Linksys Wireless Router :: Will WRTU54G-TM Bridge With Actiontec?

Jan 27, 2012

I have a Verizon supplied actiontec g band router, and would like to place a WRTU54G-TM on the other side of the house to act as a repeater or a wireless bridge (?). I want stronger wireless at that other side of the house and beyond, and use cat5 to hook up some other devices.Can I bridge the actiontec and WRTU54G-TM together, or do they have to be the same brands?

View 1 Replies


ADVERTISEMENT

Linksys Wireless Router :: How To Connect Two WRTU54G Together

Apr 30, 2012

I have AT&T DSL service and a WRTU54G-TM for my wireless router and T-Mobile at Home phone service. The router is in the basement and upstairs near the back of the house Internet connectivity is weak. I have a second router, identical to the first, that I am hoping can be connected to the first, perhaps as a bridge(?).

View 3 Replies View Related

Linksys Wireless Router :: WRTU54G-TM - Phone Line Has Been Dropping?

Jan 18, 2012

The last couple of weeks the phone line has been dropping until I unplug for about 30 seconds to reset. It is happening more frequently.  The phone service through TMobile gets a dial tone and rings several times then drops when making a call.

View 9 Replies View Related

Linksys Wireless Router :: Tmobile WRTU54G-TM Connection To VOIP Service?

Jan 18, 2012

A client is using Tmobile VOIP using the aforementioned WRTU54G-TM 2-line VOIP wireless router with 4-port hub.  What they would like to do is to place this in their network and NOT have it change (route) the network addresses being assigned to devices 'behind' this router so even their wireless devices are all "on the same network" as the wired devices BEFORE this unit,  In essence, preserve the same 'network and subnet mask' that is being issued by their DSL router via it's integrated DHCP server. ... Rather like operating this unit like an 'access point' instead of a router.Under most circumstances, I might try to assign this router a static IP outside the scope of the DHCP range the DSL router would supply, then plug the (gigabit) Ethernet network cable into one of the 4 Ethernet ports on the rear of this router - but apparently this does not 'facilitate' a connection to Tmobile's VOIP service.When attempting to do this, the connected telephone devices do not get a phone line connection and the status light(s) that normally indicate proper operation do not illuminate.

View 3 Replies View Related

Linksys Wireless Router :: Is Wrtu54g-tm Affected By Wifi Protected Setup

Feb 23, 2012

Is WRTU54G-TM affected by Wi-Fi Protected Setup security vulnerability? Device is not mentioned on this list: url..If yes, can it be fixed or is device bricked?

View 1 Replies View Related

Linksys Wireless Router :: E1200 With Verizon Fios Actiontec?

Feb 8, 2012

I bought the Linksys E1200 for it's wireless N and the guest account. set up my new Linksys E1200 router to use for wireless N access rather that my Verizon Fios provided Actiontec (model M4124-WR Rev.C) which is only wireless G, and so that I can use the guest account. I have an ethernet cable running from one of the 4 ethernet ports on the E1200 to one of the 4 LAN ports on the Actiontec. I have the wireless turned off on the Actiontec, and have the E1200 set as 192.168.1.200.My wireless N signal seems to be working fine from the E1200, and I was able to turn on the guest account on the E1200 and "connect" to it on my iPhone 4, but then when I open Safari I can not connect to the internet.

View 9 Replies View Related

Linksys Wireless Router :: WRT54G FIOS And Actiontec Modem

Dec 29, 2006

Just had Verizon FIOS  service installed.  It comes with an actiontec modem.  I would like to remove the actiontec modem and connect directly to my Linksys RT31P2 which is cascaded to my Linksys WRT54G.  I have tried just about every router setup config; all with no success.  How to be able to connect the FIOS directly to a linksys router.

View 3 Replies View Related

Linksys Wireless Router :: No Internet With WRT160N & GT701 Actiontec?

Oct 9, 2010

I had an old MS DSL1000 that was upgraded by Qwest to an Actiontec GT701 (not wireless) modem. If the GT701 is plugged directly into the PC, the internet works fine. If it is connected from the ethernet port into the WRT160N router, the LAN works but not the internet, even though the internet light is a solid green on the GT701. I've read about port forwarding and DMZ, but still not positive if I should do one or the other, much less on how to go about setting either of them up correctly.

View 9 Replies View Related

Linksys Wireless Router :: EA6500 No Internet Connected To Verizon FIOS Actiontec Router

Jan 20, 2013

I connected EA6500 internet port to actiontec router provided by Verizon fios. I don't have any other way to connect as FIOS connection is coax to actiontec modem. I must take a drop from actiontec to internet port on EA6500.
 
With that said, I can't get EA6500 to work, it keeps saying no internet. The only way I can get it to work is when I set it to bridge mode. This makes my EA6500 a dumb switch/access point. I didn't spend $200 for a switch. I need to use advanced features offered by this router but I can't until this problem is fixed. I made sure I am running latest version of firmware (1.1.28.146856).
 
I have reset my fios router as well as ea6500 to factory defaults multiple times.

View 9 Replies View Related

Connecting Airport Extreme To Linksys WRTU54G-TM?

Aug 16, 2011

how to Cascade two routers on one subnet, but when I disable DHCP on the slave router, I cannot add in any DNS settings.

View 4 Replies View Related

WRTU54G-TM And E1200 - Connecting Two Wireless Routers

Aug 21, 2012

We have a Linksys WRTU54G-TM that serves both as a hotspot and phone line (T-Mobile). But since it's a G, the radius doesn't cover the whole house. So instead of buying an antenna, we bought another router (Cisco Factory Refurbished Linksys E1200 Advanced Wireless-N).

So the question is: How do we connect both routers to one modem properly, the N-Wireless to be used when necessary?

View 6 Replies View Related

Actiontec M1424WR Wireless Router - Setting Up Homegroup

Dec 18, 2012

I recently moved in with a friend, and we're having trouble setting up file sharing. His PC is connected directly (via ethernet cable) to an Actiontec M1424WR wireless router, which is broadcasting a WEP-secured wireless network. My PC is connected wirelessly (via an RNX-N180UBE usb adapter). Both machines are running Windows 7. Internet access is great. We tried to set up a homegroup, however, and are getting nothing but problems.He created a homegroup on his PC, gave me the password, and I joined on my PC. It said it joined and asked me what I wanted to share, but that's as far as we can get.

- On his PC, when he goes to the Homegroup page, it says "no other Homegroup computers are available."
- On my PC's Homegroup page, I see his computer name listed, and when I open it it shows libraries, but when I double click them it nothing happens
- He right-clicked his "downloads" folder and did "share with -> Homegroup;" I see it in my PC's Homegroup page but when I try to open it, the system thinks for a while before popping up a "cannot access" message
- I also shared a folder of mine to the Homegroup but, since he can't even see my PC, he can't see the folder
- I ran IPCONFIG on both machines; his machine's IP is 192.168.1.2; my machine's IP is 192.168.1.5
- When I ping his machine from my machine, I get "request timed out"
- When I ping my machine from his machine, I get replies.
- When I ping the router from my machine, I get replies.
- He has a printer. On my Homegroup page, it tells me that it has detected a new printer, but the "Install Now" button does nothing.

I've gone into Network and Sharing Center -> Advanced Sharing Settings and enabled "Allow Windows to manage homegroup connections." I did this on both machines.He runs a VPN on his machine. Thought that might be the problem, so we turned it off but nothing changed. I run both Hamachi and Tunngle on my machine. Disabled both of those but nothing changed.

View 2 Replies View Related

Linksys Wireless Router :: How To Use EA4500 As A Bridge

May 15, 2013

In my apartment, I can receive the wireless signal of free scholl wireless, which is accessable without user name and password. Although the signal is not good, but we used to use a router EA3000 to relay the signal. Now my roommate is leaving with this this router. So I bought EA4500 and try to do the similar job. However, I find that the configurations on 192.168.1.1 are different between EA3000 and EA4500. Many options cannot be found in the EA4500 page, such as the wireless client.

View 4 Replies View Related

Linksys Wireless Router :: Using E4200 In Bridge Mode?

May 1, 2012

I have a E4200 with 1.0.04 firmware that I've used for a while as a router in front of a cable modem. I have upgraded the modem to a Virgin Media SuperHub. I have connected my E4200's WAN port to one of the SuperHub's LAN ports and changed the E4200's mode to Bridged Mode.I can connect to the Internet wirelessly and wired on the SuperHub, but I can only connect to the Internet via the E4200 if I'm wired to it. The wireless will connect to the E4200, it gets allocated and IP address in the correct range and the gateway is shown as the SuperHub's IP address, and I can see the E4200's management website via wireless, but I cannot connect to anything beyond the E4200.

View 9 Replies View Related

Linksys Wireless Router :: E4200 - How To Bridge Old Belkin G To New

Aug 21, 2011

In order to improve the coverage, how can I bridge my old Belkin G Wireless Router to my new E4200 router ?

View 3 Replies View Related

Linksys Wireless Router :: How To Setup WRT320N As Bridge

Aug 16, 2011

I want to setup the following:
 
Internet through DSL-Thompson TG 789 VN router ---> several yards --> Linksys WRT320N --> wired computer netwerk                                           |             |with   printer                                
|                                                                                             |
---> Wireless Netwerk -->   laptops / phones       <---     (WAN depending on strongest signal)
|
---> several servers
 
The Thompson does the DHCP and routing. It is the gateway through the internet, IP 192.168.2.254 (mask 255.255.255.0).I can't replace the thompson since it is delivered by my provider. SSID = BertB I want to achieve that all the compuers / laptops / phone and printer are in one network and can communicate with each other So the only possibility, as far as I can see, is to set up the Linksys as a bridge.
 
I have to do the following at the Linksys but have some questions as mentioned below:

SSID = BertB (the same)
channel = different from the channel used by Thompson
DHCP = off
IP = fixed (192.168.2.253)
gateway = 192.168.2.254

[code]....

how the thompson and the Linksys will build a connection with each other, or will this happen automatically through the above setup?Do I have to put the mac address of the thompson in the Linksys and/or vice versa?

View 1 Replies View Related

Linksys Wireless Router :: Setup E3000 As Bridge?

Feb 24, 2012

I've small corporate network with Cisco 800 as main DSL router/firewall/DHCP. I'd like to setup Linksys E3000 (firmware: 1.0.01) as bridge (no DHCP, only wireless repeater), but there is no "bridge mode" in E3000 interface

View 9 Replies View Related

Linksys Wireless Router :: WRT54G What Is An Ethernet Bridge

Jul 2, 2011

These questions are only in relation to the above Wireless Router (v6, FW-v1.02 [2010]) :
 
1. What is an Ethernet Bridge (the basic authoritative definition), and besides gaming, what are they generally used for in a business setting?
 
2. What are VPN settings in a Router used for, and can a VPN be configured on a remote PC without them?
 
3.  Utilizing bridging, etc., can I utilize my WRT54G as a makeshift Range Expander as long as the primary router doesnt have WEP key requirements?  The current WIFI doesnt reach my PC, so I thought I could configure my router midway in hopes of extending the other routers' signal, via some kind of bridging if necessary.  Naturally, there would only be a wireless connection between routers.
 
4.  How can I setup a simple Captive Portal on this router?

View 1 Replies View Related

Linksys Wireless Router :: Using EA3500 In Bridge Mode?

Feb 16, 2013

I bought the EA3500 nine months ago mainly for the USB port (for a NAS). I recently replaced Comcast Cable with Verizon FIOS. So I now have the FIOS router as my main router (its' IP address is 192.168.1.1). I put the EA3500 in bridge mode to extend the (wired) network. I could get: After going in to bridge mode (with DHCP), I can not log in to the EA3500 (IP address 192.168.1.5 assigned by the FIOS router). I connect my computer directly to one of  the EA3500 numbered ports (after various combinations of rebooting EA3500 and rebooting PC). It just continues to say "waiting" and never logs in. Tried choosing a static route (tried both 192.168.1.43 and 192.168.1.5 with 255.255.255.0, gateway and DNS1 = 192.168.1.1) with no luck.Since I can't log in, I cannot set up my NAS on the USB port of the EA3500 (so I haven't gotten far enough to determine if the USB port will even work in bridge mode).Thought about ensuring the latest firmware but since I can't log in I can't do that. (And after a hard reset EA3500 IP address is 192.168.1.1 which creates conflict with FIOS)

View 9 Replies View Related

Linksys Wireless Router :: WRT160N - How To Bridge Modem

Feb 6, 2012

I just figured out how to bridge my modem, it was working perfectly. I was walked through by my ISP. So I KNOW it's correct.When I go to set up PPPoE with my WRT160N V2 router, I seeUsername:Password:Service Name (optional)(unchecked) Connect on Deman: Max Idle Time(checked) Keep Alive: Redial Period 30 secondsI KNOW my user and pass are correct but i still have no internet when I bridge my router and put in the info.My modem has DHCP turned off so i turned it off on my router too...nothing.Basically what all settings do I need to change in the  ROUTER ALONE to make this work when setting up a PPPoEbtw setup is

ISP>Modem>Router>Computer

View 6 Replies View Related

Linksys Wireless Router :: Setting WRT160N As Bridge?

Dec 3, 2012

I upgraded the firmware to v3.0. I expected a "Bridge" connection type option, but non appears. How do I set the WRT160N as a bridge?

View 1 Replies View Related

Linksys Wireless Router :: Use E2000 As Wifi Bridge?

Mar 9, 2011

After getting informed that I cannot use the AP I bought yesterday as a bridge, I decided to get another linksys E2000, as the guy in the shop informed me that I can run it in bridge mode for sure.Now, as I am doing this for the first time, and my english is not the best, I was not able to find some instructions, or even better a step-by-step manual that can assist me. I searched the forum, but I did not find anything about the E2000 in bridge mode.

View 7 Replies View Related

Linksys Wireless Router :: E4200 Possible To Put It Into Bridge Mode

Sep 26, 2011

As I understand, the latest FW for the E4200 makes it possible to put he router into bridge mode. In this mode, I can use it as an access point. In bridge mode, should I then connect my router to the WAN port at the E4200?The other way to make the E4200 into an AP, is to disable DHCP and NAT and give the E4200 an IP address out of range for the DHCP range in my preferred router.

Choosing between this two option to make the E4200 into an AP, which is considered to be the best solution?And to be sure; using this option, then the Ethernet cable should be connected to the LAN port of the E4200? is the performance of an E4200 in AP mode the same as a dedicated AP like the WAP610N?

View 3 Replies View Related

Linksys Wireless Router :: E4200 In Bridge Mode

Aug 20, 2011

Just bought 2 e4200's!  I have the first one connected to the ATT router, and I have the second one connected to the first in Bridge Mode.  It works great! It knew how to configure itself to be the down-level client.
 
However, I noticed that the port speed is only 100 Mbps on the port that is acting as the link for the bridge.  I am running brand-new CAT5e thru the house, and if I connect the cable directly to my laptop - I get 1Gbps. So I know that the cable is good.
 
Is there a way to change the speed of the INET port on the down-level e4200? 

View 1 Replies View Related

Linksys Wireless Router :: EA4500 Bridge Mode Might Have A Bug

Jun 20, 2012

Started setting up a Linksys EA4500 Yesterday.
 
- Bridge Mode
- Router Address Manually specified
- Manual wifi setup
 
Regular access works. My smartphone obtains IP address, connects, accesses pages.Guest access loops through the "obtain IP address" step. Bridge mode might have a bug?

View 9 Replies View Related

Linksys Wireless Router :: E4200 Bridge - Would This Be The Way To Go For Max Wifi?

Dec 19, 2011

My e4200 v2 arrived today to replace my v1. I installed it along with a re1000 range expander for our big home. Works pretty well now, but did some google searching and it seems i could make my original e4200 into a bridge, would this be the way to go for max wifi? I could run a cat 6 cable upstairs along the outside of the home fairly easily.

View 9 Replies View Related

Linksys Wireless Router :: Use WRT54G2 In Bridge Mode?

Dec 25, 2011

I have just received my 2 new cheap wrt54g2 routers. I already have a router with dhcp in my network, so I just need this routers to connect wired net and wireless. Is there any way to use this routers as a bridge? Earlier I used asus router, with disabled dhcp and lan cable connected to one of lan ports. But this is not comfortable, because I need to put ip address to router statically

View 6 Replies View Related

Linksys Wireless Router :: E4200V1 With Bridge Mode?

Aug 22, 2012

I have a Wireless Router supplied by my ISP that give me both 1G Lan and N Band Wireless, so I just need to use my 4200V1 as a Storage Access Point.  I have done all the Bridge Mode configurations, IP Address ad Subnet / Default Gateway, etc to the routher and can see it on my Local LAN, by it's Set name. 
 
I can not http or Https to the Config menu in any way, so I can not establish if a Disk is connected or not.  The Disk device is USB Connected to the E4200 port, but I can not acceeass any of the files that are on it. 
 
DGW - 192.168.1.1
E4200 - 192.168.1.200
Bridge Mode
Wireless Disabled on both Bands
DHCP Disabled
 
Everything appears fine, but not able to bring up Advance Configuration interface .

View 2 Replies View Related

Linksys Wireless Router :: E1200 Bridge And Have Wi-Fi DHCP?

Oct 25, 2012

At my work we have Comcast Business Class, and our LAN uses the Comcast's SMC static 10'net addressing.  Our two POS computers are connected to wall ports that connect to the SMC router (unsure its model number, it's screwed to the wall).  There is only 1 LAN port for each POS computer, I am trying to setup a 3rd computer up by the POS stations for dedicated web searching of products, emails between HQ and the other stores. 
 
Like I said our LAN is using the 10'net addressing, and only a single port I can use.  I would like to use the E1200 as a bridge/switch to connect: POS computer, network label printer. and network printer/copier/scanner/FAX .. and also have wifi available.  The POS & printers need to have their static 10'net IPs .. but I want the wifi to use DHCP from the E1200.

View 9 Replies View Related

Linksys Wireless Router :: To Know If Bridge Mode Set Up UTA200

Dec 26, 2008

I have just purchased t-mobile's at home phone service (voip) and they gave me a UTA200-TM Hiport Adaptor to connect for the service.  Had Vonage (voip) for 2 years so know how it works and never had problems.  This one however will only allow the phone line to stay on for about 30 seconds and then drop it.  Have it connected to a modem (cable internet) and a WRT54GS Wireless Router.  T-Mobile wants me to check to see if the router has bridge mode set up as they think that may be causing the phone line to drop out.  How can I check that?  I can not figure out the directions on the linksys site, too confusing.

View 3 Replies View Related

Linksys Wireless Router :: E4200 Works In Bridge Mode Only

Nov 5, 2012

Restarting the e4200 did not work.  Resetting using the switch at the back did not resolve the issue.  I was able to reset it via the 192.168.1.1 web page.  After restoring my settings from backup, the issue remained the same.  This was not alleviated after I updated the firmware.  Plugging into one of the ports with a cat5 cable with my Mac, I was able to get an IP, yet I was not able to surf; same case with my MacBook.
 
Doing the 30-30-30 reboot did not fix this issue and all the while the front white light on the router went and stayed, solid.To see if I could get this to do ANY sort of meaningful internetting (is that even a word?) I put the e4200 in bridge mode and when I put the cable modem in, and all that plugs into this router works.  This, of course, means that there is:
 
1. No Wifi signal and

2. It will not reset to factory settings.

View 1 Replies View Related

Linksys Wireless Router :: EA2700 - Configuring FiOS As Bridge?

Sep 11, 2012

I recently bought an EA2700 in hopes that it will make my connection faster, stronger signal and stable. However, this is not the case. The connections keeps dropping and the range is the same as my Verizon-FiOS router. Anyway, I'm hoping that a fix be distributed to address this issue. I can't return my router to the vendor anymore.
 
Now, since I have two routers, I want to be able to leverage EA2700's dual-band feature and the Guest-access feature but I can't make this as a main router since my FiOS router should still be able to supply IP addresses to my cable boxes, thus, I can't configure it as a Bridge. I'm thinking if I just split the IP distribution as follows:
 
FiOS router: 192.168.1.2-110
EA2700: 192.168.1.111-150

View 4 Replies View Related

Linksys Wireless Router :: Connecting Bridge (WET610N) To E2500

Feb 25, 2012

just replaced my WRT54GL with e2500 and i have a problem connecting my bridge (WET610N) to e2500 router, it connects fine, but no internet when i connect the bridge to another PC (bidrge says it's connected and got IP), same story with another router (WRT54GL) i connect it with the wire to the e2500 than connect to that router with wi fi and OOPS no internet when i connect to e2500 directly with laptop, iphone etc i have the internet connection, but when i connect the bridge or another router i get no internet looks like E2500 does not let the internet pass throught the bridge or other router.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved