Too many devices in our home including two playstations and 4 computers. I want to add a Linksys dual band E2500 to my existing WRT160N.
1. I will be able to hard wire the two together too.
2. Which Linksys router should I connect to my cable modem?
I just bought a linksys wireless n dual band router e2500 and i want to make my old wrt54g router as an access point. how do i do this and where to start?
View 11 Replies View RelatedI am using the E2500 v1.0 on TWC network (road runner) wit a VISTA upgraded to Windows 7 laptop.After few months the router is starting losing connection. I tried connecting my laptop directly to the twc modem and the connection is fine, while if I connect to the E2500 v1.0, through wired or wireless connections, I see that the connection is going back and forth.I tried resetting the modem and the router, upgrading the wireless router firmware, but nothing worked.
View 1 Replies View RelatedI have the new XBOX 360 black N wireless adapter and the Linksys E3000 dual band router as I want to upgrade the network range and speed to N. I set up a unique SSID and passphrase (WPA2) for both 2.4GHz and 5GHz bands. My XBOX could connect to the 2.4GHz band network and could connect to XBOX Live. But when I configured all the settings and tried to connect to the 5GHz band network, but no luck. My XBOX just said it failed to connect. I was sure that I did type in the SSID and passphrase correctly. I still cannot figure out what went wrong. I even suspected either the wireless adapter or the router malfunctioned.
View 9 Replies View RelatedI want to add my E2500 as a second wireless router to cover my entire house.I have a Motorola Surfboard SBG6580 cable modem (Time-Warner) at one end of the house.I added via powerline Ethernet connection a new E2500 wireless router at the other end of the house.The E2500 set-up with all defaults and has the same SSID and Password as the Surfboard cable modem.It seems to work OK, but I wonder about network confusion/interference.Do I have to configure the E2500 in some manner to allow seamless roaming of my wireless devices (iPad, Cell Phones, Netbook)?I had an RE1000 with just the Surfboard, but it did not quite do the trick, and does not like both routers connected at either end.
View 9 Replies View RelatedI have an existing wireless network using a Cisco/Linksys WRT400N wireless router (which in turn is connected to a cable internet provider). I need to extend my wireless coverage and so purchased a Cisco/Linksys E1000 to act as an additional access point. Purchased from BB, the local 'geek squad' rep instructed me to follow the users guide for the set up. After login into the admin service on my E1000, I followed the 'Advanced Routing' instructions and disabled the 'NAT' option and subsequently enabled the 'Dynamic Routing (RIP)' option. Everything worked like a charm to this point, but now I'm stuck. What steps do I need to follow to allow clients to log onto my wirelss network via the E1000 (secondary access point)? I've established WEP security keys on the WRT400N (primary access point) and want to use the same network security parameters on the E1000.
View 9 Replies View RelatedI have an E1000 router and recently moved to a basement apartment where the only internet access comes from a single Ethernet cable running out of a router upstairs. I can connect to that network (it is family) but ideally I would like to connect my router and create a second network so that I can connect my printer and other devices independently of the upstairs network.
View 2 Replies View Relatedhere is what I have:
A) Sonic Wall @ 192.168.1.215
B) Linksys Switch (WRW248G4P) @ 192.168.1.254
C) Linksys Router (WRT160N) @ 192.168.1.202 (Disabled DHCP Server)
D) Linksys Router (E2500) @ 192.168.1.203
E) Windows Server 2003 @ 192.168.1.200
F) There is also a Router @ 192.168.1.201 that runs DD-WRT that has an enabled DHCP Server.
It goes something like this
i) A - B --ETHERNET-- E
ii) A - B --ETHERNET-- C
iii) A - B --FIBER to another building, then ETHERNET -- D
Everything connects to the internet, but (D) on (iii) doesn't allow connection to the server (E). What can I do to make this work?
I had the store set up my EA3500 which is a dual band...home 1 and home 2. I can only see home 2 which is the smaller band width.
View 1 Replies View RelatedI have 4 devices in my network -
1. Cable surfboard modem
2. WRT160N Wireless Router - 192.168.1.1
3. Linksys 10/100 5-port wired switch
4. WRT160Nv3 - 192.168.1.2
My current setup is -
1. Modem to first router. (WAN PORT)
2. LAN Port from router to UPLINK port on switch
The switch is upstairs, the router is downstairs. The wifi from the router does not reach upstairs, so I have bought another WRT160Nv3.How do i add this to my setup? I've tried hooking the new router direct to a PC and configuring it so that it is NOT a DHCP server and changed the IP from 192.168.1.1 to 192.168.1.2 then connecting a LAN port from the switch to a LAN port on the new router and disconnecting the wired pc from the new router.
In the above setup NOTHING after the switch works. I cannot get internet while the switch is connected to the second router on any computer attatched to the switch. The wifi will not get internet either (from second router)
I changed the 5 GHZ SSID name using Cisco connect on my E3200 router as was expecting to see 2 available wireless networks on my laptop, but it seems that only the 2.4 GHZ is still broadcasting as it was before. When I connect to it with my laptop it shows it connecting with 802.11n, so I would think that my laptop would see the 5 GHz SSID if it was broadcasting. I am trying to take advantage of the dual band feature and connect the 5 GHZ to my blue ray player for real time video streaming.
View 9 Replies View RelatedI just setup my EA3500 router and both SSID's are the same.Is this ok or should I give them unique names?Since they are the same what are my products connecting to?If I do separate them, what item should connect to what network?
View 5 Replies View RelatedI have a Virgin Superhub at home which is capable of 2.4 OR 5GHz wireless. I have a mixture of 2.4 and 5 GHz tech at home so would like to use dual band. My wireless settings on my Superhub modem look like this.As you can see it has settings for 2.4 OR 5GHz and wireless modes of 54, 144 or 300Mbps.
What setting should I be using for my EA4500 to operate in dual band mode? I'm guessing I should put by Virgin Superhub modem in modem mode at 5GHz/300Mbps.I will besetting up seperate SSIDs for 2.4 and 5GHz bands.
Is the Linksys E4200 Dual Band Router compatible with DHCP and VPN?
View 1 Replies View RelatedMy ISP comes in via phone line to modem then to wireless router.I want to run 200' direct burial line to WAP so that I can access wireless internet at the far point. I have modem and wireless router. what do I need to do the create the distant wireless access?
View 2 Replies View RelatedMy wife has a home office with her office computer connected to our modem via a cisco router. Our home computer is connected via this router as well. I want to add a wireless router (netgear) so I can use my laptop anywhere in the house.
View 1 Replies View RelatedAdded a wireless router to our office here so that people with laptops could get on the net without having to physically plug in. Right now it is ok, but the router is acting as it's own DHCP server instead of our server here assigning out the IP's.
The main gripe I have is I can only login to the router through my phone and not through my computer. How can I achieve this. We have multiple offices that all connect through a VPN. I would like our sys admin to access the router at his location as well.
Do I just turn off DHCP on the router and thats it? The model is Netgear WNDR4500.
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP : Centurylink
I'm using a WDR3600 router, and I'm having difficulty with getting internet access on the 5 GHz band. Right now the router is broadcasting in both 2.4 and 5 GHz as two separate APs. The 2.4 GHz band works perfectly fine, but when I connect to the 5 GHz band my device is not assigned an IP address and cannot connect to the internet (or even the router configuration page). Unfortunately, I don't have another device capable of accessing the 5 GHz band, so I can't check to see if the computer is at fault, but both the computer and the router have worked together with no problems before, and this computer has done fine in accessing other 5 GHz bands.
I am trying to hook a second computer up to run off my belkin router?
View 1 Replies View RelatedMy wireless internet has been acting a bit weird lately. I use a linksys Dual band wireless-N USB adaptor (WUSB600N) to connect to my router, a 2wire 1000sw. I am on windows 7. Recently, the internet has been dropping and reconnecting the connection weirdly; it is apparent in Portal 2 Co-op mode; it says the connection has been lost to the server, and then within 4 seconds, re-joins the server. During that time, the little network icon (the 4 bars in the task bar) says "Identifying."
View 2 Replies View RelatedI have a working 3800 router which runs on bgp pretty well. Existing setup has 2 serial ports for the bgp and 1 gigabit port for the LAN.Now, i want to add another 3800 as a standby router making it clustered - ACTIVE/STANDBY via hsrp protocol.
1.) What are the implications in adding another 3800. Do i need to reconfigure the ip addresses on my serial? or just the LAN
2.) Are there any additional requirements like firmware versions etc?
I have 2 AE1000 USB adapters and according to the Linksys website these are wirelessN dual band selectable adapters. I finally hooked up my new e4200 dual band router and the ae1000 connect but I don't see anywhere on the screen in windows 7 ultimate 32bit that you can change the band?
View 1 Replies View RelatedI currently have a wired network which starts with a cable router downstairs which is a virgin media netgear box with firewall and DHCP turned on. I have a NAS server and a smart tv which run off ethernet connections to this router.then have a cable run upstairs to a TPlink gigabit switch which is connected to a PC and a printer (in my study). All this works just fine, no configuration needed.I have a TPlink wireless router, a TL-WR743ND. I want to use this to connect to the switch upstairs (not downstairs - my stone walls limit any wireless access point) to provide wireless network coverage for my house.So I figured I should configure it with a dynamic IP address (ie it gets it from the netgear DHCP), turn off the TPLink's DHCP and firewall, and then any wireless devices attached to the TPLink by wireless should have access to printer and NAS
View 8 Replies View RelatedRegion : UnitedStates
Model : TL-WDR4300
Hardware Version : Not Clear
Firmware Version :
ISP : Verizon DSL
My DSL connection comes into our house in the basement and the DSL modem came with a router included. I bought the WDR4300 for the higher speed wireless connections and the gigabit ports. I really don't need the "router" functionality. I would like to put the WDR4300 on the second floor to give (hopefully) the broadest wireless range. However, I would like all my PCs (including those wirelessly connected) to be on the same sub-net. Is there a way to configure the WDR4300 so it acts like a switch rather than a router?
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : fullrate.dk
My ISP has provided me a router: Zyxel P-2601HN which has an ideal WLAN transfer rate of 150 mbps. I live in a concrete 2 story house so signals are weak at best on the other floor - therefore, I Have bought the TL-WDR4300 as an extension for the latter floor. I have connected the routers from LAN to LAN and the Zyxel has 192.168.1.1 on LAN and the TL-WDR4300 had 192.168.0.1 as out set. I have changed this to 192.168.1.2 and all the setup (disabled DHCP + other) seems to work alright. BUT i can not log into the TL-WDR4300 !! Not with http://192.168.1.2 and not with [URL]. What I can do to get into the setup of TL-WDR4300. I know I can alays backup the setting and reset the router and load the setting again, make alterations, saving .....but it kind of drastic !Can the two radios SSID names (2,4 MHz and 5 MHz) be the same name as the SSID name on the Zyxel P-2601HN ? What are the implications ?
I confused ,with which modem to purchase to set up my n600 wireless dual band gigabit router wndr3700, i'm on boardband with no modem
View 1 Replies View RelatedI got a NetGear DGND3300 Wireless Router Modem 3300 Dual Band from eBay only to find it will only work in USA.
View 7 Replies View RelatedRegion : Brazil
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.6 Build 110923 Rel. 53137n
ISP :
I'm trying to use TL-WR2543ND to connect 50 tablets to my wireless network, but as it establish around 20 connections, no other tablet is able to connect to it.
I've made no custom configuration to the wireless settings of the router. Is there anything a need to do to get the 50 connections?
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 1
ISP : cox.net
I have downloaded the file TL-wdr3600_v1_130129.zip. Extracted the file to a temp folder. Thje file is a bin file which is a bin image wdr3600v1_en_3_13_26_up(1301).bin. I do not see any flash file to load this to the router.
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : Teksavvy
how can I see who connected to my router?
ive got 2 laptops on my wireless network and have just bought a pc. it dosnt seem to be finding my connection so i cannot get it onto my wireless network?
View 1 Replies View RelatedRegion : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : Latest
ISP :
The UDP connections are being blocked when I use my VPN. I can connect for a while but soon after a while, the connection doesn't work. I can't even access the router page.
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.17 Build 120426 Rel.29216n
ISP : Bell Canada
Just had my line upgraded to 50mbit down, and 10mbit up. Whenever the router is between the PC and the modem, my speeds drop to 30mbit. If i plug directly into the modem, I get the full 50Mbit. Upload speeds are always 10mbit.I've tried power cycling devices, and even replaced all cables with cat6 (which I know isn't the issue, but i'm just trying to eliminate everything)