Linksys Wireless Router :: WRT 150N - Unable To Connect To Internet
Dec 13, 2011
I have had this router with no real problems for the past 2 years. As of now I can't connect to the internet through the router wired or wirelessly. I have tried all the hard resets and other tricks. I can go straight from my internet connection to my computer and it works fine. Once I go through the router using a lan cord all I get is limited or no connectivity. I have tried to access the router set up using the 192.68. etc but can't just states invalid address. Anything else to try or is this thing bricked ?
View 1 Replies
ADVERTISEMENT
Dec 25, 2012
I am currently trying to do a cascading LAN-LAN, my primary router is a d-link, my second router is a linksys 150N, I connected an ethernet cable to one of the 1-4 ports in the second router(150N with DD-WRT firmware), I tried logging into the 150N via 192.168.1.1(I did a hard reset so I have to get in and change it to 192.168.1.2) but I think i am going directly to the primary router. I tried connecting the 150N(secondary) directly to change the address to 192/.2 but I dont get anything, seems the internet connection to the router is not working. is there any other way? I had this working but I forgot the password and had to do a hard reset(this is a network back at my parents, I am here for the holidays) the way I had it working was LAN-LAN, Im not sure if the internet port for the 150N is damaged.
I tried connecting the internet cable from the 1st router to the internet port of the 2nd(150N) and didnt get anything.
I am about to think that maybe my 150N is faulty or at least the internet connection throught the blue port is not working.
View 9 Replies
View Related
Aug 13, 2012
Due to some reason I had to reset my linksys router WRT54G and now I am not able to connect to internet using my router. I tried coupld of settings followings some suggestion over internet sites but doesn't work for me. Still I get no network access message.
View 1 Replies
View Related
Sep 15, 2012
I just upgraded my router from an old wireless54G to an E1200.The wireless device I have on my Sony Viao PCG GRT-240G laptop is LAN-Express AS IEEE 802.11g miniPCI Adapter
-Initially I couldn't connect at all with this machine (however the other two newer laptops could) so I contacted the Linksys tech and he advised I should upgrade my laptop driver
-After much research about this I found a common fix was to upgraded drivers from the 2004 sony driver to atheros_wifi_9.2.0.480 drivers.
-After I did the upgrade I can connect to the router on the guest account and use the internet
However, on the Main account I can connect to the router but I have no internet connectionGoogle chrome gives error belowThe server at [url]... can't be found, because the DNS lookup failed. DNS is the network service that translates a website's name to its Internet address. This error is most often caused by having no connection to the Internet or a misconfigured network. It can also be caused by an unresponsive DNS server or a firewall preventing Google Chrome from accessing the network.How can I use one part of the network but not the other part? Shouldn't both the guest & main accounts use DNS lookup?
View 2 Replies
View Related
Apr 30, 2013
I have a few devices I cannot connect to my router or modem but my ps3 and 2 xboxes are connected. I have easy link and I try to add devices to it but it doesn't show me the same options it did before when I added my ps3, and ipod. Now I can't connect my psp or any phone to it, I have the WRT54GS v7.2, those are my only problems with the router nothing.
View 3 Replies
View Related
Dec 23, 2011
Ok group here's the issue. I have a E2500 router with a wired connection for my sons xbox and 2 laptops connected to it. The laptop I used to set-up the system will usually connect to the router but not allow me through to the internet then after a shutdown and repowering it connects. what to check? The othhitch. Both arer laptop connects without a e running vista home.
View 2 Replies
View Related
Sep 28, 2011
I am using the following model and version:
Model No.: WRT54G, Ver. 7.0
I am not able to connect to the internet through Linksys Wireless Router. I have tried pinging the default gateway of the ISP provided router IP from the router utility, "Diagnostic", but I am not able to ping it.
View 7 Replies
View Related
Dec 7, 2011
For some reason my wireless router recognized my pc, or my modem, Neither is it able to connect to the internet. All the lights are on but not flashing/blinking like they used to. I tried to run the setup over and it couldn't find the router even though everything was plugged correctly. I tried reseting the router but that doesn't even affect it. All the lights remain on with on blinking or flashing no mater what I do. Is there anyway for my router to work normal again or do I need to get a ned wireless router?
View 15 Replies
View Related
Mar 24, 2011
I have a new Linksys E2000, I was unable to connect one of my laptops to the internet, so I decided to call support with the problem, after 45min and not results, find out that the E2000 do not support the Atheros AR 5007, they told me that I need to get a new driver for my adapter. Fine but Cisco doesn’t have a Driver update for this problem or how to fix it, or at least send you a link where to get the fix.
View 4 Replies
View Related
Apr 5, 2011
I have had a problem with my WRT400N wireless Linksys router. Whenever my router restarts or if the DHCP lease expires, I'm unable to connect to internet. During this time I can access the router, but not the internet. Oddly something that seems to "fix" this is if I use my nintendo wii to access my wireless internet at that time, all computers on my network are able to access the internet. However this is annoying to do since this happens once a day from DHCP lease expiring. Using any other computer to attempt to access the internet at this time would be unable to get a connection until I do the "fix" with the Wii. WRT400N
View 8 Replies
View Related
Jan 13, 2012
I installed a new Media link MWN-WAPR150N router and I can connect two laptops and an i Pad wireless but when I try to access the Internet through a Dell Dimension 4550 desktop which is directly connected to the router, I get the message "Internet Explorer cannot display the webpage." I have tried unplugging the cable modem and router, downloading network drivers, repairing the connection, ip config /release and /renew, etc. and nothing has worked. The connection status shows as connected. I can ping the router successfully, but I can't ping a web site.
View 1 Replies
View Related
Mar 3, 2011
I've been unable to connect to the internet or even my Linksys router (192.168.1.1) from my main desktop. However, I can access the internet and the router by way of another (older) desktop and two laptops.This problem occurred after powering down and unplugging both desktops before a thunder storm. Later that night I powered on and had this issue. ISP didn't have any outages in the area. [code] Network and Sharing Center displays (this computer) with a line connecting to Unidentified Network and the red x between Internet. When viewing the status of that local network connection packets are being sent but 0 are received. TCP/IPv4 and 6 Properties are set to obtain IP/DNS automatically.I don't have any additional firewall software but windows firewall is enabled.
View 10 Replies
View Related
Apr 21, 2013
I am currently having problems connecting to my apartment internet through my Linksys E900 router. This problem occurred at random as well, I went to bed one night and I was connected with zero problems and when I woke up it no longer worked. It has been like this for a week now and I feel like I've tried everything, including buying a new Netgear router which didnt work either.Some basic info:
- Router is a Linksys E900
- My apartment complex provides free internet through Pavlov Media
- I can connect to the unsecured Pavlov wireless with no problem
- Before it stopped working, I had simply set up the router by plugging it into a wall ethernet jack and running the setup disc. This no longer works, it will set up the network but then I receive an error stating it is unable to connect to the internet.
View 8 Replies
View Related
Mar 2, 2011
My BEFSR81 router has never been a problem for over 10 years.All of a sudden I can not connect to the internet..I only use the router for connecting 2 PCs to the internet modem. I have not changed any configuration. tried my IPS COX recommendation to disconnect the power for about 1 minute then try again with no luck. CoX said they tried pinging my router but could not get a reading. While waiting for them to come up with a solution, I hooked one of my PCs directly to the modem. It worked. So I tried it with the other PC. But it didn't work right away. It kept trying to dial up for a connection. I finally got the WIZARD to get it configured correctly. I assume it must be a router problem because either one of my PCs can get an internet connection when hooked to the modem. I did not pusue any further with COX, THEIR AUTOMATED TROUBLE SHOOTER WAS GETTING ON MY NERVES.Should I take the time to resolve the issue with the router or buy a new or refurbished router? If the task isn't too complicatged, I am willing to try and fix it.
View 1 Replies
View Related
Jun 22, 2012
programming wrt 150n Linksys to access my IP camera from outside my network. My camera is a Sony SNC-Z20N.In my router I have disabled the firewall
View 2 Replies
View Related
May 31, 2011
OS - Vista Home Premium x32 I have a modem (Comcast) connected to my router (Linksys wireless-g /wrt54g v6) connected to my desktop which runs Vista.recently i am unable to connect to internet using my desktop, but I am still able to use my wireless devices such as wii, laptop, phone, ipad etc. with problem When I first boot up computer I receive error UPnP device host has stopped working. I close that and I have no network connections (linksys or LAN connections-icons) in my network and sharing area. Nothing is listed. When i click diagnose issue i receive the follow error A CABLE IS NOT PLUGGED INTO THE NETWORK ADAPTER "LOCAL AREA CONNECTION* 12" I have changed ethernet cords but still the same error. Nothng has been changed and as stated worked fine 2 days ago. I also did IPCONFIG and all i receive are ETHERNET ADAPTER LOCAL AREA CONNECTION* 12 MEDIA STATE.....MEDIA DISCONNECTED and so on. No IP address is listed.
View 4 Replies
View Related
Jun 4, 2011
I am unable to connect to the internet with my XP computer. I am running Apple Air Port as my router. The wireless network has an iMac, an IBM Think Pad(XP SP2)and a Dell XPS 410 (XP SP2). I am using WPA security and the Dell will not connect while the other two computers always connect. My wireless network is broadcasting, but when I try to connect after entering the proper key, it attempts to connect but appears to time out and displays the available wireless network. I tried reinstalling the drivers, but no success. Device Manager says the card is working and enabled.
View 5 Replies
View Related
Feb 17, 2012
I am having a trouble in setting up the new router, Medialink MWN-WAPR 150N with my laptop. I followed what the manual asked to do step by step, but at the end, a laptop detected strong signal for both wired and wireless, but it does not allow to connect to internet from both my laptop and smart phone. [code]
View 3 Replies
View Related
Jan 7, 2012
I have a VirginMedia 50Mps wireless router that runs 4 wired connections. These are all working fine and have Internet connection. When the router was installed I could also connect to the internet wirelessly on my Laptop which is running Windows Vista Home Premium. But of late I have been unable to connect to the Internet on the Laptop. When you place the mouse pointer over the Icon in the bottom right hand corner, the following message comes up : Currenlty connected to:Unidentified(virginmediaxxxxxxxx) (where xxxxxxxx is a numeric identifier for the modem). Access: Limited connectivity or sometimes it says Access : Local only.
View 4 Replies
View Related
Jan 19, 2013
I am unable to connect to the internet through my wireless router. However, I can connect using neighbor's wireless connection and other laptops in my home are able to connect to the internet using MY wireless connection. The problem started suddenly, I used to be able to connect, then I had the problem so I rebooted and that resolved the issue temporarily. I tried disabling the wireless adapter card then rebooting, this did not work. I also unchecked the TCP/IPv6.
View 4 Replies
View Related
Aug 13, 2011
I am not able to connect my HP laptop (Windows Vista) to the internet via a wireless router/high speed internet.My internet service provider confirmed that it is a problem with my HP laptop.I have a Linksys router. My other laptop (Sony) connects fine.I have tried two browsers on my HP laptop to access the internet with no luck.My HP laptop does say that I am connected to the wireless network.
View 9 Replies
View Related
Feb 7, 2011
The internet at my parents house has recently gone on the fritz..the wireless router is a N600 Wireless Dual Band Router WNDR3400..The computers of the house are able to connect to it..But it does not allow internet connections..The 3 computers are an HP Laptop running windows 7.a Dell Dimension E521 Running windows 7 & and an older HP Walmart special running XP.They can connect to outside systems and through a wired connection to the Modem from Cable vision. They replaced the wireless router and the problem continues.Internet is capable by plugging directly into the Cable vision router,unfortunately do not have the cables to try through the Netgear router to test that out..
View 3 Replies
View Related
Sep 21, 2011
So here is the issue:
When I connect my modem directly to my computer (modem > computer) it works just fine, internet connects and everything through the direct ethernet connection.But when I connect the modem to the router and then try to connect wireless with any other computer (modem > router > wireless) nothing works. Not even when I have it connected directly from the router to the ethernet on the main computer. (Which has ALWAYS worked until now.
View 1 Replies
View Related
Mar 3, 2011
I have a Cisco Linksys router that I have been using for about 6 weeks just fine with Windows Vista on an Acer Laptop. We had some power outages (about 3, less than 30mins each) and the internet was down for nearly 48 hours early this week. Now that it is up, I was able to connect to my router for a few hours. When I shut my laptop off and about 2 hours later tried to access the web again, I found that I couldn't unless I hardwired from the modem.I've done the windows repair network connection and the Cisco Network Magic fix- (It says things like flushing DNS cache while doing its thing). Both say my network key is wrong. No one else in the house could have changed it, I was the only one home.I've power cycled both the router and modem. I've turned my laptop off and rebooted. I used the manufacturers settings to try to go in and see what happened. I can't type the router's direct IP and get into like it says I should in Firefox.
The one thing I've noticed is that prior to the outage- my router had a "name" that I named it, while now it's back to linksys_numbers_letters. However, I was still able to connect after the outage at the beginning.
View 2 Replies
View Related
Oct 2, 2012
Just purchased a ea4500 router. Have setup multiple computers/devices already and works great. This computer (HP dv6000 running Win Vista home prem) however will not connect to the internet. It states that it is connected to the router (computer sees router), using the cloud connect app on my iphone i can see this computer, but will not allow access to the internet (local connection only). It works fine with the wired connection. When attempting to use the cloud connect software, it says it was unable to complete the install. Have attempted trying while connected by wire as well, same result. Have deleted the wireless connection and allowed software to find connection, still same result, cannot install. Wireless worked perfectly with previous router (WRT54G) three days ago.
View 6 Replies
View Related
Feb 15, 2013
My e1000 was working fine until it was accidentally unplugged. Now it doesn't work. I downloaded the set up program from the site and tried to run it, but it does not recognize an internet connection when I have the modem connected to the router and the router connected to the PC. The internet works when I connect the modem directly to the PC. I have unplugged everything and restarted the PC several times and tried running the software again, but no dice.
View 4 Replies
View Related
Sep 8, 2010
I my parents have a WRT54G linksys router, they have a DSL modem. Everything was working fine with the wireless network until one random day POOF! the wireless no longer would connect on laptops. However, the internet is working just fine with the computer that is hardwired up throught the router. Since this is working it lets me know that the router is working fine and routing the connection through hardwire. Hard wired works on laptops but all laptops are unable to join the network and most of the time it will not show up in the list of available networks.Even my iphone wont connect saying unable to join network. We bought a brand new linksys router and same problem. I then took his old router to my house and hooked it up...and WOW it works as it should all devices can connect...even my iphone.
View 2 Replies
View Related
Apr 13, 2013
I just bought the EA6500 last week. Had to RMA it on Monday and got the new one today. The issue still persists. The power light is constantly blinking and my computer is unable to obtain an IP address from it. I contacted tech support and was unable to get the issue resolved so I had it exchanged believing it was defective. The new one does the same thing. When I connect my computer to it, the light on my Ethernet port stays a solid orange instead of green like it does for my usual router. The Cisco light is constantly blinking.
View 9 Replies
View Related
Feb 20, 2010
Checked cable router (brighthouse), working. Router (all lights on but network traffic flashing indicates one way traffic). So I go to my wife's computer. It too has no connection. I open my laptop to connect to the wireless, IT WORKS! Pull power on Cable Modem and Router, wait 60 secs, power up Cable Modem and then power up Router (I know it wasn't nec to do modem but I wanted a clean start). Wireless is still working, no LAN. I can't even connect 192.168.1.1. Linksys software says it can't detect the modem. Reset time, hit the magic button in the back and sure enough everything stops working (which I figured). Still can't connect to it, and now I've lost wireless. I connect computer directly to Cable Modem and type this message. Seems to me that Router has failed.
View 3 Replies
View Related
Dec 14, 2011
Im running a linksys wireless router, WRT54G V6 with firmware 1.02.8. It worked before I moved after I moved I can't connect via wireless. hard line works. i've tried resting to factor, i've tried not using ses, not using custom ssid. I've rest it like 5 times retarted the computers. I've hit the little cisco systems button on the front, this makes it work for a few minutes. When I hit the button it will go out then come back on white, and blink around 1-2 blinks per second, it will do this for maybe 1-2min. then stops and changes back to orange. and i get nothing from it. the WLAN light is on like it's working but I cannot detect it with my desktop or laptop, can i can detect 3 other routers around me. I've tried pretty much everything i know to do, tried flashing it, updating, about the only option i have left is throwing it out the window.
View 2 Replies
View Related
Oct 9, 2011
I've had my E3000 for almost a year now and it's been great - until recently. Latencies have become patchy for some users and most surprisingly, the 5GHz network has stopped using two channels. I did a 30/30/30 reset on it a few minutes ago and re-configured the whole thing. It's set to use 40MHz Only and WPA2 Personal, but speeds at the physical layer are still just 144 Mbps and in the web interface's Status page it clearly says "20 MHz".
Why might this be? It was fine for so long, only to refuse to use two channels now. I've checked what the other wireless networks in my area are like, and none of them are even 5GHz-capable as far as I can tell, so the relevant spectrum shouldn't be overcrowded. It's rather nice to have the two channels for NAS transfers and streaming and such.
After manually specifying a base channel (48 at the moment), it actually kicks into 40MHz. The problem is now that my clients, both using a WUSB600N, are getting "Unable to connect to (SSID)" pretty much instantly after clicking the network in Windows.
View 1 Replies
View Related
Aug 23, 2011
I'm using E4200 with latest 1.0.02 firmware and found I can not connect to VPN with my iPhone4 by WiFi.Googled a bit and found it's a common problem for Cisco routers when wireless devices can not connect to VPN but wired ones connects with no problems.\
View 3 Replies
View Related
Sep 10, 2011
So, I've been having problems with connecting my HTPC to the E2000. I had an old D-link router + USB Wireless N adapter, but after the Dlink died, I bought the E2000, and upgraded to a faster N Adapter. Anyway, connection had been sketchy using the WPA/WPA2 encryption. I turned it off completely, and did get some better wireless speeds. I couldn't leave it open, though, as there are tons of laptops around my apartment that end up connecting to my network. Connecting wirelessly using that particular adapter continued to give problems. Two blackberries plus a Nookcolor connect with no issues (maybe because they're wireless G, who knows).
I then decided to reset the router by simply pressing and holding the reset button as I've done on all my other routers. It did reset, and reboot, but when it came back on, it would no longer connect to the internet. I've connected directly to my modem, and that works fine, but once I connect to the router...nothing. I did a hard reset (30/30/30), and that cleared everything, it seemed. The HTPC now connects easily, but there is still no internet connection. This is proving to be very frustrating.
Is there something I could have done wrong by doing that very first reset? Is there anyway to configure to get back my internet connection?
View 4 Replies
View Related
