Linksys WRVS4400N won’t connect with my DirecTV DVR. I spoke with the DirecTV tech folks extensively about attempting this connection but I can’t make it happen and they are stating it is an issue with the router even though I have Wi-Fi throughout my house. I changed the password and deactivated all of the possible firewalls and still no connection.
View 3 RepliesI have a linksys wrt54g ethernet wired to my router. I got a wap54g and don't know a thing about either. I hooked up the wrt54g years ago with linksys assistance. I thought I could just hook up a wap54g with ethernet to the directv dvr and the two would talk.
View 2 Replies View RelatedCannot get DirecTV HD-DVR to connect to DIR-655 wired. Any way to get Direct TV to connect?
View 1 Replies View RelatedThis is a new device, just initially installed about a week ago. I updated to the latest firmware. We have iphones, ipads, and Samsung Galaxy smartphones all trying to connect to this WAP at this office, but cannot seem to connect. If I power cycle the WAP, we can connect for about 5 min, then it loses it and cannot connect again. I have strong signal, device says "connecting" then immediately "disconnected"... does this on loop forever.WPA/WPA2 PSK.I don't know what to do. About to go buy an Apple WAP.
View 3 Replies View Relatedafter being able to see the cctv on the local network and remotely, we are simply not able to connect remotely again. This happens several hours after leaving site. The clients ip seems to be unchanged from last time, and we do get a " resource online but isn't responding to connections attempts" message from IE8. The ports have never actually shown as open from online port verification sites, but again, we were able to see the cams via 3g and from another town just fine.And we can see them on the locally. I'm convinced it has to be some setting on the router relevant to port forwarding.
View 3 Replies View RelatedJust purchased a WRVS4400N and for about 6 hours last night tried to get it to work and connect to my cable modem...no success. Is there a setting im am overlooking? I have enough network experience to be dangerous but am not an expert. All other routers i have had in the past have been plug & play mostly. This one is making me want to throw it thru the window. When i plug it in to the modem it dosent even give me a link light that its connected, much less communicate with it.
System Details:
- WRVS4400N Connecting to a Arris TM722 cable eMTA modem
- all cables have been verified (100 times by now)
What i have tried:
- Cloning my PC MAC address
- Pluged in my old router (Linksys E3000) and it connects instantly (Same cables)
- Same as above with PC
- Changed a million settings in the router (to much to list at this point)
Quick VPN and have not had any success connecting with our router. Below is my components info. Cisco router: WRVS4400N, Firmware V2.0.0.7. The router is behind a Comcast SMC business gateway modem Remote computer: Window 7 Ultimate 64 bit
I downloaded the Quick VPN client 1.4.2.1, and installed the client successfully but cannot connect using the VPN Client Account that I had set up in the router. Below are several questions that I hope to understand.
1) Do I need to configure specific ports for VPN in the Comcast gateway firewall?
2) What IP address do I put in the Quick VPN client profile when I connect remotely? The WRVS4400N modem shows 2 IP addresses in the Status:
DNS1: 68.xx.xx.176
DNS2: 68.xx.xx.132
Are these the IP that go into the "Server Address" on the Quick VPN client profile? and which one of the two? or do I use the static WAN IP address provided by my Comcast account?
3) In the Quick VPN client window, what is the "Use Remote DNS Server" mean?
4) Do I need to create a client certificate from the WRVS4400N for the client
5) Is there any setup needed for the remote firewall (if the client is behind a home wireless router and modem, for example)?
Tried numerous times but no Internet connection between Directv hr23-700 and Netgear DSL 7550 modem/router. Is connected to home network, but no Internet.
View 1 Replies View RelatedI have an WRVS4400N configured as a WAN and Wireless router and can connect clients (PC's and laptops) wirelessly thru out the office. The clients that are farther away (10-15 meters and on another floor) connect at a very slow rate i.e. less than 10MBps. I have a WAP4410N configured as a repeater. Immediately after powering up it will allow connections to the 4400 and clients work fine for a 1-2 minutes, then the connections drop and I can no longer connect through the 4410. Nor can I ping the 4410 through the 4400 although right after the pwr cycle I am able to ping the 4410. After another pwr cycle the 4410 is available for another short period.I have attached some info on the configuration of the units and I also have the configuration files available.
View 4 Replies View RelatedI want to setup a hardwired connection between my Linksys E3000 router and a DIRECTV DVR. I have the most recent firmware on my router. I have checked the ethernet cable and it is good. The lights on the ethernet port on the DVR light up when I have the DRV and router connecter. The DVR gives me an error message when I try to connect. Some other posts have suggest setting a static IP on the DIRECTV DVR using the following settings:
IP Address : 192.168.1.10
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
DNS : 192.168.1.1
I tried this and still get an error message so I am going to call DIRECTV. Before I do call I would like to know if these are the correct settings for a Static IP?
I have Verizon IP with a Westell 6100 Modem and a Linksys E2500 Adv Dual Band N Router, that seems to be having problem since hooking up our DirectV Cinema on Demand to it. It constantly drops the internet connection to BOTH the hard wired and wireless internet . The internet drops and returns every few seconds it makes connecting impossible. Any one have Manual connection instructions for this set up?
View 1 Replies View RelatedI can't connect my DirecTV DVR to my WRT54GS router. I am using a new cat6 ethernet cable to the router.
View 5 Replies View RelatedRecently I upgraded my Internet speed at the ISP from 10Mbps to 25Mbps and the problem is that I am measuring only 15Mbps using [URL]On the day when the tech came out to install the new DSL modem, he noticed the difference and as part of troubleshooting, he bypassed the Linksys router and voila the net speed measured 25Mbps using speedtest.net.So, why my Linksys WRVS4400N V1.1.13 acts like a bottleneck in this case? I didn't have this problem at the speed of 10Mbps. The upload speed is OK, it is 5Mbs with or without the DSL modem.
View 2 Replies View RelatedI cant get the WRVS4400N to connect to my cable modem. The WAN link light isnt even lighting up. Im wondering if this unit is bad out of the box. Is there a setting im missing to get them to talk to one another. This is no mention in any of the manuals.
Connections: - The "Internet" port on the WRVS4400N to the "Network" port on my cable modem (No link light)
Here is what i have verified at this point: - My old router connects instantly to the modem when plugged in (Same cable) - When i plug my laptop into the WAN port on the WRVS4400N i get a link light. When i plug the modem into the WAN port...nothing.
I just purchased a Toshiba Thrive tablet and I can't get it to connect to my wireless router. My router (WRVS4400N) works flawlessly with my laptop and desktop. I have spoken to a Cisco tech rep and they assured me that there is not a compatibility problem with the WPA-Personal setting I am using. When I speak to a Toshiba tech they tell me I have a router conflict. To verify this I went to my local Starbucks and low and behold it logged right on with no problem (The Starbucks system was not a protected system). This confirms to me that there is a conflict between the router and the tablet.
View 1 Replies View RelatedAs a temp work around I have two SSID now, one for everything else running WPA2 and one for xbox running WPA. The xbox seems to not like the router on WPA2 and though this would make one think, oh its your xbox, thats not always the case with devices. Some just may happen to want to use a feature the device doesn't support correctly and other devices are able to work around it while ones not so I cant for sure blame on xbox.
View 1 Replies View RelatedRight out of the box, the WRVS4400N [firmware v2.0.1.3] I just purchased says the WAN interface is DOWN; and it simply will not obtain an IP address from the Arris TM602G cable modem it is attached to. Internet still runs great on the old WRT54G. Is this WRVS4400 DOA? Or is there some arcane setting the quickstart guide overlooks? OR?
View 2 Replies View RelatedI'll just use the 4400n to provide DHCP to my two VLANs and then a new problem cropped up. I am unable to add a default route to the 4400n's DHCP server. It uses the 4400n's vlan IP as the default route. What I'm trying to ultimately achieve is to configure the 4400n as an access point for our "private" network on vlan1 and also "guest" access to the internet on vlan2.
View 12 Replies View RelatedI'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems. I have tried just about everything I can think of but have not been able to get this to work. setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?
Ive setup a few WRVS4400N over the past 6 months, and have been receiving the below message from some of them every couple of hours.What does the message indicate?
View 1 Replies View RelatedI have successfully got QuickVPN working from Windows 7 64bit into my WRVS4400n. The router is sat behind another router/modem (Belkin) as the UK uses PPPoA and the WRVS4400n doesn't.So I set up DMZ and changed the DHCP to always allocate 10.x.x.2 on the Belkin which is the WAN side for the WRVS4400n as it is the only thing attached.I have now noticed, and I'm not sure whether it was the case before, that the DNS that the WRVS4400 is showing is the LAN address for the Belkin Modem/Router (10.x.x.1), not 192.x.x.1 for the WRVS4400n itself. I assumed setting the Static DNS 1 on the WRVS4400n would do it, but it didn't?When I connect into the network with QuickVPN, the computer names do not show even though I have selected the option in QuickVPN?
View 1 Replies View RelatedOur business was looking at purchasing one of these Cisco routers and were curious if it supported WPA2 EAP-TLS?
View 2 Replies View RelatedI have 2 WRVS4400N's available to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.
View 1 Replies View RelatedRecently installed a WRVS4400N router on my home network. Prior to that I was using the wireless built into my FIOS router. I wanted something more secure so I went with the WRVS4400N. I turned off the FIOS wireless and am only using the cisco wireless.
Im having intermittent issues with the wireless. I have many things hooked up to my wireless including a HP printer and a Sonos system. Most of the time if I just open my ipad I cannot see anything else on my network including the printer. If I try to see the Sonos system can cannot, sometimes I can open the app on my iphone and then I can see it.
Sometimes I can see the printer and sometimes I cant. Sometimes when I do see it and then print to it, it will be gone before it even prints.
I don’t seem to have any issues thru the LAN connections.
Also, ive noticed that the wifi is much slower than the old FIOS box.
FYI, when I remove the cisco and fire back up the FIOS wifi I don’t have any problems at all at any time. And its much faster.
I have tried channel 6, 11 and auto. Also turned off IPC and still no change.
I have a gateway to gateway vpn (home-office) working fine for almost an year btw 2 wrvs4400n routers, This morning, the VPN tunnel was down. I clicked "Connect" from the web based interface, but it does not reconnect.
I tried setting up a new tunnel using the VPN setup wizard, but it says it can't connect to the remote router. Which is strange, since I can ping there normally.
I'm having a heck of a time connecting the WRVS4400N VPN to another WRVS4400N VPN. both of the routers have the current firmware version V2.0.2.1: Router 1 is below, and router 2 has the matching configuration with as it should be the local group being that routers local information and the remote crew set up being router ones information. the status is up on both of the routers, but I'm unable to ping the remote gateway or any device behind it.[code]
View 5 Replies View RelatedAfter a few months of trouble-free ... the Cisco WRVS4400N V2 stopped working. i have tried to reset by holding the reset button for 30 seconds ... but nothing changes the red DIAG light remains on at all times
i have also tried two different versions of the Firmware Rescue Utility but all i get is "unable to scan"
How to setup VPN connection,
Head office : fortigate 200b firewall - SSL, IPsec
Branch office: WRVS4400N Wireless-N Gigabit Security Router with VPN
Both side have the public IP.
My WRVS4400N is not letting my VPN client through the router. I have checked the passthrough boxes for all 3 protocols. I have port range forwarding for my VPN connections to my SBS2008 box on port 1723.
View 5 Replies View RelatedI have a Linksys E4500 as the main router and would like to use the WRVS4400N as a bridge to extend the range of my network and also attach a NAS to it. Is this possible? I've been trying different options but have been unsuccessful.
View 1 Replies View RelatedLooking for a working Cisco VPN client for Windows 7. There seems to be an availabel download for a ver 5, but you have to be a reseller etc.. Where do I download the Windows 7 supported VPN client to access my WRVS4400N router? If none, should I use 3rd party - IF yes to 3rd party, which one would you suggest?
View 1 Replies View RelatedI bought a WRVS400N v2 to be used as an access point. Currently it is hooked up on my switch via a trunk port and is able to communicate with my gateway. Whenever I try to access an IP subnet other then the local IP address of the WRVS, I get a network unreachable error. To fix this for my local networks, I added the appropriate static route to cover my local LANs and that seems to work now. I tried to add route 0.0.0.0/0.0.0.0 using the web interface for internet access, but somehow it does not recognize this as a default route (quad zero!?). Does any know how I can set the default gateway in this router? Maybe, but hopefully not, I have to use the WAN port to create some kind of uplink and use one of the LAN ports to connect using the trunk port and route traffic for the clients over the WAN port .
View 1 Replies View RelatedI have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?