My desktop is telling me I need to install wireless internet hardware. Is that something I buy and install? I am trying to connect to the internet through time warner cable wireless.
View 1 RepliesMy wireless network connection appears to be working; I can access the Internet from my laptop, iPad, iPhone, but not from the Dell PC that is the 'host' computer. Local Area Connection 2 Status window shows it as working, when I try to repair it, I get hung up with an error msg:
>>"Windows could not finish repairing the problem because the following action cannot be completed:
Clearing NetBT
For assistance, contact the person who manages your network." <<
System info: Dell PC (don't know model) running Windows XP Home Edition v. 2002 Service Pack 3;
Intel Core 2 Duo CPU E 7500 @ 2.93GHz, 1.96 GB of RAM
OS: Windows 7 Home Premium -- Service Pack 1, 64-bit
Browser: IE 9
Computer: Dell Studio 1745
I am receiving an error message window titled "Wireless Configuration" with the following message:
"OLE initialization failed. Make sure that the OLE libraries are the correct version."
I cannot find anything about updating OLE libraries in Windows 7. I have not installed any new software, and my computer is barely 2 years old. I do not find it a coinicidence that my free Dell tech support expired last month, and now I'm having issues with the Dell wireless card.
i keep getting an error message when i scan. error message: cannot communicate with scanner for these reasons
-scanner is turned off
-scanner is disconnected (it is disconnected from LAN, if using on LAN)BUT MY MACHINE IS ON
Sylvania Smartbook synet7wic-bk cannot get online. It shows my wifi is on, but I do not have a tab for wifi information, to put my info in it.
View 2 Replies View RelatedI purchased a WRT110 wireless router several weeks ago. Used it with my WPC55AG with no problems at all. I liked the wireless-N, so I decided to upgrade to a wireless-N notebook card and purchased a WPC100. I can always connect to the router with 100% signal strength. However, when trying to access the Internet, sometimes I can connect to websites, but I regularly get an error message that Internet Explorer cannot connect to the internet, even though the signal strength is still 100%.
Tried going back to my WPC55AG and do not get any connection error messages. Tried connecting to my router with my PSP and do not get any connection error messages. Connected to another wireless router that didn't have WPA or WEP using my WPC100 and didn't get any connection error messages..
My wireless internet has been working perfectly well on my XPS 17 (L701X) until last weeky. I was on the internet and then my wireless turned off suddenly. the error message says "turn wireless capability on". BUt on the wardware, the witch is on, but when I check windown mobility center, it shows "wireless off" . Ran network diagnostics, but same error massage "turn wireless capability on". For now, when it happens, I need to restart my computer and it back to nomal. This happens at least 3-4 times a day.
View 1 Replies View Relatedcomputer was working fine a few days ago, all of the sudden not able to get online anymore at all,recieve error message 651 with dsl connection, and when trying to connect to wireless get an error message saying invalid ip adress configuration,
ipconfig/all reveals:
C:Usersygydfre>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : bygydfre-PC[code]......
I am trying to set up a E2500 router to a Arris/Comcast modem. I connected the blue cable to the router then to the modem and followed the Cisco instructions on the disk. I was 90% done when I received a error message 82BD0118 - Description - adapter connection time out period expired with no IP address.
View 2 Replies View RelatedI have an HP C5280 printer running wirelessly via a TP Link wireless print server and D Link Di 624 wireless router. I can print successfully from either my desktop (which is connected direct to the D Link router) or either of my laptops (wireless). However, when I select the double-sided print option I get a print error message after re-inserting the odd number pages to print the other side of the paper and then click 'continue'.Could I resolve this by connecting the printer both direct to the desktop using USB AND leaving it connected via the wireless TP Link print server? This would enable me to print double-sided from my desktop (as I did before when the printer was only connected via the USB desktop port).
View 1 Replies View RelatedMy roommate has just gotten a second hand laptop and he's trying to connect it to the Wireless network so that he can browse the internet from his room.However, although all the settings are correct, attempting to connect to the network loops.It comes up showing the Wireless Networks available, I select the network and click connect, it then asks for the encryption key. I enter the key and hit connect again, it comes up with the 'Connecting' pop-up and then loops back to the Available Networks screen again.There are no error messages, it just goes back to the starting screen and it hasnt connected.The Laptop in question is a Lenovo T60 with a Intel PRO/Wireless 3945ABG card.The router is a TP-Link TD-W8960N.
View 5 Replies View RelatedI recently bought the E2500 Router and I am using the EA2500 Adapter with it . I have this set-up on 2 Desktop PC's . 1 Pc is working just fine with this set-up . The other keeps giving me an Error message of "Invalid Key Manual" . What does this mean ? The adapter is working because it does find the Router as a usable connection . It just isn't able to connect to it and keeps giving me the same Error message .
View 8 Replies View RelatedMy WRT54G router is already feeding 2 wireless PC's with no problem. Haven't been as successful getting my new Samsung Series 7 TV wireless connection working. The TV screen prompts for a 'security key', but once entered, tells me the connection is unsuccessful. The TV does not provide any specific error message - just tells me to re-enter the security key and/or re-start the router (which I have done many times with no success). I am entering the 'Encryption key' from the WRT54G router when prompted by the Samsung TV for the 'security key'.
View 2 Replies View RelatedUpon checking the logs, I'm seeing a lot of these messages:
*emWeb: Oct 25 14:11:01.345: #LOG-3-Q_IND: spam_lrad.c:10136 Validation of STAT_PAYLOAD failed - AP 00:3a:98:09:4e:d0
Always the same MAC address, which I assume is a Cisco AP trying to join. The output interpreter/message decoder isn't much useful. 5508 Controller running ver 7.3.101.0.
Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP : Virgin Media Limited
when I forward ports I get the following error message:
Things to note:I have the web GUI running on 8080, because I run a file-server on port 80.
I am using a Virgin media branded router in 'modem mode', this would not cause issues.
I did not do anything to change anything, I went to add an additional port to forward and it didn't work.
I am on a Dynamic IP
After it stopped forwarding, I upgraded firmware to: 3.13.26 Build 130129 Rel.59449n.
Is there I can customize the error page which is shown when someone visits a blocked site
View 3 Replies View RelatedWhen i try to connect kf to wifi router, I keep getting password error message when I type my network pw. I have no problem connecting to other wifi connections
View 6 Replies View RelatedI have a Netgear WNR612 wireless router, which worked fine for a few weeks. Then something happened and I can't keep the connection anymore. It happened right after I used iTunes to update my iPhone, perhaps a coincidence, but I'm mentioning that just in case. Internet still works fine with ethernet cable straight from the computer, only the wireless connection doesn't work. This happened about a month ago and I haven't been at home much to fix the problem. I have turned off and unplugged everything for several days at a time while gone. I get a Network Error message saying, Windows has detected an IP address conflict. I have tried restoring the router back to factory settings and reinstalling the wireless card. I have tried changing the IP address settings both in the Network and Sharing Center and the router admin page. What I think I should do is change the IP address in Command Prompt, but when I type "ipconfig /release", it says "No operation can be performed on Wireless Network Connection 2 while it has its media disconnected" and the same for Local Area Connection. I don't understand what this means, because there is a wireless key in my keyboard and there is a white light (not orange) like there should be. Also in the Network and Sharing Center, I can see that the connections are enabled.
View 14 Replies View Relatedi am attaching the image which i recieved last night when i was assigning the IP but i got the error message which does not resembel to IP conflict error messsage
View 1 Replies View RelatedNotified of new firmware for my router. Tried to install. Downloaded fine but will not install. Keeps saying error but not what kind, how to fix, not anything.
View 1 Replies View RelatedSometimes, either browsing from my computer, iPad or iPhone, I sometimes get a "can't connect to server" error, and it's not just a few forums here and there, it is a lot of them. But if I give them 5 or 10 minutes they will come. Imkmow that this isn't a normal up issue with sites servers actually being down. I thought it was a Google chrome issue, but it's been happening on safari. It hasn't started till we switched our Internet plan to 3mbps and a new router.
View 19 Replies View RelatedI keep dropping off my internet connection and getting this error.
View 11 Replies View RelatedAfter making some physical changes to my home network (which had been running for sometime without incident) my desktop machine stopped (home built MSI X58 Platinum MB) talking to the network. I get "media not connected" even though I am connected, and the connection works for any other computer I attach. I get indication of proper physical connection at both ends (router and computer ethernet port), however I get no connection and the default 169 .... IP address. It does not matter if I create a fixed IP address in the router and set the ip address of the port to correspond. I have tried all the ip resets, stack resets, remove and reinstall the network ports, etc., to no avail. Connecting directly to the cable modem did not work. I even installed a new buss ethernet card with its own drivers and I get the same 'media not connected'.
View 3 Replies View RelatedMy laptop will not connect through my router anymore. I'm getting the message ( Cannot communicate with Primary DNS server (192.168.1.254). It works fine with an ethernet cable. I have a WII that uses the router also and I can watch a Netflix movie on it so the router seems to be working. My desktop computer is working fine through a DSL connection. The laptop is a Gateway and is running Vista.
View 14 Replies View RelatedI’m deploying new images on my switch 2960 24TT L. After installing the new image (c2960-lanbasek9-mz.122-58.SE1.bin) and reboot the switch I have always this error message : “Error loading "c2960-lanbasek9-mz.122-58.SE1.bin"
Interrupt within 5 seconds to abort boot process.
Loading "flash:/c2960-lanbasek9-mz.122-58.SE1.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ ”
But the switch still boot well. Why do I have this error message?
LMS installed on Windows 2003. Backup fais with message "Backup failed.ERROR(1297): Fatal error: Database engine 'UPMDbEngine' could not be started on database 'upm' in Bulk mode.."
dbbackup.log attached.
I have a WLC 2504 with 5 AP licenses for which I have installed an adder license via GUI. The installation completed successfully, but I still cannot view the new license. The maximum number of APs is still showing as 5 and in fact I cannot add more that 5 APs. I tried installing the license file again, but now I get a "duplicate" error.
View 4 Replies View RelatedAfter setting thru set time command, error message is display on server 'synthetic time issued'.
View 2 Replies View RelatedServer Error: 550 emails blocked from send.
View 1 Replies View RelatedI have three PCs in my lan. (A, B & C).I can access shared drives of B & C from A
I can access shared drive of A from C but cannot access B from C
I can access shared drive of C from A & B.
I get error message "Logon failure: the user has not been granted the requested logon type at this computer".
All the systems are Win 7, A & B are desktop and C is a laptop.I added the C's name in A's "Security Settings -> Local Policies -> User Rights Assignment -> Access this Computer from the Network" too. Still can't access.
even after installing t driver,i'm getting t same error message.Wifi adapter cannot be found
View 1 Replies View RelatedWhenever I try to goto a webpage within any browser,despite me being connected to my network(though 1 received packet to every 20 or so sent packet ratio) it tells me that DNS lookup failed. I had a similar issue on my other pc that I use more often,though connecting through WIFI momentarily resolved the issue,before I returning to wired,where everything has been fine. My other pc however has no wifi adapter. So ive been stuck.
View 12 Replies View RelatedDoes 6rd working on the DIR-601?
For example if I enter the Comcast 6rd parameters:
6rd IPv6 prefix 2001:55c:: /32 6rd border relay IP address 69.252.80.66
I then click on "Save Settings". Now I get a pop up message that says "Invalid IP address" I'm running firmware 1.02NA