Server 2012 Network Policy Server (RADIUS) to pass user ID / PW to our AD for authentication. We do not have Cisco ACS. I am not sure if integrating RADIUS is the answer here either. I have had some webex sessions on ISE, NCS, and Prime infrastructure. We are only interested at the moment to monitor / control access to Guest. I have been told that ISE will have "sponsorship" functionality added in soon -- where user fills out info and ID / PW is sent via text or email to a cell phone or other device.
View 2 Replies View RelatedAdding A Second DC To The Forest Root Domain?
Feb 27, 2013I have installed Windows Server 2008R2 on a virtual machine and have setup AD and a domain name called nuggetlab.com and is the first DC. I've created another VM and again installed Windows Server2008r2 and want to add a second DC to the forest root domain. When i run dcpromo and at the option 'Choose deployment conifiguration' wizard i select Existig forest >Add a domain controller to an existing domain > Next, the next screen appears and i type in the domain as nuggetlab.com but when i enter the credentials under 'Alternatate credentials' and enter the admin username and password, i receive an error saying that it cannot be contacted. When i press the details button i can see the description[CODE]
View 5 Replies View RelatedAAA/Identity/Nac :: ACS 5.1 Join To Root / Subdomain
May 5, 2011is it possible to join the ACS 5.1 to a rootdomain (AD) with a subdomain and to authenticate against the subdomain? Or do I need different ACS' for the root and the subdomain?
View 2 Replies View RelatedCisco :: CCNP - STP Root Port Election Example?
Jun 23, 2012I am currently working on an example for a CCNP Spanning Tree Protocol example.I have some lectures on video and getting confused with an example they have provided. It has me baffled as I have compared it against numerous other websites, trawled forums and tried to get other examples to compare it against.Anyway, I have posted screenshots of the topology. They are as follows:
1) topology showing links so can assign costs (100mbps = STP cost 19, 1000mbps = STP cost 4)
2) topology show priority and MAC addresses (priority left at default so root bridge elected by lowest MAC address)
3) topology showing elected root ports **which I do not agree with for switches E & F**
4) topology showing subsequent blocked ports **which I do not agree with for switches D & F, even if I accepted the previous given root port election*** I understand for same cost paths to root bridge that lowest bridge ID wins. So here are my queries:
1) switch E has 2 equal cost paths to root bridge (A):
-via: E > D > A (4 + 19)
-via: E > C > A (4 + 19)
so I think pick the next hop switch with lower bridge ID. Switch C right? In this example it says pick port going to switch D. I am confused! Why pick port going toward switch D?
2) switch F has 2 equal cost paths to root bridge (A):
-via: F > C > A (4 + 19)
-via: F > D > A (4 + 19)
so I think pick the next hop switch with lower bridge ID. Switch C right? In this example it says pick port going to switch D. I am confused! Why pick port going toward switch? tell if the example in the diagram (topology 3) is wrong? If it is correct explain why?Now on to issue number 2...If I accept the root port election given in the topology, I go through the process of assigning designated ports and blocked ports.I understand for each link there is at least 1 designated port. If it is a redundant link, one side will be designated, one side blocked. The designated port will be on the side of the lowest bridge ID (priority + MAC address). So here are my queries:
1) there is a redundant link between switch C and switch F
-one side must be designated
-one side must be blocked
-pick the side with lowest bridge ID (priority + MAC address) for designated port
-switch C has same priority as switch F, so based off MAC address, switch C wins i.e. designated port on switch C side, blocked port switch F side.
-In this example it says port from switch C is blocked and port from switch F designated. I am confused! Why pick port going from switch F as designated?
2) there is a redundant link between switch D and switch C
-one side must be designated
-one side must be blocked
-pick the side with lowest bridge ID (priority + MAC address) for designated port
-switch C has same priority as switch D, so based off MAC address, switch C wins i.e. designated port on switch C side, blocked port switch D side.
-In this example it says port from switch C is blocked and port from switch D designated. I am confused! Why pick port going from switch D as designated?
Cisco Wireless :: ACS 5.2 / Setting Up APs In Root Repeater?
Sep 16, 2012I am trying to configure repeater mode on an AP, but the authentication is not working.It seems the authentication is seen as EAP-TLS on the ACS 5.2, but im trying to do LEAP.
Relevant config root AP:
!
dot11 ssid Auto3
authentication open eap eap_methods
authentication network-eap eap_methods1
guest-mode
infrastructure-ssid
[code].....
Cisco :: 2960 / SSH Login Local In Root?
Feb 10, 2013I have a very problematic situation here.I have configure on a Cisco 2960 the vty line in a wrong manner and now I am stock.To configure those vty to enable ssh I have typed :
line vty 0 4
login local
password xxxx
line vty 5 15
login local
password xxxx
exit
Problem, I work remotely (I was on telnet while doing this). I have no username configure as I thought that root user would work.Now when I issue an ssh to my switch, I always failed authentication.how I could recover access to my switch without being physically there ? I have write the config in memory, otherwise it would have been too easy.
Cisco :: C1921 Router - How To Tell AP To Get New Root CA Certification
Oct 20, 2011I'm currently trying to set up a new infrasturcture with PEAP.
So, i've got redundant CA routers (c1921), an ACS server and 1262 AP's. Everything is working fine and as i want it to.Certificates are autoenrolled and so on, but if the CA root certificate expires, how to tell the AP to get the new root CA cert.
The root-certs are made by auto-rollover, and rolled on the CA router, but I got no change to get this root-cert on the AP.Is there a way to get them in an automated way, like rollover or enrollment?
Cisco :: STP Root Port Role Election Criteria
Oct 16, 2012I've not found much detail regarding election of a root port other than "The root port is the switch port with the lowest path cost to the root bridge" they also expand on this a bit more for the case below, (italics)." When there are two switch ports that have the same path cost to the root bridge and both are the lowest path costs on the switch, the switch needs to determine which switch port is the root port. The switch uses the customizable port priority value, or the lowest port ID if both port priority values are the same".They explain that on S2, F0/1 is root port because it's lower than F0/2 but don't go beyond this.My understanding is that the following order is true with regards to priority of criteria (in this case), am I right?:
1. Lowest cumulative path cost back to the root bridge
2. In case of tie, the device with lowest Bridge ID
3. In case of tie, the port with the lowest received priority #
4. In case of tie, the port with the lowest local ID #
So, shouldn't this demonstration factor in the BIDs of S3 and S4 before the port priority and IDs of S2 ? For instance, if the BID of S3 was lower than that of S4, wouldn't F0/2 on S2 become the root port? I'm hoping I'm correct in this? Also I've not actually seen these four bullets in any of my official material for STP which I thought was a bit odd. I wondering if anyone else who has seen this before, considered the bridge ID aspect.
Cisco :: Spanning Tree Root Mac Address References
Apr 19, 2012I am trying to confirm which of my cisco switch is the spanning-tree root. I know which I prefer to hold the spanning-tree and I ran the command spanning-tree vlan 1 root on this switch,I would now like to check that this command has worked and so I ran the command 'show spanning-tree root active' and received the detail below.To make sense of this and determine which port the mac address references (From this I take it that 00b0.d0f5.cf31 is the root, how can I determine which port this is).
View 15 Replies View RelatedTP-Link ADSL2+ Wireless :: TD-W8980 Test DNS Root
Feb 18, 2013Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
Another query regarding diagnostic test and Test DNS Root. It always fails why?
Cisco Firewall :: ASA5550 Doesn't Seem To Address Root
Feb 22, 2012I have been getting overrun errors on 3 different ASA 5550 HA pairs with traffic rates less than 100Mbps total. I was told by one TAC guy to split the traffic between the two slots so that traffic comes in one and exits the other to maximize throughput because the 5550 was designed to work that way. Another TAC guy told me to enable ethernet flow control to alleviate the overrun errors because the traffic was bursty, but this doesn't seem to address the root cause of the problem to either. TCP traffic is bursty by nature and has it own flow control mechanism. I can't seem to find any detailed info on why traffic needs to be split for 100Mbps when the marketting throughput number is 1.2G. Is this a design flaw or limitation? Is there a way to alleviate overrun errors?
View 25 Replies View RelatedCisco Wireless :: 3502P Running As Mesh Root AP?
Apr 14, 2013if the Cisco 3502p AP can run as a root mesh access point ?
View 4 Replies View RelatedCisco Application :: Root Password For ANM 4.2 Virtual Appliance
Sep 18, 2011The upgrade process for ANM virtual appliance 4.2 involves doing a backup and restore as root user. I have looked through the documentation and have even reinstalled the virtual appliance to see if the install script gives away the root password for the OS but without luck.
How to set/find the root password?
Cisco LAN :: 6509 / 2950 - Root Port / Cost
Dec 31, 2011On a production 6509, I am seeing this:
RTR-01#sh spanning-tree int gi2/3 rootVLAN0001 0VLAN0010 0VLAN0011 0VLAN0012 0VLAN0013 0VLAN0014 0VLAN0015 [ code]....
Now I thought the command "sh spanning-tree int gi2/3 root" showed cost to the root bridge. So with everything being zero, its implied this the root, which it is but not for vlan 111 and actually all 1XX Vlans have a different root. Why does vlan111 show its root as out int gi 2/3 but the root cost shows zero?
Issue is we have a issue where a 2950 is acting as root bridge for our wireless vlans, wrong....it should be the 6509, but before I change it over, was wondering about the root port/cost question.
D-Link DIR-655 :: Installing Files In The Root Directory Of Mac Hard Drive?
Apr 4, 2011This is troubling and I don't know why it is happening. For some odd reason files seemingly related to my DIR-655 are being put in the root directory of my hard drive on my Power Mac G5 running Leopard 10.5.8. Two preference files and a folder named ''D-Link'' and another folder named ''Shareport.''Why is this happening? I have given D-Link/DIR-655 no access to my hard drive.Furthermore, why this is only happening on that machine while my MacBook Pro running Snow Leopard 10.6.7 is not being ''invaded.''
View 12 Replies View RelatedCisco Switching/Routing :: 4X SGE2010 / Two Root Bridges In Network
Oct 16, 2012I have a setup where - I have a cisco stack (4X SGE2010 Switches) trunking over to a 3COM switch. Both switches believe to be the "ROOT" of the network. Note The 3COM is running RSTP as opposed to the Cisco Stack which is running normal STP. To my understanding of STP - Essentially STP is not functioning! Both switches believe to be the "ROOT" so they don't shut ports down. (We are currently having major issues with ports going up and down for seconds at a time on both switches)
View 3 Replies View RelatedCisco Switching/Routing :: 3750 STP Vlan 21 And 22 Root Bridge On 2 Switches
Feb 16, 2013I config vlans 21-23 on 3750 A and B switches.I config B switch to be Root Bridge for all vlansspanning-tree vlan 1,21-23, priority 4096 sh span tree on B switch 3750B# sh spanning-tree.
View 18 Replies View RelatedCisco Wireless :: Aironet 1262N - Access Point Behind Non-Root Bridge?
Apr 9, 2012I want to connect two buildings. Let's call them Building A (main) and Building B.
„A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
My Questions:
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?
2. How Do I tell AP03 that it should use AP02 as a gateway to building A?
Cisco Switching/Routing :: 8192 / STP Root Bridge Is Pointing At FWSM?
Feb 11, 2013I have two 6509s both with single FWSMs running in transparent mode with bridged Inside and Outside VLANs.I have my Core A set to STP priority of 8192 and Core B set to 16,384 to make Core A the root for all VLANs.Problem I have is when I look at spanning-tree on Core A for Inside VLAN 324 it states to get to the Root go via PO100 (Cost of 9) and that the Root also has a Priority of 8192, but as the designated Root has a lower MAC address it's pointing to the etherchannel. PO100 is L2 Etherchannel between the Cores.Moving accross PO100 to Core B and running the show spanning-tree command I can see that to get to the Root Bridge I need to go via PO272. PO272 is the internal Etherchannel to get to the FWSM on the Core B Switch. This shows a cost of 6 to get to the Root and a mac address of the Root Bridge which resides on Core A (Outside VLAN 124)To give some perspectibe,theoutside VLAN of the pair has it's STP ROOT on the Core A switch as intended?
View 1 Replies View RelatedCisco Switching/Routing :: 2950 Root Bridge ID / Avoid Loop
Jan 18, 2012I have an Extremely Old switch that I need to connect to my network. Because it is so old I don't want it to become the Root Switch.
what is the command to change the priority. (Honestly I don't remember if it has to be a lower number 1 or a higher number ). Always get that mixed up. I've read about root guard, but I would like to prevent it manually. (It is a small network after all)It is a Cisco 2950.
Cisco Wireless :: 1524SB - Have Root AP Whose Status Light Showing Solid Red
Jun 30, 2011We have a root AP whose status light is showing solid red. We power cycled it and it still shows solid red. According to the Cisco documentation, this indicates a firmware failure. Unfortunately, we did not get Smartnet with this access points and instead opted for the limited lifetime warranty.
My question is: is there any way to fix the firmware via console? Whether it be through xmodem or what not. I ran debugs on the controller and can confirm that the AP is not communcating with the controller.
It is also weird that the mesh APs that were previously connected to this root AP show a solid red on their status lights and green for their RF LEDs. Shouldn't the status LED be flashing green-amber-red?
Cisco Switching/Routing :: 3550 - Two MST Instances Enabling Root Guard
Jan 12, 2012I have 2 3550 12G switches that I use as core fiber switches. Switch 1 is the primary for 1/2 the V LANs and Switch 2 is the primary for the others using MST with 2 instances (I am not including the default 0 instance). I am using HSRP to provide redundancy. So far so good.
Recently a tenant in my building would like to use their own switch for data but still needs access to a V LAN on mine for voice. Again not a problem as I can configure a trunk port and give them what they need. My concern is that if they try to configure STP on their switch can they take down mine. Are there some preventions that I can put into place, such as root guard, that work with MST? What happens if they too set up MST can they kill mine?
Switch 1 is the root for 1/2 the v lans and Switch 2 is the backup root. The scenario is flipped for the other 1/2.
Cisco Wireless :: 1260 Root AP De-authenticating WGB Clients After 6 Minutes Of Inactivity
May 27, 2013i have 2 1260 Access points one is in root mode , one is wgb mode. Authentication is EAPFAST. There are 5 devices connected via WGB bridge to the rest of the network.
- If clients are sending some data , then WGB AP announces this client mac via IAPP to root AP and rest of the network sees them correctly
- If clients are "passive" , then after WBG AP announces them to root AP , they timeout after 6 minutes on root AP and obviously they are not pingable from the rest of the network. The only way to restore connectivity is to ping that device from WGB AP, then WGB AP announces via IAPP to root AP , then and only then they become visible from the rest of the network.
My question is related to this 6 minute timeout on root AP . Is it normal behaviour ?
Cisco Wireless :: Configuring Root Access Point And Repeater In 1252-AG-A-K9?
Dec 19, 2011how to configure Cisco 1252-AG-A-K9 Access Point Root and Repeater?
View 9 Replies View Related