Linksys Wireless Router :: Configuring EA2700 As Second-level Router?
Jan 28, 2013
I need to front-end my ISP's router with another, giving me a DMZ. I have bought an EA2700 for this but I can't find how to configure it.
I plan to have the DMZ network as 10.1.2.0/24, with the ISP's router at 10.1.2.254 and the EA2700's "upstream" connection as 10.1.2.1. The internal network (where most of the clients reside) will then be 10.1.1.0/24, with the EA2700 itself at 10.1.1.254 and a DHCP range 10.1.1.100 upwards.
On the basic setup screen I've set the Internet connection type to fixed IP, 10.1.2.1; I've set its default gateway and DNS1 as the ISP's router at 10.1.2.254. Then further down in network setup I've entered the *internal* address 10.1.1.254 and set the DHCP range and netmask appropriately. I'm getting the error message "The IPv4 address and gateway are not in the same subnet mask". But the only gateway I've entered is the one by which the *EA2700* knows how to route upstream traffic, viz the ISP's router at 10.1.2.254. Or am I misunderstanding?
More fundamentally, can the EA2700 be configured in this way?
I recently bought an EA2700 in hopes that it will make my connection faster, stronger signal and stable. However, this is not the case. The connections keeps dropping and the range is the same as my Verizon-FiOS router. Anyway, I'm hoping that a fix be distributed to address this issue. I can't return my router to the vendor anymore.
Now, since I have two routers, I want to be able to leverage EA2700's dual-band feature and the Guest-access feature but I can't make this as a main router since my FiOS router should still be able to supply IP addresses to my cable boxes, thus, I can't configure it as a Bridge. I'm thinking if I just split the IP distribution as follows:
If I update my firmware on my EA2700 router to be able to use the Cloud, will I loose the ability to connect to my router on 192.168.1.1 ? If this is so, why couldn't linksys let you use both Cloud and 192.168.1.1 in their latest firmware?
i got an ea2700 and i cant get the external to work internally which i need for server tests now this has worked before on every other router i had without any editing done but this one doest allow that so what can i do to make it work with this router?
I recently purchased an EA2700 to replace an old Belkin. I ran the set up CD and I am unable to establish an internet connection. I am able to connect to the router (both wired and wireless), ccess the settings, etc but cant reach the net. I've tried turning off the firewall, flushing the DNS, disabledthe IPv6. Did all the basic steps, resett the modem/router, etc...nothing. i hook the Belkin up and it connects just fine
I have EA2700 Router which support to be a dual-band wireless router and I am trying to connect to my router using 5 Ghz band with AE2500 Dual-Band Wireless-N USB Adapter, I am only seeing 2.4 Ghz wireless band plus even if I manually enter my 5 Ghz SSID my network adapter still wouldn't work on 5 Ghz band. Is there any specific set up in order get 5 Ghz band to work?
My first issue with this device is when I try to untick NAT to disable it I lose my internet connection. This also disables access to router's address 192.168.1.1 forcing me to reset the device and set it up all over again. Why is this happening? I tried this at least five times with the same result. Second question I have is if the DHCP reservation is the right option if I want to forward ports for certain applications like Vuze? When the DHCP reservation window opens I see all my wireless devices in the list (laptop, phone) but not the main computer which is connected through ethernet port. But that is yet another problem.
I've got a cable modem, connection is set to Automatic DHCP and I all want is to disable all firewalls, NAT and other unnecessary protection that's slowing my internet speed, set up MAC address filtering, port forwarding and close this terrible software so I never have to see it or think about it ever again.
i have a EA2700 router and I'm connectied wirelessly to my PS3. If i am not hosting a game i will be lagging all over the place yet it says i have full connection to majority of games that i connect to. i paid 115 dollars for this router and am very dissapointed that its doing this. Also no there is no way for me to connect wired to the router it is to far away. Also i tried bringing my ps3 to my friends house and played on his wireless connection and it worked perfectly so its deffinetly my router.
EA2700v1 WPS-PIN using 5GHz does not work. This router includes WPS header in its 5GHz beacon and probe response but the router removes the WPS header from them once WPS-PIN starts. There is no problem with WPS-PIN using 2.4GHz.
I am not able to access the web interface of the router.No, i am not using cisco cloud or smartlink .. yes, it has the latest firmware (Ver.1.0.14.129982).Yes, I might be able to get to it if i shut down the router and turn it on again a few minutes later, but the problem is.. why? why do i have to interrupt connections and not have internet to log into the admin web interface of this device? Is there a known problem with it that makes the webservice go down?.. or to take extremely long to respond and thus the browser to quit on it throwing an error?
Im not able to conect to the internet threw my router, but i am able to with my modem. i dont want to pay for a new one and Cisco wants me to pay $30 for phone support.
My new EA 2700 disconnects from the internet if the desktop is idle for more than 30 minutes. needs to be unplugged for a few minutes then it will reconnect. This is an unacceptable situation and this thing will be tossed if it cannot be fixed. Can this be reset so it won't disconnect? or do I need to replace it with a product from another company?
I have an Cisco EA2700 router and a Motorola SB6121 modem. If I'm connected to the router wirelessly or through any of the lan ports, I can't visit the modem's diagnostics page at 192.168.100.1. If I connect directly to the modem, it works fine. Also I cannot ping the modem through the router, just get a timeout. My ISP is Comcast.
I have tried all the speed test sites and tried downloads with and without my EA2700. Every test shows about half the perfomance when connected through the router. My speed tests at speedtest.net with a direct connection are in the 21-26Mbps range, the same tests run about a minute later through the EA2700 fall in the 10-12Mbps range with spikes up to 17Mbps.I've reset the router and modem.I've gone back to the 1.0.14.129982 Firmware (which it's currently on)I've set the MTU everywhere from 1400 to 1500 (literally EVERY setting for at least a couple of hours) it is 1492 currently. None of these have worked. In addition, when a large stream starts, such as a Steam download, I will lose ALL connectivity. Going in to Network and Sharing and clicking to connect to the internet restores the connection, no need to reset any hardware (which is odd in itself). I have had MANY routers over the years and I've all but exhausted support with service provider as the connection is solid if I eliminate the router.Main machine is a Windows 7 Home edition Total of 5 machines, 3 of which see regular use All machines go through a Trendnet 16 port switch and performance is the same direct or through the switch I m on Brighthouse in Central Florida and have all but exhausted their support.
I have a linksys EA 2700 with the latest smart wifi firmware. However, the "Release and renew" of the IPv4 internet ip is greyed out. Only IPv6 is enabled.
went through setup twice, double checked connections, bought new ethernet cable from router to computer, still not connecting. However when i go from my modem to computer i get connected. could i have a faulty router. the router is new from walmart the ea2700.
Every time after the router (Linksys EA2700) is powered off and restarted, there is no interent access available. The router configuration status reports an Internet Address of 0.0.0.0 and all the devices at home are left with a wifi without Internet access. I have to unplug the WAN from the router and plug it in again while it is turned on to restore internet access (and a normal Internet Address is seen from the status page). The WAN works fine with the routers I had previously. I wonder if I have to perform this every time I power on the router. I have tried resetting the router and reinstalling Cisco Connect but that didn't work.
I have a EA2700 and will try to reserve an IP address to a PC, but getting up that address is invalid.I already have two reservations, which is 192.168.10.10 and .... 50, I try to reserve ...... 20 but am getting alert that this then is "Invaldi IP".
I have an EA2700 (fimware "classic" 1.0.14.129982) that used to work perfectly fine with a Comcast cable modem. I just recently switched to Charter with an Arris TM902 modem and that's where the problems started. The cable modem will not recognize my router. I have to plug in a computer into the cable model when it starts up. Then I need to clone the MAC address and restart the router (after disconnecting the computer). Why isn't the cable modem recognizing the router when I restart it? I guess this could work if it would be a one time thing but I had to power-cycle the modem and it stopped recognizing the router even with the cloned MAC address. So I had to do the whole spiel again.
Is there any way to make this work easier? Should I update my router's firmware to the "smart" one?
I just bought linksys EA2700 to replace my U.S Robotics .. but when i try to connect it like the old router , the internet lights won't turn on, is it because i have to use a modem then use ethernet cable ? can't i just use ADSL cable directly to the router like robotics router ? when i try to configure it manually , i change the internet type to PPoE protocol but i can't find VCI/VPI so where are they ?
I have a Cisco outer EA2700 connected using a Lan cable, Lan cable works fine as I connected it directly to my PC, I am unable to access wifi network connection, I am able to search the router and also able to cnnect to the router, But wireless connection shows limited or no connectivity, and unable to access any websites. It was working fine till yesterday, I tried rebootng ad also unplug and replug the network cable also reset the router but does not work
I have a nest in the house and upgraded my router because nest is very picky with what routers it works with..something to do with power save mode and NAT settings Read here.well the linksys was working just fine with the nest until I upgraded the firmware to the smart wifi thing...it's a EA2700 btw.
My new router has started to disconnect for a second or so from the internet then reconnect. I have been unable to see the issue and changing the frequency was unsuccessful. This has also been happening when connecting both wired and wirelessly
I have had my EA2700 for about 6 months now. Have had no problems until about a month ago. One night I could not get the router to connect to the internet. First thoughts were that the cable connection had gone down. When I finally started to trouble shoot I was able to confirm the cable connection is fine by connecting to the modem directly.
Out of the modem I am getting 14+ Mbps. (I only Pay for 10 So a plus there)
I could not get the router to connect to the internet. I ended up resetting the router and reconfiguring it. Ever since then I have been getting really unstable connection to the internet.
When I connect directly to the modem (cabled) I am getting a nice steady connection . When I add the router and hardware in I get a good connection only a Mbps or 2 drop off and a pretty steady connection. Then when I connect over WIFI I get a much larger drop off depending on if the device is a 2.4 or a 5
The connection is extremely unstable. The curve on the graph {URL} is very peaky and has extreme highs and lows. This is multiplied when running on the GHz (as my laptop runs on). My Iphone running on GHz. I can pull down 9 Mbps but the curve is still up and down. Iphone on GHz I barely get Mbps and it is extremely choppy on the graph.
I am able to back this up with my I PAD. I can only confirm the 2.4 number with the laptop as it does not have GHz radio in it. So every thing that us running on the 2.4 is getting poor connections.
I also suspect that the through put on the wired side is poor as well. I am unable to prove it as every test I run shows a good connection but netflix has been locking up and I have to restart what ever I am watching 2 to even 10 times a show. I need to do more testing to be sure the network or the devices are to blame.
I have a domain name which I register to my WAN address so I can do service hosting from my home network. I recently switched out my WRT54G running DDWRT with an EA2700. I set up my port forwards and static dhcp assignments and they are working from outside my network, but when I try any network operation involving my WAN address from my LAN machines, the connections just timeout.
I read in some posts that "you cannot do this" and "you have to test from a remote internet machine". Well, this WORKED with DDWRT, so it's not like it's impossible to make a router that does this. Why can't I do this with the EA2700? Is there some magic setting that will let this work??
The whole point of using a domain name is that I can access my services ANYWHERE using the convenient "name" thing.. genius, right? Except when I bring my laptop home and suddenly my domain goes non-responsive.
I have a cisco EA2700. How to clear the connected devices list?I want to use the parental controls, but when I look at the list it shows every device that was ever connected to my wireless.
I have an EA2700 which I am trying to rollback to the older interface, however it errors out every time I try to install the firmware.All I ever get is this message: Unexpected Error The firmware update did not complete successfully. Please try again later.We've encountered an unexpected error. If the issue continues, please visit our Technical Support site.I've reset the router multiple times, powered it off overnight, re-downloaded the file multiple times, and am still unable to successfully rollback. Sometimes it even errors out when I try to set the password on the router itself and I have to reset it again before I can use the interface.
I have an EA 2700 installed using a wired network. It is just one desktop computer and a VOIP box shared by my internet connection. I am quite new at wireless connectivity.I would like to add wireless devices, specifically a phone and a laptop, but I do not want ANY of the wireless devices to be able to access and make changes to the ROUTER or any other computers on the network. I do need to keep the network secure.How do I set the router and/or devices up to accomplish this?
This is about to cause me to buy another router. This will be the 4th clean install that I have had to do. If my power, or my internet goes down, a regular proper reboot / or reset, will not get my ea2700 back online. It takes uninstalling & deletion of the stored Application Data files.
