Linksys Wireless Router :: Connecting E3000 To DIRECTV DVR?
Sep 12, 2011
I want to setup a hardwired connection between my Linksys E3000 router and a DIRECTV DVR. I have the most recent firmware on my router. I have checked the ethernet cable and it is good. The lights on the ethernet port on the DVR light up when I have the DRV and router connecter. The DVR gives me an error message when I try to connect. Some other posts have suggest setting a static IP on the DIRECTV DVR using the following settings:
IP Address : 192.168.1.10
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
DNS : 192.168.1.1
I tried this and still get an error message so I am going to call DIRECTV. Before I do call I would like to know if these are the correct settings for a Static IP?
I had a little one port wireless switch that I just upgraded to the SE2500. The problem is my home audio reciever and squeezebox aren't connecting to my network now that I upgraded. The E3000 isn't seeing the SE2500 at all, nor is it seeing the devices connected to it. Everything else that's wirelessly connecting to the E3000 is connecting just fine (Tablet, Laptop, Desktop, etc.) but anything connected via wired to the SE2500 is not showing up whatsoever.
I have 3 computers in total: 2 desktops and 1 laptop.
1. My primary PC is connected physically to my router.
2. My (downstairs) laptop is connected to the wireless.
3. My other PC connects to the wireless network via USB wireless adapter.
I was having issues getting #3 connected to the wireless network. I used the Wi-Fi Protected Setup™ PIN number provided to me by the Linksys Wireless Manager to no avail. The E3000 router and #3 could never find each other.After calling support, it turns out that more often than not, "other" wirless management software (in my case Linksys Wireless Manager that came with the USB device) was interfering with my Windows XP Wireless Manager.Rule of thumb: Always let your native operating system manage the wirless networks that are available to it. It does a far better job and is 10x more reliable than software provided by 3rd party vendors.Specific to my case: Windows XP, I had to enable the Windows Wireless Manager and uninstall the Linksys Wireless Manager Software. Here it is...Enabling Windows Wireless Manager These directions are for Windows XP:
1) From the Windows Start menu, click Control Panel.
2) Click Network and Internet Connections.
3) Click Network Connections.
4) Right-click the icon for your "wireless network connection", then click Properties.
5) At the top of the window, click the Wireless Networks tab.
If the "Wireless Networks" tab does not appear between the "General" and "Advanced" tabs, you are not on/in the wireless network connection settings:a) click cancelb) Right-click the icon for your wireless connection and choose "Enable". c) return to step 4 6) Check the checkbox next to "Use Windows to configure my wireless network settings".
These directions are for Windows Vista:
1) Go to the Windows start menu and then the control panel.
2) Open Network and Sharing Center.
3) Click Manage Network Connections (from the left side menu).
4) Right click on the network adapter 'Wireless Network Connection' and choose "Properties" and click "Continue".
5) At the top of the window, click the "Wireless Networks" tab.
If the "Wireless Networks" tab does not appear between the "General" and "Advanced" tabs: a) click cancel b) Right-click the icon for your wireless connection and choose "Enable". c) Return to step 4
6) Check the checkbox next to "Use Windows to configure my wireless network settings".
I get a great wired connection but when I try for wireless the Samsung says I have a great connection, except when I try to use the Apps from the Blu Ray it tells me, No Internect Conncetion. Samusung support tells me I need to "open the ports" on my E3000 and make the Blu Ray a priority...I don't know how to do that.
I purchased a refurbed? router on the internet, not supported any longer by Cisco Chat. I have a wireless internet: WiMax thru Clear wireless. I have a Linksys voip box coming off it for my phones. I installed the disk that came with the router, followed the directions, and got a message that Internet could not be found. Went to the live chat and followed some advice that did not work, conflict with voip? bypassed the voip and ran a cable from the wireless modem to my E3000.
I have Verizon IP with a Westell 6100 Modem and a Linksys E2500 Adv Dual Band N Router, that seems to be having problem since hooking up our DirectV Cinema on Demand to it. It constantly drops the internet connection to BOTH the hard wired and wireless internet . The internet drops and returns every few seconds it makes connecting impossible. Any one have Manual connection instructions for this set up?
I I use a Linksys E3000 router. Sometimes when I look at the network map I see a device called "Unknown." It appears as though the two notebooks sometime are going through this device to access the Linksys E3000. (I've checked when both notebooks are on and I can determine what devices are connecting directly to the router and what devices are going through this unknown device.) Is there any way to determine what this unknown device is?
I have the Linksys E3000 High Performance Wireless N-Router and I am having trouble connecting it to my PS3. The PS3 recoginizes the router and gets as far as trying to connect and then it tells me that the internet connection has failed and that the connection has timed out, even though it only tries to connect for a couple of seconds, therefore I dont see how it would have time to time out.
I have a linksys wrt54g ethernet wired to my router. I got a wap54g and don't know a thing about either. I hooked up the wrt54g years ago with linksys assistance. I thought I could just hook up a wap54g with ethernet to the directv dvr and the two would talk.
Linksys WRVS4400N won’t connect with my DirecTV DVR. I spoke with the DirecTV tech folks extensively about attempting this connection but I can’t make it happen and they are stating it is an issue with the router even though I have Wi-Fi throughout my house. I changed the password and deactivated all of the possible firewalls and still no connection.
I have a Linksys E3000 router set as Lan-Lan 192.168.0.2 hosting my internal LAN connected to a motorola Surfboard (Brighthouse) internet Wireless/Wired access point 192.168.0.1.I have a Web server hosting a site connected direct to the surfboard (works fine) . The FTP "site" on the E3000 can be seen by all pcs on the internal LAN. However, it can NOT be seen from the internet (Android with FTP client being used for test device)
Primary Access point 192.168.0.1 DCHP server with reserved IP addresses for server and PC's and smartphones Port Forwarding Set for Server at 0.004 : 80 Port Forwarding Set for E3000 at 0.002 :21
Secondary (E3000) router 192.168.0.2 DCHP server is disabled Port Forwarding is Not being used connected to primary router LAN port 1 by LAN port 1 on E3000
All pc's can access the Internet when connected to the E3000 via cable or wireless?All pc's can access the FTP server on E3000 via cable or wireless as a LAN location (connected to either router)?How can I get the FTP to be seen from the internet ?
I recently bought a Cisco e3000 router. I updated the firmware but I am still only getting 1.33 Mbps at most. The only things plugged into it is my PC and my xbox. I bought the router so i could get a better connection on my xbox so netflix wont stop playback.
Tried numerous times but no Internet connection between Directv hr23-700 and Netgear DSL 7550 modem/router. Is connected to home network, but no Internet.
I have an e3000 that cannot obtain an address from the ISP. I can get an address on the computer and an old router by directly connecting the cable to the computer or the router. I can also daisy-chain the e3000 to the old router, and I can get an address on the e3000 from the old router. I have hard reset the e3000, changed firmware from the Linksys to TomatoUSB and back to Linksys, and I still can't get it to work. It worked fine on Saturday until a bolt of lightning hit close to the house. Since then, I cannot get the e3000 to connect to the ISP.
I had a failed Tomato upgrade and now Connect Setup can't see router to revert back to original. I get message 82BD0101 or computer not connected to router. Also the http://192.168.1.1 trick won't work. Is there any way to restore besides 30/30/30?
I would like to override the DNS servers provided by DHCP via my ISP. The other settings I would like to preserve (like my assigned IP).How to achieve this with E3000 ?
It seems like after a certain amount of time, maybe a few days... my E3000 gets slowww.. I'm talking dog slow. And it's not just the internet, I have a media server connected to it, and usually when I put something on it, the transfer rate is about 3.5MB/s (not bits, bytes). But everything is slow, I top out at speed of maybe 1/6 normal on the internet as well.
We have a wireless internet service. Not satellite. We basically have an antenna on our house that picks up the signal from a tower a mile or two away. I used the e3000 router when we lived in town with broadband internet and it worked fine. I can't get it to keep a hold of a signal. I can connect to the router from the computers but the router drops the signal from the tower. I have an old router that the wireless company was kind enough to lend me that works , but the signal is weak and it could die at any moment... I"m at my wits end.. I have an expensive piece of equipment that wont hold the signal. I have updated the firmware and the Cisco connect software..
Has anyone tested QoS on the new E3000? Whenever I add an application (e.g. Voice Device) and set priority to Medium or High, my upstream bandwidth for everything else is immediately cut significantly, even when I'm not using the priority application.
For example, with QoS disabled, I can consistently get 10Mb upstream (speedtest.comcast.net). As soon as I enable QoS, upstream is capped to exactly 2Mb! On my old router, there was an option to set the total upstream bandwidth -- but on the E3000 there is no such option that I can find.
just bought an e3000 and want to use it with wireless internet- usb modem. when setting up it wouldnt go any further than the 'searching for connection' page as it couldnt detect a connection in the 'internet' lan (wan?) port.can i set it up to accept the wireless usb modem?
I just bought an E3000 about 30 hours ago and just unrealistically my router now doesn't want to give me any WiFi at all. I tried reset button, tried re plugin all of my system as well as pressing for short and long period the middle button that indicates WiFi is accessible. I already bought 3 linksys routers.
Looking at upgrading my router to an e3000 however I've got a couple of questions. I might come across as a bit thick with this one but I have read that you need a modem to make the router work, I can't get my head around this as I've not come across this before. I always thought the router was the modem!! I've also heard that the E3000 only works with cable ISP and not ADSL, is that true?
I have FiOS and their supplied wireless router Actiontec #MI424WR. I have home theater equipment that uses the newer N signal so I purchased a Linksys E3000 Wireless-N Router. I have one of the LAN outputs on the Actiontec feeding the Linksys input and Wi-Fi turned off on the Actiontec. This is working good for my wireless home theater equipment but I am having problems with my wired speed. It has gone from averaging anywhere from 20 to 30 mbps on numerous test sites when plugged into the Actiontec to averaging around 10 mbps when plugged into the Linksys.
1) Is my wireless N speed going to top out at 10mbps or less since that is all the router is showing on wired? Shouldn�t N be broadcasting a faster speed if given the ability?
2) I have my computer currently plugged directly into the Linksys verses the Actiontec. This makes it easier to program the Linksys router. Since I am no longer using the wireless part of the Actiontec there really is no need to be plugged into it. Is there anything I can do get the speed higher on the Linksys, a setting I can change? Will I have to plug the computer back into the Actiontec to get the higher speed and then move it every time I may need to make a change to the Linksys?
Want to switch to dualband E3000 from older, working fine except needs resetting often. What steps do I need to take? I do not have E3000 setup disk. I fear that I will go down a path that makes both of the routers unusable, at least down many hours.
I've been searching how to make my E3000 use the DHCP and IP address on my primary router so I can share printers and computers on same gateway IP. I tried turning off DHCP on E3000, but not sure how to tell it to use the DHCP from the source "INTERNET"
shows connection to cable modem, shows IP lease, able to renew and release lease. shows all DCHP clients, but does not allow internet to get through. tried cloning old routers MAC, no dice.
A retailer (Best Buy's Geek Squad) made adjustments to my Linksys E3000 router when I bought a Sony Media Player from them a number of months ago. It was the first wireless device integrated into my wired LAN network (three computers).
In attempting to set up a GUEST connection, I pulled up Cisco Connect which I originally used to set up my network. The BB Geek didn't use a key and followed a different procedure unknown to me.
As I face the Cisco Connect screen now, it tells me "Can't access your router settings. The router password has been changed." Then in the "Router password" block, it gives the original password I assigned.
I had written another name I thought was associated with the changes made by the BB Geek so I copied the password there now, inserted the new PW, and clicked Next. I was then asked if I wanted to proceed with the change ... but the change it was proposing was the exact PW I just copied. Confused, I cancelled the operation.
