Linksys E3200 - First Ping Timeout
Oct 21, 2012
I have an issue that websites take a few seconds before they start loading, despite about 20Mbps download speeds.I've traced the problem to my E3200: when I ping a website, the first ping times out and only subsequent pings return. If I immediately ping the website again then everything is fine. After a few minutes the problem would resurface (per the specific website). This does NOT happen when I connect directly to my cable modem. This does happen both from wired and wireless devices. Happens on both Mac and Windows.
View 1 Replies
ADVERTISEMENT
Mar 20, 2011
I am running a Linksys WRT54G wireless router but have my primary computer hard wired to it while my laptop connects wirelessly. In both cases, when I ping my IP's speed test site, I get a solid ping rate of approximately 17-20ms but i also get about 5% failed: timeout's. Now I've seen posts here that suggest wireless interference could be an issue but since my desktop is hardwired into the router, that source would seem to have been eliminated. When I connect my desktop direct to the cable modem the problem doesn't occur.
View 2 Replies
View Related
Apr 19, 2012
I have an Cisco EA2700 router and a Motorola SB6121 modem. If I'm connected to the router wirelessly or through any of the lan ports, I can't visit the modem's diagnostics page at 192.168.100.1. If I connect directly to the modem, it works fine. Also I cannot ping the modem through the router, just get a timeout. My ISP is Comcast.
View 9 Replies
View Related
Nov 9, 2012
Each time I'm rebooting my E3200 device my ping to my ISP is 20ms. Few hours later the ping goes up to 300-500ms.Than I reboot again and the ping is going down to 20ms again.
View 5 Replies
View Related
Jul 10, 2012
I have 2 computers hooked up to the router via wire and wife using wireless on her laptop.I'm playing games on internet and soon I noticed I got occasionally ping spikes.. The ping get beyond 1000 - 1500 so the screen is in fact temporary freezed. Sometimes those spikes can occur with 10-15 minutes inbetween them sometimes it can be an hour or more before I notice it.I'm running Windows 7 on both my computers. I first thought it was Microsoft was to throttle the packets so I did the change in the registry. But these spikes still happen. After some testings I also notice they happen at the same time on both computers so my conclusion is that it's something with the router.
View 8 Replies
View Related
Jan 16, 2011
I know there has already been a couple of threads on this but rather than add my question to the bottom of one of those I thought I would try afresh.
We have an 857W connected to the internet via ADSL. All works very well, however if I ping from an attached PC the first one always times out. If i ping from the router (ping { URL}source 192.168.18.1) I get !!!!! every time. Back to the PC and 'Request timed out' on the first.
The only way I have been able to resolve this is by using no ip cef. It then works as expected, first ping and all. The problem is after much reading, it is not ideal to disable cef.
View 21 Replies
View Related
May 25, 2011
Getting ping timeout while using this router? (know that it IS the router tested with other routers)
View 7 Replies
View Related
Dec 5, 2011
I have setup this firewall with a NAT, everything seem fine. I try pinging from my external translate IP to the internal IP address, on the ASDM Log i can see the traffic built and teardown but on the PC i used to execute the ping it will show timeout. My configuration as belows:
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.10 255.255.0.0[code]....
View 3 Replies
View Related
Oct 1, 2012
My customer has various Cisco switches but only cisco 2950 switches has the problem of ping timeout or reply time is too long(average more than 2 sec). It will cause I Network Mangement software alarm always.
View 4 Replies
View Related
Nov 26, 2012
ASA 8.2(5), uauth absolute timeout is disabled and inactivity timeout is set to 48 hours:
timeout xlate 48:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:00:00 absolute uauth 48:00:00 inactivity
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
Users still get kicked out every 8 hours and they have to reauth. This is a logging message:
%ASA-5-109012: Authen Session End: user 'john', sid 839, elapsed 28801 seconds
View 1 Replies
View Related
Jun 8, 2011
How do I change the tcp timeout on a WRT54GS router v2 ?
View 4 Replies
View Related
Dec 2, 2012
There is anyway to change the timeout on the tcp/udp connection? So the router close the connection automatically.
View 1 Replies
View Related
Oct 29, 2012
I purchased and installed a new EA4500 wireless router. At the same time i had a new Voip phone system installed as well which i'm having issues with. The main issue is that my phones communicate with the service every 240 seconds....the issue is that my NAT timeout is below that 240 threshold. Thus my phones go in and out constantly. increasing the NAT Timeout.
View 5 Replies
View Related
Jan 23, 2008
telnet/ssh sessions time out after 30 minutes of in-activity This only happens in the case of a server that is setup behind the firewall, and of course port forwarding is used. If one unchecks the radio button for the enable firewall the sessions do not timeout at all. This is very reproducable in all recent (1.3.9) versions of RV042 and RV082 routers.
View 2 Replies
View Related
Feb 29, 2012
I was able to connect to my 5ghz and 2.4ghz networks just fine. Now today I get a message that the connection timed out whenever I try and connect to the 5ghz. I have done a 30/30/30 reset, and still no joy. The one thing I haven't done yet is a 30/30/30 with a configuration from scratch. I will probably try that later. I've done the usual things like change the channel and all that, still no go. Other things I've done, change the network name, change the MTU, restart my machine. However, this is happening on other devices as well. The 2.4ghz network, solid as a rock.
View 1 Replies
View Related
Jul 27, 2012
I've bought this router about seven months ago. I tried setting it up right when i got it but it didn't work. I ran out of time during my break and am now getting around to trying again. I've tried numerous resets and reboots, messed with most of the settings individually, but I never can connect to the internet through the router. The internet works with my old linksys router and directly connected to the computer, just not when connected to the router. I've tried calling up my internet provider, and the tech guy couldn't figure out what was wrong either. We have a DSL connection, and the MAC address of this computer is cloned into the router if that makes a difference.
View 2 Replies
View Related
Sep 15, 2011
I went out and upgraded to the E3200 a week or so ago and since then i've been unable to forward any ports. I've tried pretty much everything I can think of: disabling Windows firewall, setting a static IP for my computer, setting a static IP for the router, enabling forwarding in both single and range menus, DMZ etc.Here is a screenshot of the port forwarding page just to confirm that i'm doing nothing wrong:In the above photo you will see that I set the computers static ip to x.1.2 and I later changed it to a value that was within DHCP range as listed on the status page of the router admin gui and it still didn't work.So, what I ask of you guys is if you can think of anything that I must be fundamentally doing wrong in order for this not to work. Could it be that i'm missing some possible drivers or network utilities on the computer i'm trying to forward ports too
View 1 Replies
View Related
Aug 3, 2012
Trying to convert a spare router (Linksys E3200) into a wireless access point toextend my wireless coverage. I thought knew how to do this but having a problem.Steps I followed are:1. Disable the E3200 DHCP server2. Change E3200ip address from 192.168.1.1 to something else3. Disable the firewall4.Make wireless settings5. Connect it lan port to lan port with primaryrouter.The problem I am having is that after I finish step 2 the routerreboots with the browser trying to access it at the new ip address. But thebrowser will not connect.I am doing this on a laptop that is disconnected from my network while I am working on the E3200. It is connected byan ethernet cable to an E3200 lan port. I also tried it wireless with the same result. Browser will not connect at any ip address except 192.168.1.1 and then only after I factory reset the beast to regain the 192.168.1.1 ip address
View 3 Replies
View Related
Aug 17, 2011
the value can't be equalI am setting up a e3200 linksys for a static ip address none of the IP addresses are the same. What am I missing?
View 1 Replies
View Related
Jun 21, 2011
after messing with it for a 2 days since I got it I cant seem to get more than 130.0 my last router had 300 same setup same distance
View 9 Replies
View Related
Oct 18, 2011
I just ordered the E3200. It's suppose to ship today. I know it comes with 1 USB port for hard drives. Is it possible to connect a USB hub to the router so that I can connect more than 1 hard drive?
View 1 Replies
View Related
Sep 3, 2012
I have been using an E3200 and it has been working great. I know have a need for wireless coverage in a distant part of my house and the current router won't get there. I also need wired in that spot of the house as well. I thought to buy a e1200 to use it as a WAP for that part of the house and also to have a few Ethernet ports come off it. Can I connect to my original E3200 wirelessly from the e1200 and then use the e1200 as a WAP and for Ethernet?
View 7 Replies
View Related
Nov 13, 2012
I just upgraded my router from 1.0.03 to 1.0.04, I have a few questions:After installing the firmware, I pressed the reset button at the back for almost 1mn, the power lighted as expected, I then unplug the power cord for 30 sec.The strange thing is that this did not lead to a reset of the configuration, all my settings are still here...!But the actual problem is that my internet speed is divided by two, I still have to confirm this observation on the long term.
View 1 Replies
View Related
Feb 18, 2012
I have to reboort my router every day to get back an internet connection? I have a desktop and a laptop plus iPads, etc. The laptop loses connectivity every day about the same time. My only solution so far is to reboot the router. I realize that the client lease time is set to 1 day by default but isn't it supposed to ask the modem for another day of life when this happens?
View 5 Replies
View Related
Jun 15, 2012
I'm using a DSL line that changes IP's. I have the E3200 set to auto, but everytime the IP changes, my internet goes down, and I get an ip of 127.0.0.1 on the status page. I then have to renew the ip and reboot. This happens once a day, usually.
View 3 Replies
View Related
Jul 6, 2011
I have a 6 year old wrt54g that is working fine but old. I want to upgrade and will go with the 3200 or 4200. I really don't need the extra features on the 4200 since everything I have is hardwired (directly to two laptops and to two switches in other parts of the house for tv and printer). I want wireless for times when we move a laptop but it wouldn't be all the time, and we won't (for now) use the media options. The difference in price between the 3200 and 4200 is less than $25 so costs is NOT a factor in deciding.So should I just purchase the 4200 since price is not a factor or go with 3200; I want the most stable of the two and will never need the extra wireless features in the 4200.
View 8 Replies
View Related
Jan 11, 2012
I used to have a Belkin router which was losing connectivity throughout the day for a few short moments. After looking at the logs it appears it was issueing a DHCP release randomy which explained the fault. Since it was old router I decided to replace it with a E3200. This worked fine for a few days but then I started to see similar symptions. So currently I am trying to figure out if it's the same issue as before. I tried looking for a log on the router to see if it was also losing/releasing the WAN IP, but apparently the router doesn't log it. I spoke to a tech rep on chat, but I don't think they understand what I was talking about (how frustrating). I even tried to explain it another way that if I hit the 'Release IP address' button and then hit the "Renew IP Adresss' button does this activity get logged.
Where can I find a log to see DHCP activity (on the WAN interface)? There is a DHCP log which shows all the LAN activity but this is not what I need for this issue. I find it hard to believe a mature vendor like Linksys doesn't log this activity?
View 3 Replies
View Related
Apr 19, 2012
House has 2 floors. I want to install 2 E3200, one on each floor, but both with the same SSID/Password, etc. so internet connection/streaming throughout the floor is seamless.
Both floors have network wall sockets ready and they all lead to the same modem/router so all devices plugged lead to the same network.
PS. both E3200 have been update to Firmware Version: 1.0.03
View 9 Replies
View Related
Aug 28, 2012
I have bought Linksys E3200 less than month ago.I have setup it, connected HD (WD My Book 1TB) through USB and it work good, without any problem.Than week ago, I turned off the router, because of my vacation. Yesterday, I came back, turned on the router. WiFi was working good, cable connection too. But there was no connection to HD. I had checked information about HD on admin page, router understood that it is HD, but not provided share access to folder, also, there was no button, to setup it.I disconnected HD, tried to connect it using the Cisco Connect, it provided mistake with USB connection to HD and than with HTTP connection to router. I disconnected HD, tried to connect it manually: connect HD -> go to admin page -> refresh to show HD -> admin page freeze... -> reboot of router manually.
There was a lot of tries to connect HD, but all was failed.I connect HD to computer, it works successfully.I checked connection to router through USB, using my card reader and SD flash card, it works successfully.Information about HW:
1. Linksys E3200, last update of firmware for German (was bought using German Amazon) country. (Cannot check it now, if needed will check)
2. Computer: Windows XP SP3
3. WD My Book 1TB (NTFS)
View 4 Replies
View Related
Jul 29, 2012
I updated my E3200 to 1.0.04 to try to resolve a wireless dropping issue. Now the connected USB storage no longer responds correctly (very delayed if connecting at all). When I try to provision new storage via the routers admin page, I do not get the permissions page.
View 9 Replies
View Related
Jan 24, 2012
I just picked up the E3200 and love it. This morning I hooked up my printer via the USB. Everything went smooth until I tried to print something. I thought nothing was happening, but I let it sit for a while. While I was waiting, I was messing around with my network setting in windows. I realized that my network had been set to 'work' for some reason, so I changed it to 'home'. As soon as I did, my printer spit out my test page. (probably 5 min after sending the doc.) I don't know if it was just coincidence or what, so I sent another page and nothing happened (yet).
Is this common to take that long? Is there a way to speed this up?
View 3 Replies
View Related
Jan 4, 2012
I have a Linksys E3200 router with a USB port on the device. I have connected an Epson Stylus Photo R380 printer directly to the port. I have an iMac 27� connected to it by wireless. I have a PC workstation connected to it by cable. I have 2 laptops connected by wireless.I downloaded the Cisco Connect for the PC and 2 laptops. The PC works great due to being connected by direct cable. The 2 laptops will not recognize the printer connected to the router. For the laptops, I click on Add Device, Printer in your Home, USB printer (it says connect a printer to the USB port on your router), I wait while it checks for drivers, it finds the printer and when I print a test page, I get nothing but the printing error. I can connect the printer to the laptop and it prints just fine.
I downloaded the Ciscon Connect for Mac. Loaded it and it went through the setting up my router. Congratulations! I am now connected to the Internet. Click on Computers and devices to add the printer. Well, my options are Computer, Wireless printer (where is the USB printer option that is shown for the PC), Other wireless devices or USB storage. Well my first choice would be Wireless printer. Next screen is Connecting a wireless printer showing the network information. Click next and wait. Well, it says a wireless printer is not found. I click Finish to get back to the Computers and Devices to make another selection, as in computer. Select Connect Manually using my wireless settings. Another box saying it is connecting a device and gives the network information. Again I wait! It says device not found.
View 12 Replies
View Related
Oct 31, 2012
My Linksys E3200 has no wireless access to the internet. Wireless devices show they are connecting to the router, but cannot access the internet.
The router had worked fine until suddenly no internet access. Mac network diagnostics show that the connections are correct until the ISP and Internet which show either yellow or red.
The router's homepage shows no changes in configuration. Ethernet connection works fine.
View 6 Replies
View Related
