Due to some reason I had to reset my linksys router WRT54G and now I am not able to connect to internet using my router. I tried coupld of settings followings some suggestion over internet sites but doesn't work for me. Still I get no network access message.
View 1 RepliesI am using the following model and version:
Â
Model No.: WRT54G, Ver. 7.0
Â
I am not able to connect to the internet through Linksys Wireless Router. Â I have tried pinging the default gateway of the ISP provided router IP from the router utility, "Diagnostic", but I am not able to ping it.
OS - Vista Home Premium x32 I have a modem (Comcast) connected to my router (Linksys wireless-g /wrt54g v6) connected to my desktop which runs Vista.recently i am unable to connect to internet using my desktop, but I am still able to use my wireless devices such as wii, laptop, phone, ipad etc. with problem When I first boot up computer I receive error UPnP device host has stopped working. I close that and I have no network connections (linksys or LAN connections-icons) in my network and sharing area. Nothing is listed. When i click diagnose issue i receive the follow error A CABLE IS NOT PLUGGED INTO THE NETWORK ADAPTER "LOCAL AREA CONNECTION* 12" I have changed ethernet cords but still the same error. Nothng has been changed and as stated worked fine 2 days ago. I also did IPCONFIG and all i receive are ETHERNET ADAPTER LOCAL AREA CONNECTION* 12 MEDIA STATE.....MEDIA DISCONNECTED and so on. No IP address is listed.
View 4 Replies View RelatedI my parents have a WRT54G linksys router, they have a DSL modem. Everything was working fine with the wireless network until one random day POOF! the wireless no longer would connect on laptops. However, the internet is working just fine with the computer that is hardwired up throught the router. Since this is working it lets me know that the router is working fine and routing the connection through hardwire. Hard wired works on laptops but all laptops are unable to join the network and most of the time it will not show up in the list of available networks.Even my iphone wont connect saying unable to join network. We bought a brand new linksys router and same problem. I then took his old router to my house and hooked it up...and WOW it works as it should all devices can connect...even my iphone.
View 2 Replies View RelatedChecked cable router (brighthouse), working. Router (all lights on but network traffic flashing indicates one way traffic). So I go to my wife's computer. It too has no connection. I open my laptop to connect to the wireless, IT WORKS! Pull power on Cable Modem and Router, wait 60 secs, power up Cable Modem and then power up Router (I know it wasn't nec to do modem but I wanted a clean start). Wireless is still working, no LAN. I can't even connect 192.168.1.1. Linksys software says it can't detect the modem. Reset time, hit the magic button in the back and sure enough everything stops working (which I figured). Still can't connect to it, and now I've lost wireless. I connect computer directly to Cable Modem and type this message. Seems to me that Router has failed.
View 3 Replies View RelatedIm running a linksys wireless router, WRT54G V6 with firmware 1.02.8. It worked before I moved after I moved I can't connect via wireless. hard line works. i've tried resting to factor, i've tried not using ses, not using custom ssid. I've rest it like 5 times retarted the computers. I've hit the little cisco systems button on the front, this makes it work for a few minutes. When I hit the button it will go out then come back on white, and blink around 1-2 blinks per second, it will do this for maybe 1-2min. then stops and changes back to orange. and i get nothing from it. the WLAN light is on like it's working but I cannot detect it with my desktop or laptop, can i can detect 3 other routers around me. I've tried pretty much everything i know to do, tried flashing it, updating, about the only option i have left is throwing it out the window.
View 2 Replies View RelatedIPOD Touch 4G that will not connect to internet. it sees the network, requests a password but will not connect. Have been entering the same 8 character password the router uses.
View 5 Replies View RelatedI have used this router without issue for several years at two addresses on 3-4 computers. Two years ago, the cable tech (Time Warner) hooked it up when he installed the modem (Surfboard SBV5220) which also provides phone service.Â
View 5 Replies View RelatedI have Lynksys router WRT54G. I have 3 laptops in house connecting to internet with no problem. A new person has moved in with a laptop that has windows 2000. The new person is not able to get an internet connection.
View 9 Replies View RelatedRouter: WRT54G
Network: 802.11g (and I'm using WEP)
Wifi Adapter: Intel R Centrino R Ultimate-n 6300 AGN
No. of devices connected to wireless network: 5
My problem is that whenever 2 devices have joined the wireless network, I will not be able to do so despite placing the laptop or iPhone right next to the router, hence getting excellent signal strength. Or, if I am already connected to the network, I get knocked out repeatedly. I don't think it is a hardware or software issue because I'm still able to connect and get a very stable connection after someone leaves the wireless network.This is getting frustrating and I have tried all ways and means to resolve this but to no avail. Is this about some setting that I can tweak, e.g. to allow more users onto the network? But this has already been configured to '50'!
I am replacing a WRH54G with a WRT54G. Â First I unplugged everything and waited 5 minutes. Then I plugged my ethernet cord from the DSL modem into the WRT54G. Then I plugged in the DSL modem. I waited for the lights to stop blinking. Then I plugged in the WRT54G and waited for LEDs to show connection. Then I plugged the ethernet cord from the WRT54G to the computer. Then I turned on the computer. I was able to access the Interface for the WRT54G but I was not able to connect to the internet. I tried power cycling multiple times both the DSL modem and the WRT54G. I was unable to access the internet. Finally I plugged the WRH54G back in and everything worked fine. why the old WRH54G can connect to the internet and the WRT54G cannot?
View 9 Replies View RelatedMy router used to work. I updated the firmware to 4.21. xx and after that I can't connect to internet.When I connect directly to modem, I can go to the internet . I power recycled etc but when I connect to the router, it says limited connectivity. It shows autoconfigurtion ip:169.254.251.135. I don't know why this is so.I don't have the setup cd disk but I read the users' guide and it seems that I really don;t need the cd. But no matter what I do , I can't get to 192.168.1.1 .
View 4 Replies View RelatedI have a wrt54g v5 router. I cannot connect to the internet through my router. I called the cable company and they told me that the router probably reset from a power outtage and reconnect. i power cycled, i tried to log onto the router via 192.168.1.1 but the connections were spanish to me.
View 2 Replies View RelatedI have a WRT54G router and a Dell computer. I have been connecting wirelessly to this router with this computer for about 3 years. Now, the computer sees the router but it won't connect to the internet. I have other computers that connect fine, so I thought it was the wireless adapter in my computer. However, I went to someone else's house and connected perfectly.
View 3 Replies View RelatedWhen i connect my computer directly to my modem i could connect to the internet but when i connect the modem to the internet port on the WRT54G and then connect my computer to one of the ports on it i can't connect to the internet at all.
View 5 Replies View RelatedI cannot connect to the internet via the wireless network from my router. Currently, I can connect to the wireless network, however I cannot access the internet, but I am able to access the internet with an Ethernet cable in the same router. This is a fairly recent development as we have used this router for wireless internet access (our modem has a wireless network built into it, but it is unreliable) for upwards of 8 months now without problem. One day it simple restored itself to the default name and we were no longer able to access the internet through the wireless portion.
Router: WRT54G Version 6.0
i just updated my firmware on my wrt54g ver 2 router, went through all the steps it updated successfully after that i hit the reset button and unplugged the router as tehe online instructions said to. Now i can't connect to the interent at all with either of my two wired computers or through the wireless. All the lights on the front of the router are on like the power, internet, and wireless connectivity. Also the the two WAN ports my computers are connected to in the router the lights are on and it's recognising them. But I can't connect to the internet or even see the router on my network settings. Somone suggested to reconfigure the router but when i go to set up new connection my computer doesn't detect the router and also i cant connect to the router using the ip address 192.168.1.1/ since there is no internet connection. Is there a way to get to the router options or a way to revert it to its old firmware.
View 6 Replies View RelatedI have WRT54G router.  The VIZIO VBR231 unit finds the network OK and indicates it is connected, but nothing will stream, and  when I run a Network Test it gives me this 3 line error:
Connection to 0.0.0.0... successfully established
Resolving... could not be established
Please check your connection and try again.
Â
The VIZIO support folks were not beneficial at all, and said something about Port 80 or Port 43 not being open or available. Â When I talked to linksys support, they said I needed to add the VIZIO player's IP (which appears to be 0.0.0.0 in the system settings). Â I poked around a bit, including the Port Forwarding tab on the router setup, but could not see a way to assign 0.0.0.0 to one of these ports, and I am hesitant to experiment.
Â
I'll probably just return the unit to Costco, but I'm trying this forum as a last ditch effort. Â BTW I have a VIZIO internet TV that I love, and that had absolutely no problem at all connecting to the wireless.
I have a Linksys wireless router model WRT54G (not sure the exact model, it's not in front of me right now). It has worked flawlessly for the past several years, but for some reason has recently stopped working. I confirmed it's not a problem with the DSL Modem, as I can hard wire connect to my laptop and the internet works fine. It's clear something is wrong with the wireless router. I've tried unplugging, hitting the reset button on the back, and nothing has worked. My computer is able to recognize/locate the router and connect, it's just that I can't connect to the internet. One thing I've noticed under the wireless connection is that the computer is able to "send" packets, but not "receive." My experience is that this is always the case when I experience connection problems, but I have no idea what that means. I was going to call the Help Line, but I see it costs $30 which is likely more than my router is worth and probably 1/2 to 1/3 the cost of a new one so I am trying to troubleshoot myself.
View 8 Replies View RelatedI have a WRT54G router that's worked for a very long time. I had WEP security set up and it worked fine until recently. About a week ago my three year old son managed to reset the router (I'm still not sure how). When I go onto the web-based setup page I am unable to change the wireless security setting. I select an option from the drop down menu but then the page reloads and nothing has changed.
View 1 Replies View RelatedI am unable to login to my router ? I have tried to reset my router and am still unable to login to the online control panel. The steps that I went about resetting the router were pushing the reset button for 30 seconds. That did not work so I pushed the reset button for 30 seconds, unplugged the router while continuing to hold the reset button for 30 seconds, plugged the router back in while holding the reset for 30 seconds.
View 6 Replies View RelatedI just upgraded my router from an old wireless54G to an E1200.The wireless device I have on my Sony Viao PCG GRT-240G laptop is LAN-Express AS IEEE 802.11g miniPCI Adapter
Â
-Initially I couldn't connect at all with this machine (however the other two newer laptops could) so I contacted the Linksys tech and he advised I should upgrade my laptop driver
Â
-After much research about this I found a common fix was to upgraded drivers from the 2004 sony driver to atheros_wifi_9.2.0.480 drivers.
Â
-After I did the upgrade I can connect to the router on the guest account and use the internet
Â
However, on the Main account I can connect to the router but I have no internet connectionGoogle chrome gives error belowThe server at [url]... can't be found, because the DNS lookup failed. DNS is the network service that translates a website's name to its Internet address. This error is most often caused by having no connection to the Internet or a misconfigured network. It can also be caused by an unresponsive DNS server or a firewall preventing Google Chrome from accessing the network.How can I use  one part of the network but not the other part? Shouldn't both the guest & main accounts use DNS lookup?
I have a few devices I cannot connect to my router or modem but my ps3 and 2 xboxes are connected. I have easy link and I try to add devices to it but it doesn't show me the same options it did before when I added my ps3, and ipod. Now I can't connect my psp or any phone to it, I have the WRT54GS v7.2, those are my only problems with the router nothing.
View 3 Replies View RelatedI have had this router with no real problems for the past 2 years. As of now I can't connect to the internet through the router wired or wirelessly. I have tried all the hard resets and other tricks. I can go straight from my internet connection to my computer and it works fine. Once I go through the router using a lan cord all I get is limited or no connectivity. I have tried to access the router set up using the 192.68. etc but can't just states invalid address. Anything else to try or is this thing bricked ?
View 1 Replies View RelatedOk group here's the issue. I have a E2500 router with a wired connection for my sons xbox and 2 laptops connected to it. The laptop I used to set-up the system will usually connect to the router but not allow me through to the internet then after a shutdown and repowering it connects. what to check? The othhitch. Both arer laptop connects without a e running vista home.
View 2 Replies View RelatedFor some reason my wireless router recognized my pc, or my modem, Neither is it able to connect to the internet. All the lights are on but not flashing/blinking like they used to. I tried to run the setup over and it couldn't find the router even though everything was plugged correctly. I tried reseting the router but that doesn't even affect it. All the lights remain on with on blinking or flashing no mater what I do. Is there anyway for my router to work normal again or do I need to get a ned wireless router?
View 15 Replies View RelatedI am running a Linksys Wireless G 2.4 GHz Broadband Router Model WRT54G. Â I am unable to open any ports. Â I upgraded to the latest firmware yesterday but still am unable to open any ports. Â I even turned off my Symantec Internet Security Suite Firewall but still am unable to open any ports. Â
View 2 Replies View RelatedI'm unable to access my linksys wireless g broadband router (WRT54G)'s access gateway. (192.168.1.1)The gateway page doesn't load, at all. It doesn't ask for the user or password at all. On any of my internet browsers (firefox, and internet explorer)Anyway of fixing this would be appropriate.
View 2 Replies View RelatedI have a new Linksys E2000, I was unable to connect one of my laptops to the internet, so I decided to call support with the problem, after 45min and not results, find out that the E2000 do not support the Atheros AR 5007, they told me that I need to get a new driver for my adapter. Fine but Cisco doesn’t have a Driver update for this problem or how to fix it, or at least send you a link where to get the fix.Â
View 4 Replies View RelatedI have had a problem with my WRT400N wireless Linksys router. Whenever my router restarts or if the DHCP lease expires, I'm unable to connect to internet. During this time I can access the router, but not the internet. Oddly something that seems to "fix" this is if I use my nintendo wii to access my wireless internet at that time, all computers on my network are able to access the internet. However this is annoying to do since this happens once a day from DHCP lease expiring. Using any other computer to attempt to access the internet at this time would be unable to get a connection until I do the "fix" with the Wii. WRT400N
View 8 Replies View RelatedI have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed."Â I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it.Â
View 9 Replies View RelatedI'm trying to setup a Linksys wireless-g router model number WRT54G with my DSL connection. I followed the basic instructions that came with the router and towards the end of the process it says detecting network settings with a % bar. The bar fills to 100% and then asks for a password. I've tried the password my DSL company gave me along with various other things like admin etc. After I enter the password I hit enter and it just asks me for the password over and over again.
View 9 Replies View RelatedI've been unable to connect to the internet or even my Linksys router (192.168.1.1) from my main desktop. However, I can access the internet and the router by way of another (older) desktop and two laptops.This problem occurred after powering down and unplugging both desktops before a thunder storm. Later that night I powered on and had this issue. ISP didn't have any outages in the area. [code] Network and Sharing Center displays (this computer) with a line connecting to Unidentified Network and the red x between Internet. When viewing the status of that local network connection packets are being sent but 0 are received. TCP/IPv4 and 6 Properties are set to obtain IP/DNS automatically.I don't have any additional firewall software but windows firewall is enabled.
View 10 Replies View Related