I have a linksys WRT54GL with the latest firmware. I know QoS feature can limit bandwidth based on priority. But QoS feature is only for wired network, is there any good ways to limit bandwidth?
View 14 RepliesWRT54GL has an option to restrict or share the bandwidth equally to each ethernet port or wireless? I need this option in a low bandwith area because the first computer connected to the router who makes some traffic (e.g. youtube) takes all the bandwith allocated by the ISP. url...
View 1 Replies View RelatedI have a Linksys WRT54GL v. 1.1 that has been dropping connection speed (starts at 54mb, then drops to 48mbs, 36mbs, 28mbs, down to 1mbs) then disconnects, then reconnects at 54 mbs. After a short while, it will drop the speed again until it disconnects and reconnects again. This is the third Linksys WRT54GL that has done this. The first one was 5 years old before it started doing this in February, the second was 3 months old, and now the replacement Linksys sent to me is doing this?
What is going on with my router? I am able to connect fine with the Cat5 cable, but wireless seems to be the problem. Even my phone(s) get disconnected from the wireless router. This problem just recently started and I don't know why, no settings had been changed on any of the routers until after the problem had already ocurred, then the Linksys phone tech support had me make multiple changes.
I'm wondering if there is a way to prioritize traffic on the router's main WiFi over the guest zone or if there is a way to limit the bandwidth on the guest zone.
Ideally, I'd like to keep a locked primary WiFi for high-speed usage (I know, nothing it really ever secure) and an open guest zone for low-speed usage to whomever wants it. As far as I can tell, the DIR-655 doesn't support this kind of configuration.
Just put in an SF302-08P switch with two AP541N's. Just a Comcast modem connects into the switch along with the two WAPs, nothing else. Speedtest through the cable modem with nothing plugged into it is 48Mbps. Then connecting a single laptop via the switch shows a speedtest of 33Mbps. Then with the two AP541N's plugged in and using the same laptop over WiFi, I'd consistently seen 10Mbps for downloading. But going right back to the cable modem directly showed me close to 50Mbps in a speed test.
Have factory defaults in all the Cisco devices, and poured over the settings and it looks like bandwidth limiting is disabled. Suspecting maybe it is for QoS and to optimize voice, but I see definite places in the devices where I could designate optimizing voice and those aren't enabled. Then started thinking with tweaking the wireless frequencies, but didn't want to do anything too unstable.
I have a Cisco Aironet 1240AG Access Point and I am trying to setup a guest network that is secure and limited in bandwidth utilization. I see an option under security > SSID Manager on the web interface to select an interface of Radio0-802.11G, Radio1-802.11A or both. Can I put the guest network on the Radio1-802.11A and make it more secure/bandwidth limited or does this option not matter?
View 3 Replies View RelatedI have a Linksys WRT54GL wireless G router and I just brought a Roswell Wireless N card. would these two items be compatible with one another? or would I need a new router/adapter?
View 4 Replies View RelatedI have both a Sony XBR52HX909 and a Sony BDP-S580 connected to my router (WRT54GL)via ethernet. When I try to connect to the internet, both show the wired connection as good but neither can connect to the internet. The BDP-S580 also has wireless connectivity, but it can’t connect to the internet wirelessly. I have two desktop computers connected via ethernet and two laptops connected wirelessly to the same router and all have internet connectivity. I have tried the “auto” settings on the TV and Blu-Ray player and also tried entering the network information in manually. I still can’t connect to the internet.
View 5 Replies View RelatedLast week suddenly my internet connection failed. I have tried several times to establish the wireless internet connection. Everytime when i tried to do this, i get the message 'can not get IP address'. Already tried to upgrade the firmware but still same message appears.
View 4 Replies View RelatedI want to use my router to boost the signal to the 2nd floor of my house, and Im having some problems.When I connect my router to the web application to change restore it to manufaturer setting the router keeps broadcasting my old SSID. The laptops in the house pick up that signal. I want to reset my router so it can broadcast my new network.
View 2 Replies View RelatedI have Wireless-G Broadband router Model WRT54GL. Everything is all setup correct but consoles and handhelds can't get the IP address even if there connected to the router. It isn't intill I turn off and then it back on does it get the ip address.
View 2 Replies View RelatedI'm trying to use a WRT54GL with U-Verse. The problem is that the router does not get a connection to the modem. It can't ping the modem, and it doesn't show up on on the list of devices connected to the modem. DHCP assigns an IP address of 127.0.0.1, which is outside the range of the modem [192.168.1.1 ... 192.168.1.253]. The router is also showing a default gateway of 0.0.0.0, and a subnet mask of 255.0.0.0. (And yes, I have released and renewed the lease, rebooted the modem, and reconnected the modem.) The router WAN side is set to DHCP, and the operating mode was changed from gateway to router (the gateway setting doesn't work either, for that matter).
View 9 Replies View RelatedI currently own a LinkSys-WRT54GL 802.11a/b/g wireless router, and my ISP is Comcast Cable providing me with 15 Mbps (that's bits per second, I believe) download speed. I am wondering if there is any benefit with using an 802.11n wireless router to access the Internet? The maximum theoretical speed of the WRT54GL router is 54 Mbps (802.11g), which is faster than the 15 Mbps provided by my ISP.
I know that 802.11n has a max bandwidth of 300 Mbps, and it would work for intra- house transfers, such as streaming video from one computer to another.
But is there any benefit to 802.11n for Internet activity, such as web browsing, gaming, and streaming video from Netflix.
I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet.Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times. Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this. How to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router
View 4 Replies View RelatedI have a brand new TMG Installed and setup some rules. But i need to have one wireless router for a special office which should not be filtered by TMG. How can i setup TMG rule and the wireless rounter to not be filtered on TMG ? The linksys wireless rounter should also NOT ask for domain authentication.. it should allow directly access to outside without any authentication.
View 1 Replies View RelatedI recently had to unplug my Linksys WRT54GL wireless router when doing some rearranging and now i'm unable to get a internet connection. I've confirmed the modem is actually working by connecting my laptop directly (which worked), but when I connect the Linksys WRT54GL wireless router to my modem the internet connection goes away. The connection is lost when connected via wireless and hardwired to one of the back ports. I've tried resetting the modem, router and computer and read every forum out there trying to find something, but i'm still stuck.
View 5 Replies View RelatedI have a problem with my linksys WRT54GL router. I entered here [URL] and i set it up, i can connect to internet on my PC and wireless works great but i can't set wireless password and name. When i go to the wireless tab, i write the new name but when i hit seve setting i get disconnected from internet. I try to go to status and click on Connect tab, when is connected internet works but the name and the password of the wireless that i set earlier is reset to default. What do i have to do to set name and password and have internet at the same time.
View 7 Replies View RelatedI would like to connect my old WRT54G3G router to my new WRT54GL (connect to dsl modem) and have wireless on both activated.I have set both on different channels with same SSID and same passwords on WPA2 Personal AES.I have also made the network IP different WRT54G3G 192.168.0.99 and WRT54GL 192.168.0.98.I have also deactivated network DHCP on 192.168.0.99. and Operating mode to router and still not working.
View 1 Replies View Relatednot being able to block websites like facebook and youtube on the router.
View 4 Replies View RelatedI am using a WRT54GL for the free wifi service at my business. Is there any way to set it so that when someone accesses the internet they are directed to my business home page first?
View 1 Replies View RelatedI want to use a linksys router with a 3com switch. 3Com model 3CGSU08A.i have two routers to choose from a E2000 and a WRT54GL which one is better and settings to use.
View 1 Replies View RelatedWe have received from a customer of us an WRT54GL box configured with a Coova software. This Wifi router was supposed to be a Wifi hotspot, but was not configured by us. This box is able, on startup, to get an IP by DHCP, to touch a remote Radius server, and so on (we "tcpdump" the Internet traffic, and we saw DNS requests, radius requests, ...)...
But, we are unable to connect to this box,by SSH or by HTTP, either by plug-in PC to the Internet RJ45 or the LAN RJ45. It has no IP as 192.168.1.1. Instead, it was configured to have 192.168.1.1 as gateway.
Of course, we have no doc on previous install, but only the admin/root password for SSH.We are afraid to lose the config (coova, ...) if we perform a hard reset.What is the best way for connecting on this box ?
Why this router have DHCP server and Port forwarding features and many LAN ports, but does not have DHCP reserve feature? If I can plug many computers, each one get own IP address, but how I can't fix it? I need to port forwarding of course, but if lease time ended, next time my computer got other IP address, so I need to reconfigure port forwarding each time! Of course I can do it, but try to explain it for your wife? Yes, I can use static IP addresses, but for what this box have DHCP server?
View 9 Replies View RelatedI accidentally pressed the front panel button labeled "Cisco Systems" on my WRT54GL wireless router. The button turned to a flashing white which I understand means that it entered SecureEasySetup mode. I then power cycled the router and the front panel button turned back to solid orange. However, now the "WLAN" lamp flashes a lot more often than before even when there are no wireless clients connected. It doesn't seem to be affecting connectivity or performance of my Ethernet connected devices or wireless connected devices. I re-entered my SSID and security key. That didn't curtail the increased flashing of the WLAN lamp. I also tried pressing the front panel button for 5 seconds. This only cleared my wireless settings.
View 2 Replies View RelatedI have a 16mbps (megabits) cable modem that is connected to WRT54GL. Desktop is located next to router and is connected with a cable, Laptop is connected on Wi-Fi. Both PCs achieve maximum speed when downloading from the internet but when I try to copy something from one PC to another over the local network I get stuck on max 2.5-3MBps (megabytes).
View 4 Replies View RelatedI'm using a WRT54GL(4.30.14) Router with a Charter Cable Modem running 5 computers on the network with 1 being wired and the rest are wireless. When my family comes over they can connect with their iPads and laptops but for some reason I can not get this iPhone 4G to connect. We put in the password and it says unable to connect. Are there any special settings that need to be made to the router to let the IPhone connect?
View 3 Replies View RelatedConnect my linksys WRT54GL router to the proxpn vpn privacy service as a client? (or any other vpn privacy service for that matter) I already have an internet connection up and live with a cisco router so I would need to connect the linksys to the cisco and use the linksys as a vpn gateway kind of thing, so that any computer connected to the linksys will automatically be in the vpn tunnel without needing any cleint software installed on it. The vpn service I use is proxpn but they won't support the settings of individual routers (understandable). The only setting they give for a PPTP connection is here
[url]...
I've had a WRT54GL ( for about a week now ) with no real issues. Today my wife mentioned that the net's been flaky ( wireless nto hard wired ). I originally noticed what seemed like minutes for my desktop of laptop to connect to any web pages. Loads were extremely slow. According to the computer I had a 1 mbps connection. I did the standard resetting of the modem and router.babble babble babble. Eventually, I ran a wifi analyzer from my phone to determine an ideal channel. However, while running the frequency scanner I also noticed that my broadcasting would continue to drop off the radar for a quick moment then return. This seemed to be true no matter what channel I set. What's interesting is that the signal would read as extremely strong for 45 sec - 1 minute, then completely drop the signal, then another strong broadcast. Other neighboring signals don't exhibit this behavior....well I would see the weaker signals coming in and off the radar from time to time. I'm guessing it's some type of interference? However if that's the case I can't explain why my signal seems so strong. I'm assuming I'd see a lot of fluctuation in my signal before dropping off ( instead of going from 100 to 0 in the blink of an eye ).
View 1 Replies View RelatedI have a wireless router and I'm trying to user UPnP feature. of course it is enble in the router.
It's working one and after it stop working, looks like the router is not responding anymore. If I got on the web interface of the router, I loging, on the first web page I press save changes, even if I didn't change anything, the UPnP feature work again.
Looks like a timeout occure or something like that. Is there a way to wake up the router without having to go on the web interface? Why it's stop working?
Firmware Version: v4.30.15
Router is setup as DHCP and only allows 7 IP address leases that expire daily. Lease time is set to 0. I have the latest firmware. Until recently when our family started using Apple iPhones (2 of them), I didn't have this issue.
Now I'm having a problem where my clients table will show leased IP's with no devices attached to them. I have to clear those no-name addresses so that the iPhones and other non-Apple wireless devices in the house can re-establish a connection.
How can I get those IP's to be removed without having to constantly log into the router and clear them?
I have two WRT54GL wireless routers. I have a computer and printer in my office connected to one of them. I'd like to add a computer and printer back in the shop to my network without using a wired connection. Can I use the 2nd wirelss router so that all computers and printers are on one network?
View 6 Replies View RelatedI had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet.Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times.
Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this. how to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router.
I tried setting up a home network with my above Linksys router and can't connect to the internet now. I have the ethernet cable from my DSL Modem hooked into the ethernet port on the back of the Router. In port one, I have a cable which attaches directly to my laptop as I was advised to use a cable for initial setup of my home wireless network. I was able to get into the router to set all the passphrases and wireless security settings, etc. My ISP is PPPoe and I have entered both the UserId and Password that my ISP provided. However, upon clicking on the wireless icon, my system states I am connected but the status screen shows "No internet access". I have no problem connecting to the Internet when the cable runs from my DSL modem into my computer, so it's something to do with the router blocking it now.
My ISP does not support my Linksys router, of course, and they tell me I need to contact the manufacturer telling me the router needs to be set up as a 'bridge" ??? There is no mention of anything like this in the manual and I do not know if there is a setting on the router that is somehow blocking my being able to get an internet connection. This is all still with cables attached. Again, I seem to be able to 'connect' to the wireless network but I now cannot get to the Internet thru the router...