Linksys Wireless Router :: WRT54G - XBox Can See Network But Will Not Connect To It
Nov 29, 2011
Yesterday i was playing online on my Xbox 360, and was disconnected from the internet. I came downstairs to reset router/modem, once doing so i went into the router settings for my Linksys WRT54G. My modem by default uses the 192.168.1.1, so my router was 192.168.2.1... So i powercycle, log into router settings through 192.168.2.1 and start setting up my port forwarding for the xbox ports. Saved Settings, and the page would not load to say "Settings Saved". Closed the window and now my pc says no internet connection. I had to create a VPN broadband connection to even use the internet on my pc. I can no longer log into 192.168.2.1 for my router, nor can i access 192.168.1.1 to even get into my modem settings.. I'm using windows 7, and the automatic troubleshooting guide tells me to powercycle my modem. My xbox can still see my wireless network "linksys" but will not connect to it, even with the VPN connection i am still hooked though my router and modem.. Im afraid that my router just out of nowhere "died"..
View 2 Replies
ADVERTISEMENT
Aug 1, 2012
I cannot get my xbox to be able wrt54g . Device on comp does not read xbox yet xbox piccks up router
View 4 Replies
View Related
May 24, 2012
My network is discoverable, but my machines will not connect (they were connected previously). They can connect to the 2.4gHz network, but not the 5 (I use the 5 for streaming media and gameplay). Windows 7 says it's unable to connect.
View 8 Replies
View Related
Nov 29, 2007
I have a xbox 360 that I want to connect to xbox live with, using my home network. Every time I try to connect to xbox live the only part that fails is the connecting to xbox live part. This is how my network is set up. I have Cox Cable as my ISP, a Linksys WCG200 gateway(v2), and WRT54GS(v7). The cable wire is connected to the WCG200 gateway, then an Ethernet cable connects the gateway to the WRT54GS router, and finally an Ethernet cable connects the router to my xbox 360. I have contacted Cox, Linksys, and Microsoft about the situation and they all say the problem is the version of the router. Someone told me that I may just need to change the firmware, but I don't know how to do that.
View 9 Replies
View Related
Nov 18, 2012
I have a WRT54G version 3.. i have finished installed it using the web based set up but i can't connect my mobile through the wireless network.
View 1 Replies
View Related
Nov 13, 2009
I have been using this router fine for a year now. Now I can only get on the internet if I am directly plugged into the modem. It says I have limited connectivity. My ISP is Comcast. I have tried resetting the router with no luck. I have tried to update the drivers but I cannot even log into 192.168.1.1. I am in dire need of the wireless cpability. When I go to the run command and type ipconfig it tells me I have no default gateway.
View 9 Replies
View Related
Aug 28, 2011
So I have a WRT54G router since a couple of years now. Laptop (Win7 64bit), ipod, ipad, phones can connect to it without a problem, but new computer (Win7 64bit) can't. I can connect the PC via ethernet without a problem though.
Â
I powercycled my devices, I changed broadcasting options off and then back on, changed my security mode, tried the MAC Cloning (after doing the MAC Cloning, I lost internet connectivity even through ethernet), resetted my security settings, changed SSID, I'm broadcasting through channel 11 2.462. I also tried deleting the HomeGroup
Â
Important fact: the network is in the list of available wireless network, but Signal Strength is No Signal and I can't connect to it. My network adapter is ASUS 802.11n Wireless LAN Card, drivers are up to date. I've upgraded to the latest router firmware.
[Code]....
View 4 Replies
View Related
Dec 12, 2012
I'm having trouble connecting my 360 to the wireless router to gain Internet access.I use my phone's Wi-Fi to gain internet access with NO issues. My current setup: NetGear Wireless router is connected to my D-Link wired router, and I can access the internet no problem. (10 MBPS down, 5MBPS up)When I try to connect the 360 to the Netgear Wireless router, it connects to the Network, but Internet test it reads "DNS error - The router or modem may mot be automatically providing DNS settings. Try a manual DNS setting instead."(Next suggestion) "DNS Error - If you have a PC that can successfully browse the web, check it's network properties to find the DNS address it uses..."Now, I have XBMC running on my computer, and the 360 can access the network so it shows up under Video Apps so I can see a file list to stream movies. When I try to run a movie, it says I must download an update - so I can't watch the movies at all.I juso set it up so I can access the Network AND Internet.Again, Netgear wireless router (which 360 connects to) connected to D-Link wired router.
View 10 Replies
View Related
Mar 9, 2011
I'm sure it's on here but because I dont understand the name of what I'm looking for, I'm having trouble searching. My main network is setup for wireless via a netgear wndr3700. I'd like to use my old linksys wrt54g v5 to connect to that network wirelessly and allow me to connect my xbox via wired ethernet. Basically instead of buying a wireless adapter for the xbox, i'd like to know if/ how i can use my linksys router instead.
View 13 Replies
View Related
Nov 28, 2012
So i got the Asus RT-AC66U router and ive setup everything as far as the 2.4 and 5ghz wireless goes. However, for some reason i cannot get my xbox 360 to connect to the wireless network. I tried both the 2.4 and 5ghz network. It sees the network just wont connect. also ive tried to manually add the ip and dns settings to no avail either
View 11 Replies
View Related
Aug 22, 2012
I've recently started studying for the CCNA exam and one of the first things you learn is the type of cabling required between devices.Basically, I got curious and checked to find that my pc and e2000 router are connected via a straight-through cable even though it's supposed to be that a router and pc share the same pin layout and should be connected via crossover cable. It's the same story with my xbox and ps3 (also wired directly to the router via straight-throughs).
View 1 Replies
View Related
Mar 9, 2012
My Xbox 360 will not connect to my Cisco E2000 wireless router. It can find the router, but when the Xbox tests the connection it can’t establish a connection with the router. Ironically when I try to use the guest account it can establish a connection with the router before I run in to trouble.
View 1 Replies
View Related
Dec 21, 2011
I got the new E4200 router as I had issues with my old router. I was able to DMZ my console with the old router. But with my new router my xbox IP has changed and I want to know which numbers to use and how to DMZ my Xbox with Cisco Connect.
View 7 Replies
View Related
Sep 9, 2012
More often than not, when my son wants to play on Xbox Live, the Xbox won't connect to Xbox Live. It will connect to the network and the internet but not Xbox Live. After running the connection test, the suggestion is to reboot the modem and router. It works after rebooting those two devices. Why does this happen so often?Â
View 8 Replies
View Related
Nov 6, 2012
I have a Cisco E2000 and I have multiple devises that work but not my xbox 360. I have 2 computers 2 iphone 4s 2 ipods iphone 3gs
They all connect to the internet fine. My Xbox 360 never connected. the xbox can connect to the router. Then the router cannot connect to the internet.
View 3 Replies
View Related
Apr 15, 2012
I just need a a way to connect my xbox 360 to the internet. I considered buying a WET610N and was wondering if it will connect to my E2000? I can't use one of microsoft adaptors because something is wrong with my usb ports. Or if it is possible am I able to connect a WET54G? I'm not looking to play online just get connected wirelessly. Will either one of these bridges connect to the E2000?
View 1 Replies
View Related
Sep 23, 2012
It worked fine for my PC's and Xbox, but I had disconnected my router for a while, plugged it back in and my xbox simply cannot receive any connection. I should also note that I use an ethernet cord (I don't use it wirelessly) and it has nothing to do with the ethernet cord (I've tried several). Using network magic, it does confirm that a connection to the game console and the router.I've looked through the forums and all of what I found, are NAT problems/issues or fixing a wireless issue, but not an issue when using an ehternet cord.
View 1 Replies
View Related
Jul 23, 2011
As a temp work around I have two SSID now, one for everything else running WPA2 and one for xbox running WPA. The xbox seems to not like the router on WPA2 and though this would make one think, oh its your xbox, thats not always the case with devices. Some just may happen to want to use a feature the device doesn't support correctly and other devices are able to work around it while ones not so I cant for sure blame on xbox.
View 1 Replies
View Related
Aug 12, 2011
WRT610v2 running latest firmware.
xbox 360 sees both the 2.4 network (ssid = network1) and the 5.0 network (ssid network2) when it does its scan.
Â
Initially, xbox showed network strength for 2.4 network at 3 out of 4 bars and 5.0 network at 1 out of 4 bars. Connects to 2.4 network just fine, Won't pull an ip address and reports "Not connected" when I select the 5.0 network.
I tweaked the wireless settings per some suggestions I found in this forum and now it shows the 5.0 network at 4 out of 4 bars signal strength. Also turned security on and off and xbox 360 reported the changes in security on the 5.0 network. So the xbox 360 is definitely seening the 5.0 network. and can tell if it is running WPA2 or not. If it can see the 5.0 network and recognizes what security and network type (infrastructure) is set, would would stop it from connecting to the WRT610n router and getting an IP address? No mac filters or firewalls are set and, again, connects just fine and gets an ip address if I select the 2.4 (network1 ssid) instead.
View 2 Replies
View Related
Oct 22, 2012
I have a few devices at my home that connect wirelessly to the internet via wrt54g. I want to connect to the internet via VPN. I would like to find out if it is possible to connect WRT54G router to the VPN via PPTP or L2TP? The VPN company provided me with PPTP and L2TP credentials. I can access vpn via OpenVPN on computers but I would like my TV connect to the internet also via VPN.
View 5 Replies
View Related
Jul 26, 2012
I have a WRT54G router and although the local connection works the wireless does not. I have tried unpluging the router and replugging, holding the reset button for 30 seconds powering off 30 seconds and then plugging back it for 30 seconds. The ipconfig /all is below.
Â
Windows IP Configuration
Host Name . . . . . . . . . . . . : TN-PCPrimary Dns Suffix . . . . . . . :Node Type . . . . . . . . . . . . : HybridIP Routing Enabled. . . . . . . . : NoWINS Proxy Enabled. . . . . . . . : NoDNS Suffix
[Code].....
View 5 Replies
View Related
Sep 22, 2011
Router: WRT54G
Network: 802.11g (and I'm using WEP)
Wifi Adapter: Intel R Centrino R Ultimate-n 6300 AGN
No. of devices connected to wireless network: 5
My problem is that whenever 2 devices have joined the wireless network, I will not be able to do so despite placing the laptop or iPhone right next to the router, hence getting excellent signal strength. Or, if I am already connected to the network, I get knocked out repeatedly. I don't think it is a hardware or software issue because I'm still able to connect and get a very stable connection after someone leaves the wireless network.This is getting frustrating and I have tried all ways and means to resolve this but to no avail. Is this about some setting that I can tweak, e.g. to allow more users onto the network? But this has already been configured to '50'!
View 7 Replies
View Related
Feb 1, 2009
I could not log into any of the 4 FTP sites that I normally update without immediately getting disconnected. The message I am getting from the servers is "Port command failed, error loading directory - disconnected". To save some time and posts, here are the facts....1.) It is definately not my DSL modem. When I connect directly with the modem, without a router, I can connect to FTP fine2.) I have already done a /flushdns in IPconfig.3.) I have already done the typical power off/power on/reboot procedure numerous times.4.) I have already tried PASV mode, and tried turning PASV mode off as well.5.) My login information is correct, and I have problems on multiple sites.6.) This problem has been reported before by other users of WRT54G, but the other forums I see have no solution to the problem.7.) I have already tried using other PC's and different FTP clients on my home network. No matter which PC or laptop I use behind the router firewall, I can't maintain FTP connection. 8.) I have never had to open ports to be able to connect to FTP, since I am the one doing the request. I did also try opening ports 20 and 21. 9.) XP firewall is disabled. 10.) I have tried both ethernet ports on my PC. But then again, that is irrelevant because none of my other PC's which connect wirelessly, can connect either.
View 5 Replies
View Related
Sep 8, 2010
I my parents have a WRT54G linksys router, they have a DSL modem. Everything was working fine with the wireless network until one random day POOF! the wireless no longer would connect on laptops. However, the internet is working just fine with the computer that is hardwired up throught the router. Since this is working it lets me know that the router is working fine and routing the connection through hardwire. Hard wired works on laptops but all laptops are unable to join the network and most of the time it will not show up in the list of available networks.Even my iphone wont connect saying unable to join network. We bought a brand new linksys router and same problem. I then took his old router to my house and hooked it up...and WOW it works as it should all devices can connect...even my iphone.
View 2 Replies
View Related
Dec 13, 2011
i have a LINKSYS  WRT54G router .. i bought an apple ipod touch recently  and i am unable to connect it to my wifi network. My ipod detects the wifi network but when i select it , it asks for password. now i dont know which password is this bcoz everytime i poer on my computer or laptop i never type a password b4 accessing internet.. it is auto connected. i know the admin password for my router but that is denied by ipod to connect to internet. Is there any other password we have to give for connecting deveices through LINKSYS or some changes i need to do in my connection ?
View 2 Replies
View Related
Oct 12, 2010
I am replacing a WRH54G with a WRT54G. Â First I unplugged everything and waited 5 minutes. Then I plugged my ethernet cord from the DSL modem into the WRT54G. Then I plugged in the DSL modem. I waited for the lights to stop blinking. Then I plugged in the WRT54G and waited for LEDs to show connection. Then I plugged the ethernet cord from the WRT54G to the computer. Then I turned on the computer. I was able to access the Interface for the WRT54G but I was not able to connect to the internet. I tried power cycling multiple times both the DSL modem and the WRT54G. I was unable to access the internet. Finally I plugged the WRH54G back in and everything worked fine. why the old WRH54G can connect to the internet and the WRT54G cannot?
View 9 Replies
View Related
Nov 23, 2011
 I have a new android, MyTouch Q, through T-mobile.  The phone says it is connected and the wireless icon appears, but I can't access any data or websites.  I've done a hard reset, unplugged both the router and the modem for several minutes, called the phone manufacturer (LG), the carrier (t-mobile), and the internet provider (Cox cable).
View 3 Replies
View Related
Nov 19, 2011
My router used to work. I updated the firmware to 4.21. xx and after that I can't connect to internet.When I connect directly to modem, I can go to the internet . I power recycled etc but when I connect to the router, it says limited connectivity. It shows autoconfigurtion ip:169.254.251.135. I don't know why this is so.I don't have the setup cd disk but I read the users' guide and it seems that I really don;t need the cd. But no matter what I do , I can't get to 192.168.1.1 .
View 4 Replies
View Related
Aug 28, 2011
I have a wrt54g v5 router. I cannot connect to the internet through my router. I called the cable company and they told me that the router probably reset from a power outtage and reconnect. i power cycled, i tried to log onto the router via 192.168.1.1 but the connections were spanish to me.
View 2 Replies
View Related
May 20, 2012
I owned a WRT54G and have been using it for years with no issue.I'm considering of trying to move this to another room by adding powerline network to the home with something like Linksys PLSK400.
View 1 Replies
View Related
Jan 31, 2013
Is there a way to connect my usb only printer to my WRT54g router?
View 1 Replies
View Related
Feb 20, 2010
Checked cable router (brighthouse), working. Router (all lights on but network traffic flashing indicates one way traffic). So I go to my wife's computer. It too has no connection. I open my laptop to connect to the wireless, IT WORKS! Pull power on Cable Modem and Router, wait 60 secs, power up Cable Modem and then power up Router (I know it wasn't nec to do modem but I wanted a clean start). Wireless is still working, no LAN. I can't even connect 192.168.1.1. Linksys software says it can't detect the modem. Reset time, hit the magic button in the back and sure enough everything stops working (which I figured). Still can't connect to it, and now I've lost wireless. I connect computer directly to Cable Modem and type this message. Seems to me that Router has failed.
View 3 Replies
View Related
Dec 30, 2012
All networking had been working great until recent power failure. Then laptops failed to connect, found my router WRT54G had become insecure. I open the router using "admin", reset Wireless Security and reset my password. Wireless laptops, wireless camera now works fine but now iPhone will not connect? I have double checked the password, it is the same as the router. Is there something else in the router that needs changing for the iPhone connection?
Â
[code]...
View 3 Replies
View Related
