Gateway LT20 Network Controller
Jan 23, 2011
I installed Windows 7 on a gateway LT20 netbook and im trying to get the driver for network controller and anything else that will allow me to conncect to the internet . This computer has the internet 3g switch .... i can get the light for 3g to light up but not the wifi one .... does that need any other drivers?
View 6 Replies
ADVERTISEMENT
Feb 6, 2011
I have just upgraded my computer and now i have a Gigabyte 870A-UD3 mobo with a Realtek PCIe GBe family Controller and i have now gotten the famous "Standard Gateway not available" or something.
View 3 Replies
View Related
Feb 14, 2013
I've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.
View 2 Replies
View Related
Aug 30, 2012
I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...
View 0 Replies
View Related
Jul 6, 2012
I picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly. What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there. For what its worth: While I have some IT experience, I don't have strong networking experience.
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site. Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up. Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected. But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me. I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
'TECHNICAL' SPECS
Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs
[URL]
View 7 Replies
View Related
Sep 13, 2012
config setup
protostack=netkey
klipsdebug=none
[Code]....
View 3 Replies
View Related
Jan 24, 2012
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
[code].....
View 1 Replies
View Related
Jul 11, 2012
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
View 1 Replies
View Related
Feb 8, 2011
we do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies
View Related
Mar 22, 2011
I have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
View 1 Replies
View Related
Oct 17, 2011
Can I have use a Gateway-to-Gateway IPSec tunnel whereby a user can surf the Internet using his local Internet connection and at the same time connect through the IPSec tunnel to a remote subnet using RVS4000 routers?
View 1 Replies
View Related
Jul 26, 2012
We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
View 1 Replies
View Related
Apr 6, 2013
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies
View Related
Apr 11, 2013
I have two Cisco RV042 Routers, they are being used to connect two offices, i have created a standard gateway to gateway connection, fixed public ip addresses on both sides and everything works fine, except when the tunnel gets disconnected, it does not connect back automatically, i have to log into either router console and click the connect button to get the tunnel working again, this is really annoying since it happens once or twice a day at least.
View 2 Replies
View Related
Mar 9, 2012
New hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway VPN
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.
View 2 Replies
View Related
Feb 11, 2012
I have a pair of RV082 routers and I'd like to configure gateway to gateway VPN tunnel as described in a cookbook, "How to configure a VPN tunnel that routes all traffic to the Remote Gateway," (file name Small_business_router_tunnel_Branch_to_Main.doc). I followed this cookbook and found that my while the Main office has internet connectivity, the branch subnet doesn't have internet connectivity.
Routing does behave as advertised, where all traffic does go to the main office. However, the 192.168.1.0 subnet in the branch office does not get internet connectivity. I've read in other posts that the Main office router will only provide NAT for the local subnet, not the branch office subnet. Is there a way to configure the RV082 router to provide NAT for all subnets?
If not, which Cisco product will provide the VPN Tunnel connectivity as well as the NAT for all subnets? Can the RV082 be used as part of the final solution or are my RV082s a wasted expenditure?
Following is the configuration that I'd implemented, (real IP and IKE keys are bogus).
Gateway To Gateway
Remote Main Office
Add a New Tunnel
Tunnel No. 1 2
Tunnel Name : n1-2122012_n2-1282012 n1-2122012_n2-1282012
Interface : WAN1 WAN1
[code].....
View 2 Replies
View Related
Apr 8, 2012
I have two Cisco RV8082 Routers which I would like to setup a VPN Tunnel with Gateway to Gateway. One location is a static IP Address. The other location is a dynamic IP address.
View 2 Replies
View Related
Aug 8, 2012
Not able connect my laptop with my college internet,ethernet cable is working properly,but when i connect the lan it says unidentified network in network and sharing center.after troubleshoot it says...default gateway is not availablei have pasted the ipconfig of my laptop...and in physical address of ethernet adapter its showin all zeroes(pls see below in bold letters)...i m not able to correct it..how can i get dat physical address[CODE]
View 9 Replies
View Related
Mar 6, 2011
I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet.
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup
View 1 Replies
View Related
Jan 29, 2012
Just bought 3 WRVS4400N, I wanted to setup gateway to gateway VPN. I followed the instructions on the WRVS4400N admin guide and VPN does not connect. I also downloaded the VPN setup wizard and that also did get the gateway connected. Everything seems to be correct. Do I have to enable anything else? Firewall setting?
Below is my config.
IPSec VPN Tunnel: Enabled
Tunnel Name: TUN01
Local Security gateway: IP only
WAN1 IP: 192.168.100.1
SUBNET: 255.255.255.0
Local Security type: subnet
LOCAL IP: 10.10.10.1
SUBNET: 255.255.255.0
[code]....
View 1 Replies
View Related
Mar 19, 2013
I am trying to set up a gateway to gateway VPN connection between a RV042G (central site) and a RV110W (newest firmware) which is used for presentation purposes on various customer's sites. The RV042G has a static IP. The RV110W has different IPs, depending on where it is used.
Basic VPN settings are clear to me (we have another VPN between two RV042G with static IPs). I set up the VPN connection on the RV042G wth the following settings for "Remote Group Setup":
Remote Security Gateway Type : IP + Domain Name (FQDN) Authentication IP by DNS resolved: mydomain.no-ip.org Domain Name: router12345
The value "router12345" is what I have configured in the RV110W as "Host name" in the network settings.
This configuration does not work so I am obviously doing something wrong. Do I have to use "router12345.mydomain.local" instead if I configured "mydomain.local" as the domain name in the RV110Ws network settings? For my tests the RV110W has a WAN-IP of 192.168.178.100 because it is located behind a DSL-Router. The external IP of this DSL-router is 178.0.x.x. The resolved IP from mydomain.no-ip-org is 192.168.178.100 but when I look in the RV042G log I see the requests coming withg the external IP (178.0.x.x). Is this the problem? The last message I see in the log is "no connection has been authorized with policy=PSK".
Or can I use "IP + Email Address (USER FQDN) Authentication" instead (where can I enter this email address in the RV110W?). Or do I have to use "Dynamic IP"?
View 1 Replies
View Related
Mar 5, 2011
I have 2 gateway over my network provider to connect to internet.like Gateway1="1.1.1.2" and Gateway2 = "1.1.1.3".but i have only one network adapter with one wire.now i want program to create "Virtual Network adapter" assigned to my real network adapter to set secondary Gateway to it, and use it by "ForceBindip".
View 3 Replies
View Related
Dec 1, 2012
My computer will only run on ethernet cable, the network can be found but only connects for a second, connects to the internet in and out, it gives the error, default gateway is not available, or problem with the wireless network adapter. The manufacturer is HP
Windows IP Configuration
Host Name . . . . . . . . . . . . : Owner-HP
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : cogeco.net
[code]...
View 3 Replies
View Related
Oct 2, 2011
I've used a newly purchased laptop, Acer Aspire 5733Z-4614 to connect to wireless networks before, including the network I'm currently on (/w another laptop), however, recently it has been unable to go through to the internet, but does successfully connect to the network. The encryption seems to be OK, since both laptops are using the same WPA2-Personal AES, and this (currently connected) laptop does just fine. I've read through a few other articles on this site but haven't been able to pinpoint the problem. To my knowledge I have not changed any settings since it has worked correctly.
[code]...
View 8 Replies
View Related
Feb 3, 2012
I have a Gateway NV53 laptop that has no problem connecting to the Internet at home, whether when it's connected with the wire, or wireless (with our own secured wireless network).
However, whenever I go in a coffee shop or anywhere else that has a unsecured network for customers, it won't connect, no matter how strong the signal is.
View 4 Replies
View Related
Mar 12, 2013
I have a cisco 3900 integrated services router. I am a little new to the cisco IOS. I am having an issue getting my LAN network to communicate with the WAN gateway. From hosts I can ping the interface IP address but not the gateway. I have used the default route command of IP route 0.0.0.0 0.0.0.0 [wan gateway from ISP] I have already set up NAT, DHCP, I just cant seem to get the internet working, the following is my config.
Code...
View 9 Replies
View Related
Apr 17, 2011
My network controller has disappeared and after months of trying to find out exactly which one I find out that this is what it is: PCIVEN _14E4&DEV_4727&SUBSYS_ 7175144F&REV_014&219A7493&0&00E1.
View 2 Replies
View Related
Oct 30, 2011
I'm still having problems (as seen in 'Network Controller Not Found (Clueless!)) and have a quick query.I'm trying to locate a specific driver and so far have exhausted my search, can I get anything from the Hardware Id from the Unknown Network Controller?
View 3 Replies
View Related
Mar 9, 2013
I just finished a new build and updated windows and gpu and mobo drivers but my internet downloads are really really slow. Next to network controller it has an exclamation mark and when I run check for updates it say it was unable to find drivers for it. My motherboard is an asus maximus v formula and I did update the lan before connecting to the internet through usb with another computer.
View 3 Replies
View Related
Aug 1, 2012
The netbook was working fine on wireless network; didnt use it for a couple of days - now I cannot conenct wired or wireless; cannot see the wired or wireless modem , only MSN dial up. But the wireless modem light is blinking steadily. Otherwise the netbook is working OK - it even seems to boot up quicker than it used to)(I would reinstall the OS but it didnt come with OS DVD or a DVD drive ; so I didnt create a backup when I bought it. I have since purchased a USB DVD drive; this is one of two identical netbooks I purchased on black Friday - other one works perfectly?
View 2 Replies
View Related
Feb 7, 2012
I can't print in my network printer using my Laptop (WIFI). I have check the default gateway of the desktop PC on which connected the printer and its different from my Laptop. Also I cant "SEE" this desktop PC on the LAN.
View 1 Replies
View Related
Sep 29, 2012
Here is my setup:
Netgear WNR2000 router.
Macbook Pro with Snow Leopard connected to router through wireless.
Windows 7 Desktop getting internet through the MBP ethernet.
I can't figure out how to be a part of my "Home Network" with my Win7 Machine so I can see other computers in my house, use my networked printers, etc. I can only see the MBP it is connected to in network panel. I want to be able to stream the movies on this computer to my iPad which is connected to the wireless router.
View 8 Replies
View Related
Jan 25, 2013
Anyway, a neighbour is letting us share their broadband by way of a wifi connection (on a very long USB lead into the front garden...) but this only works on one PC.The PC is right next to the Orange router (Brightbox) but so far I've failed to do anything like bridge the connections from wifi to ethernet to the router and beyond. Should I persevere with this? I don't understand how this would work in terms of DHCP and routing IP traffic.I'm prepared to buy new kit if necessary (but not much). Most of my equipment is wifi enabled but due to the signal strength of my neighbour's wifi you have to be on the front lawn to get a signal.
View 3 Replies
View Related