Linksys Wired Router :: RVL200 Locks Up When Using Logmein?

Sep 18, 2011

I have two new RVL200's with 1.1.12.1 firmware on it.  Every time we use Logmein to remote a pc on the LAN it locks the router up and has to be power cycled.  I have reinstalled the latest firmware 1.1.12.1 and this has not worked.

View 1 Replies


ADVERTISEMENT

Linksys Wired Router :: Get IPSec Connection With 2 RVL200?

May 15, 2007

We have a main and branch office, each with an RVL200 . I configured both with static IP's as provided by my ISP, yet when I try to do a test connection on the IPSec screen I just get that it's "waiting for a connection" in the cell third from the left. Both RVL200 's are connected directly to the modem/bridge supplied by both ISP's.

View 5 Replies View Related

Linksys Wired Router :: RVL200 Stops Responding

Jan 17, 2011

Bought a Cisco RVL200 (latest firmware included - I checked), and I've set it up to serve as the gateway/firewall for my home network. I also intend to use the VPN functionality when travelling as well as serving up content from a web server behind it. All of this seems to work the way it is intended (after quite a bit of fiddling).
 
The problem however is that if it comes under any sort of load it simply stops responding - physically it looks alright with the expected leds being lit, just as it would when functioning normally. It does not display the management interface, nor does it even respond to ping (which it does when it works). If I start up a bittorrent client on any of the machines on the internal network and add a torrent to something popular like Ubuntu Linux it'll usually start downloading and then after 5-15 minutes the RVL200 will have stopped responding. Tried adding QOS settings to limit the computer running the client or downprioritize this type of traffic, but that does not seem to have any effect.

View 1 Replies View Related

Linksys Wired Router :: RVL200 Block Specific LAN / LAN Traffic

Jul 25, 2011

if the firewall rules in the RVL200 work for inter LAN routing as well as LAN<->WAN?  I need 2 separate networks in a house, 1 for business 1 for family, and I want to only allow my IP on network 1 (family net,10.0.0.0/24) access to network 2 (business net 10.0.1.0/24).  I want this as if I change rooms were a access point for business is not available I can use the home net and specific IP to access certain business net IPs.   I saw you can turn inter vlan routing on or off, but it wasn't clear on firewall rules.know of a similar router in cost but with gige instead of 100Mb ports?

View 1 Replies View Related

Linksys Wired Router :: RVL200 - Java Applet (No Connect / Disconnect Buttons)

Apr 4, 2011

I got problem with RVL200, it works good on my botch mac's witch OSX 10.5,10.6 and Firefox 3.6 but stops working after last java update. The machine switch 10.5 is working because I don't update Java but the other computer is up-to-date.

Problem is with launching the Java applet ,all the rest is working.- I'm log in to SSL VPN Tunnel- The new window is opening I accept applet to run .It try but nothing happens the window is blank with no connect / disconnect buttons.

All I have is Java error:Plug-In Java 1.6.0_24JRE version 1.6.0_24-b07-334-10M3326 Java HotSpot(TM) 64-Bit Server VMjava.lang.SecurityException: [code]....

View 1 Replies View Related

Linksys Wired Router :: RVL200 / RVS4000 Possible To Assign Public IP Address As Local IP Address?

Feb 28, 2011

Is it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?

View 1 Replies View Related

Linksys Wireless Router :: E1000 Periodically Locks Up

Mar 26, 2012

my E1000 router locks up and I lose Internet connectivity until I unplug the router's power cord, wait for 10 seconds or so, then plug it back in and let it restart. This seems to be triggered (a.) when I land on a web page with intensive graphics, etc., that takes a while to load, or (b.) if I launch a web page really quickly while another one already is up. it doesn't just happen spontaneously when I'm working on the computer. This computer I'm working on is old and slow, which is why as per my earlier inquiry about having to reconfigure the router and network , I'm looking at changing to an up to date and faster model. I just updated to the latest firmware, probably a week or so ago, but the router was doing this before then and still is doing it now.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G Locks Up When Connecting Wirelessly?

Feb 27, 2012

My WRT54G  router locks up 100% of the time when attempting to connect connect wirelessly to a Samsung Blue Player (Model number BD-P3600). I can connect to it with a cable no problem, but when I attempt to do so wirelessly and type in the password on the Blue Ray player, it attempts to connect but the router locks up and all devices connected to it (wired or wirless) lose connectivity

View 1 Replies View Related

Linksys Wireless Router :: E4200 Locks Up In Bridge Mode?

Feb 7, 2012

I'm using the E4200 in Bridge mode and it's handing out IPs from our DHCP server (not acting as it's own).  I have about 8 people connecting to this wirelessly to get to our network.  For some reason it locked up once every week or two and I have to unplug it (can't even remote into it).

View 3 Replies View Related

Linksys Wireless Router :: E4200v2 Locks Up / Freezes Regularly

Jan 5, 2013

My e4200v2 which I have been using for about 4 months locks up or freezes regularly - as often as once or twice a week. That is to say the wired laptop can't reach the router and the smart phone does not have a signal. This often happens when there is no phone or computer running. My current firmware is 2.0.37 and it just happened again. The logging capability is absolutely terrible so  you can't tell why or when it went down, and what happened just before it went down. I pull the plug on power and when it comes back the log is clean. avoid the freezing/lockup or for logging incoming and outgoing with timestamps?

View 1 Replies View Related

How To Tunnel Linksys RVS4000 To RVL200 IPSec

Dec 26, 2010

Linksys Small Business VPN endpoint routers?

I have been trying for two days to setup a Linksys RVS4000 to a RVL200 IPSec tunnel and I can't get them to connect.

The internet is via optimum online home internet accounts. From what Cisco said, the ports necessary are 500, 4500, 443 and 60443.

View 17 Replies View Related

Linksys Wireless Adapters :: AE2500 VM Locks Up For Awhile Then Comes To For A Moment

Feb 4, 2013

I have a AE2500 USB Adapter.  Whenever I go to connect it from my host machine to my VM I receive a Code 10 Error in Device Manager(Device Cannot Start).  The VM locks up for awhile then comes to for a moment.  Problem stops when the USB adapter is removed. 

View 5 Replies View Related

Cisco Firewall :: ASA 5520 For Blocking LogMeIn And GoToMyPC

Sep 1, 2010

How to block LogMeIn and GoToMyPC?  We are using an ASA 5520.  We mainly want to prevent people coming into our network using those applications.  Also, our helpdesk uses LogMeIn Rescue and would need to allow that for them. 

View 6 Replies View Related

Linksys Wired Router :: EA4500 - Wired Connections Have Long Ping Times

Sep 23, 2012

I purchased and set-up the EA4500 on Thursday.  Friday my ISP (Charter) was out and worked on connection for over 2 hours due to slowness issues.  Connected directly to modem I get normal ping times on whichever computer is connected.  When I get the computer connected by the router (hard wired) I get very long ping responses up to 900ms.  They are all over the place 30ms (I can live with that), up to the 900's.  I contacted Linksys support last night, who had me update to the cloud firmware and change MT U to 1300, have not noticed a difference.  I did end up doing a hard reset on the router last night after I lost tech support.  We were disconnected with router rebooted, and I didn't have the patience to connect again last night.
 
It was so slow on my work computer, a pint to yahoo timed out.  The computers connecting to router are
 
XP SP3 (mine)
Win 7 Home (IPV6 turned off)
Work laptop that uses VPN and VOIP

View 5 Replies View Related

Linksys Wired Router :: E2000 - Security Wired Ethernet Connections

Sep 19, 2011

I have an e2000 wireless router and have several devices connected by ethernet cable including private data on an external hard drive.  I am planning to allow a tenant in another building connect via an ethernet cable connected to my router.  Can I limit that computer (tenant's computer) from accessing all other devices connected by ethernet cable to my router?  I know can password protect wireless access and limit access to the internet that way -- but my question is specifically to connections by ethernet cable.

View 1 Replies View Related

Linksys Wired Router :: E4200 No Longer Accepts Wired Connections?

Oct 11, 2012

My E4200 router no longer accepts any WIRED connections. I can connect from the modem to the computer and everything works as expected. I can connect other computers wirelessly to the router. I cannot connect any laptops WIRED to the router. Nothing has changed on the systems to restrict internet access. There is something wrong with the router and the WIRED ports. I tried going through the troubleshooting on this site but it was of little to no assistance. The Cisco Connect utility doesn't appear to accomplish anything either. My guess is because I cannot connect to the WIRED ports on the router to connect to the internet to allow for whatever troubleshooting that needs to be done.

View 2 Replies View Related

Linksys Wired Router :: BEFSR41 Two Wired Routers In Non-standard Hookup

Sep 14, 2011

I have a home network with a wired BEFSR41 that, for a variety of reasons, MUST be manually IP configured (DHCP off).  All computers and other devices connected to it are manually IP configured.  I desire to add a device that cannot be manually configured, and needs DHCP.  I therefore need to daisy-chain two routers with the second one DHCP on (and manual IP connection to the main network).  The new device needs two-way internet access, but doesn't care if it sees any other current network devices.  I've tried several configurations, none seem to work.

View 3 Replies View Related

Linksys Wired Router :: BEFSR81 Keeps Losing Wired Connection To WAP54G?

Apr 11, 2012

I have a WAP54G in my basement shop, wired to our main router upstairs, which is a Linksys BEFSR81.  I'm not sure if this is an issue with the WAP or the router.
 
I only use the laptop computer in the shop every couple of days, but I leave the laptop plugged in and on most of the time.  I used to have the power settings such that it didn't power down completely even after a long time.  With that setup, if i didn't use the computer for several days, it would find that the connection to the router had died.  The wireless link would report that it had a solid connection, but I couldn't connect to anything.  Power cycling the WAP always fixed this.
 
Recently, I decided to save some wear & tear on the laptop drive, and adjusted the power settings to go to standby after a couple of hours.   Now, it seems I can't even go one day without losing my connection.
 
I am running the latest frimware in the WAP, and the router is version 3.1.  I can't check the firmware version on the router at the moment, because the web interface is giving me a blank screen.  I know from past experience that I will have to power cycle it to get it to talk to me again. 
 
In any event, it seems like the router connection to the WAP is timing out.  I set the router "client lease time" up to 10000 a while back when I first had this problem, but that is clearly not doing the trick.

View 3 Replies View Related

Cisco Firewall :: ASA 5505 / Block Internal LAN And Internet Traffic Except LogMeIn Site?

Sep 12, 2011

I have configure Cisco 5505 as layer 2 firewall mode. I have vendor machine connected  to Cisco ASA 5505 on port 2 as VLAN2 inside then VLAN1 outside connected to my internal network on layer 2 cisco 2960 switch. This machine needs access only to LOGMEIN then block all internal/internet traffic. 
 
vendor machine on vlan 2 inside >> Cisco ASA 5505 vlan1 outside  >> layer2 switch >> internal LAN >> Cisco 5520 main FW >>> INTERNET

View 1 Replies View Related

Wireless Router Randomly Locks Out Devices From Connecting

May 30, 2012

Wireless router started randomly not allowing any wireless devices to connect to the network. A wired cable worked fine, but not wireless. So we had to unplug the router and then it would work fine.You could see the device, but not connect. We moved our wireless phone a little farther away from the router thinking it was interfering, but still no luck. It didn't matter if it was an iPod, our BluRay player, or a laptop.

View 1 Replies View Related

Linksys Wired Router :: BEFSR41 - Convert Wired Router To Hub?

Jun 16, 2011

I have an old BEFSR41 ver. 2 wired outer that I'd like to use with a motorola modem/router as a hub.  Is this doable?

View 2 Replies View Related

Cisco VPN :: RVL200 As A PPTP Client

May 22, 2012

I'm trying to set up a permanent VPN connection for an Expat. We've got an RV042 set up on site to act as the server, and an RVL200 as a client. This RVL200 will be behind a home router, so it needs to initiate the connection every time; the site side router won't be able to see it behind the Expat's home router.I've got a PPTP server set up on the RV042, and I'm trying to get the RVL200 to connect to it as a client. Is there any way to do so, or will we need to go with another option? Because on the RV042, I see no way to set up an SSL server of any kind; only a direct SSL Tunnel, which won't work as again, the RV042 will not be able to see the RVL200.

View 1 Replies View Related

Cisco Routers :: Putting A Vpn Server Behind Rvl200

Jan 6, 2013

rvl200 is not working with any new os/java.  cisco is not fixing and telling us to move on.picked up a vpn server and placed it on the dmz for rvl200 (on 192.168.1.105).  for the life of me, can not get traffic from the outside to go to this server.  tried port forwarding on rvl200 (for 443) which is what the vpn server recommends.  rvl200 is not allowing this.  can not go through the ssl vpn on rvl200 since it does not work.  looked at rv042 topics and it shows similar problems. 

View 1 Replies View Related

Cisco Routers :: RVL200 And Windows 7 Do Not Work

Dec 8, 2011

Tried everything .... beginning with updating to actual firmware, installing C++Redistr and all other tips I found.eg there are no ssldrv.* in the assumed directories .... there is a certificate which is outdated in the 1920th (lol) ... it´s true.Phone support is not avail .... because we use it a couple of years .... with xp and vista there is no prob?Perhaps there is a usefull handout/whitepaper available? I´ve followed this link, but that did not work:[URL]

View 1 Replies View Related

Cisco Routers :: RVL200 SSL VPN After Java Update

Apr 4, 2011

I got problem with RVL200, he works good on my botch mac's witch  OSX 10.5,10.6 and Firefox 3.6 but stop working after last java update.  The machine witch 10.5 is working because I don't update Java but the  other computer is up-to-date.
 
Problem is with lunching the Java applet ,all the rest is working.- I'm login to SSL VPN Tunnel- The new window is opening I accept applet to run.He try but nothing happends the window is bank with no connect / disconnect buttons. [code] I have all the rights / permission to vpclient catalogue and files in there.I try this on root to the same error

View 12 Replies View Related

Computer Locks Up When Wireless Drops?

Feb 12, 2013

Every time I use internet applications, browsers, game clients, games, etc. the computer will completely lock up and I am required to manually reboot it. All devices stop working and the only way to get it working again is to hard reset. I'm so fed up with it, and have tried virtually everything. On top of that, I am getting only 1-9 Mbps download speed, opposed to all my other wireless devices, which are getting 34-36, which is what my wired connection is.

Here are my specs:
Core i5 3570k
16GB DDR3 Corsair
1000w Kingwin
Zotac 4gb GTX 680
240 Sandisk Ultra SSD
z77 AsRock Extreme 4 motherboard
D-Link DWA-556 Xtreme N Wifi Card
Windows 7 Professional x64 bit

Also, When first installing the card, I used to get around 34 Mbps, as this started occurring just in the past week or so. It works fine in other computers though and my signal strength is showing 100%.

View 3 Replies View Related

Cisco Wireless :: 1552E Rap Locks Up

Aug 21, 2012

1552E Rap will "lock" up, and not allow MAPs to connect through it to join. the WLC.  Rebooting the Rap will resolve the issue, but the problem comes back and some random point in the future.  Prior to rebooting the Rap to fix the issue, the Rap shows as joined to the WLC, but I have noticed that the neighbor details look stale, meaning my MAPs don't show up as neighbors, but other MAPs in the area are in the neighbor list, listed by MAC address.  At this time, I can not confirm whether or not the neighbor detials are changing (updating), but I can confirm that my MAPs never show up as neighbors.As soon as the RAP is rebooted, MAPs join the controller again.

View 3 Replies View Related

Cisco Routers :: RVL200 With Windows 7 Ultimate And IE 9 SSL VPN Not Working

Jan 29, 2012

How to get the Virtual Passage adapter to install and the VPN to work, I keep getting the install error for the Virtual Passage Adapter.  I have the last and latest firmware installed, 1.1.12.1 and am running Win 7 Ultimate 64-bit.  I previously had it working from within the same building where I am now in but somewhere in the IE upgrades or otherwise the adapter no longer installs.  I have tried starting IE9 64-bit with administrator's rights, made the noted ActiveX and scripting security changes as noted in the manual for a Windows OS.  I also have C++ 64-bit redistributable 2005 installed (also 2008 and 2010 for that matter if that would cause any conflict).  I am running Norton 2012 Internet Security and SUPERantispyware which I don't think have any bearing on the situation but still thought I would note it.  I do not have port 443 forwarded for any reason in the RVL200 setup which I learned RVL200 uses for the SSL VPN.  I have tried removing the SSL drivers that were put in the Windows folder after the failed attempts of the Virtual Passage instal but with no luck in reinstalling.

View 2 Replies View Related

Cisco Routers :: RVL200 SSL VPN - Cannot Access Remote LAN With IPad2

Oct 9, 2011

RVL200 firmware 1.1.12.1 iPad2 cannot access any device on the remote LAN despite the closed padlock icon.Is there another App needed ? Or how to debug the SSL VPN ?

View 2 Replies View Related

Cisco Routers :: RVL200 Virtual Passage On Android

Sep 19, 2011

i have an rvl200 Router and the ssl-vpn-tunnel is working fine under windows and linux.Now i bought a Nexus S with Android 2.3.3 and would like to create an vpn- connection to my router too.But the Applet, like on linux is not starting.

View 2 Replies View Related

D-Link DIR-825 :: Loses Connection / Locks Up And Needs Reconfigure

Jul 30, 2010

I have a dir-825 connected to Cable modem and a dap-1360 connected I have both wireless and wired clients.If get a ip address conflict and the the dir-825 connection fails from the cable modem and nothing seams to restore that connection, i reboot both route and modem and make sure no client are on. The only way i can figure out how to restore the router is to reset and reinstall from factory state.I can recreate this on 2 different router "825" with factory and updated firmware.I have removed the wireless extender form the picture and this issue has stopped, it might be the extender of a client off the extender. But everything uses DHCP so I'm not sure why ip address conflicts could cause this issue.

View 2 Replies View Related

Cisco Firewall :: ASA 5505 Locks Up After 24 To 48 Hours?

Dec 4, 2011

We recently changed ISPs from Verizon T1 to Comcast fiber.
 
The only change made in the firewall was the outside IP address, gateway and mask.   No changes on the internal network or the interface.
 
After a power cycle everything is good from anywhere from 24-48 hours, then all traffic locks up.  The interrface shows as being up but no traffic can get through until another power cycle.

View 1 Replies View Related

Cisco Routers :: WRVS4400n Locks Up With A Repeater

May 8, 2012

I have tired different repeaters. First the WAP4410N. Especially in WDS mode it locks the router up. I have to restart it.Out of desperation I bought RE1000 that says it works with any "N" device. It also locked up after successfully configuring it.WRSV4400n v2

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved